iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 20753:2023

(Main)

Plastics - Test specimens (ISO 20753:2023)

Plastics - Test specimens (ISO 20753:2023)

This document specifies dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding, as well as to test specimens prepared by machining from sheets or shaped articles. It compiles the designations and dimensions of test specimens used for the acquisition of comparable data and of other frequently used specimens.
The following types of test specimen are specified:
A            Tensile specimen, multipurpose or reduced-scale
B            Bar specimen
C            Small tensile specimen
D            Square plate specimen
F            Rectangular plate specimen
NOTE    If a particular type of test specimen is not mentioned in this document, this does not mean that there is any intention to exclude the use of the specimen. Additional specimen types can be added in future if they are commonly used.

Kunststoffe - Probekörper (ISO 20753:2023)

Dieses Dokument legt die maßlichen Anforderungen sowohl an Probekörper aus Kunststoffmassen, die zur Bearbeitung durch Formgebung bestimmt sind, als auch an Probekörper fest, die durch die mechanische Bearbeitung von Platten oder Formkörpern hergestellt sind. Es enthält die Bezeichnungen und Maße der zur Erfassung vergleichbarer Daten verwendeten Probekörper und anderer häufig verwendeter Probekörper.
Die folgenden Probekörpertypen sind festgelegt:
A   Zugprobekörper, Vielzweckprobekörper oder verkleinerter Probekörper
B   Stabprobekörper
C   kleiner Zugprobekörper
D   quadratischer Tafelprobekörper
F   rechteckiger Tafelprobekörper
ANMERKUNG   Wenn ein bestimmter Probekörpertyp in diesem Dokument nicht genannt ist, bedeutet das nicht, dass die Absicht besteht, den Probekörper von der Verwendung auszuschließen. Weitere Probekörpertypen können in Zukunft noch ergänzt werden, sofern ihr Gebrauch üblich geworden ist.

Plastiques - Éprouvettes (ISO 20753:2023)

Le présent document fixe des spécifications relatives aux dimensions des éprouvettes préparées à partir de matières plastiques et destinées au traitement par moulage par injection ainsi que des éprouvettes préparées par usinage à partir de feuilles ou d’articles façonnés. Il compile les désignations et les dimensions des éprouvettes utilisées pour l’acquisition de données comparables ainsi que d’autres éprouvettes fréquemment utilisées.
Les types d’éprouvettes suivants sont spécifiés:
A            Éprouvette destinée à la traction, à usages multiples ou à échelle réduite
B            Éprouvette barreau
C            Éprouvette de petite dimension destinée à la traction
D            Éprouvette plaque carrée
F            Éprouvette plaque rectangulaire
NOTE    Si un type particulier d’éprouvettes n’est pas mentionné dans le présent document, cela ne signifie aucunement qu’il existe une intention d’exclure l’utilisation de l’éprouvette. Des types d’éprouvettes supplémentaires pourront être ajoutés à l’avenir s’ils sont fréquemment utilisés.

Polimerni materiali - Preskušanci (ISO 20753:2023)

General Information

Status
Published
Publication Date
12-Dec-2023
ICS
83.080.01 - Plastics in general
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249 - Plastics
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
13-Dec-2023
Completion Date
13-Dec-2023
Ref Project
SIST EN ISO 20753:2024 - Plastics - Test specimens (ISO 20753:2023)

Relations

Replaces
EN ISO 20753:2018 - Plastics - Test specimens (ISO 20753:2018)
Effective Date
18-Jan-2023

Buy Standard

EN ISO 20753:2024EN ISO 20753:2024
PreviousNext
Standard
EN ISO 20753:2024
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 20753:2024
01-februar-2024
Polimerni materiali - Preskušanci (ISO 20753:2023)
Plastics - Test specimens (ISO 20753:2023)
Kunststoffe - Probekörper (ISO 20753:2023)
Plastiques - Éprouvettes (ISO 20753:2023)
Ta slovenski standard je istoveten z: EN ISO 20753:2023
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 20753:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 20753:2024

---------------------- Page: 2 ----------------------
SIST EN ISO 20753:2024


EN ISO 20753
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2023
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 20753:2018
English Version

Plastics - Test specimens (ISO 20753:2023)
Plastiques - Éprouvettes (ISO 20753:2023) Kunststoffe - Probekörper (ISO 20753:2023)
This European Standard was approved by CEN on 7 December 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20753:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 20753:2024
EN ISO 20753:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 20753:2024
EN ISO 20753:2023 (E)
European foreword
This document (EN ISO 20753:2023) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2024, and conflicting national standards shall be
withdrawn at the latest by June 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 20753:2018.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 20753:2023 has been approved by CEN as EN ISO 20753:2023 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 20753:2024

---------------------- Page: 6 ----------------------
SIST EN ISO 20753:2024
INTERNATIONAL ISO
STANDARD 20753
Third edition
2023-11
Plastics — Test specimens
Plastiques — Éprouvettes
Reference number
ISO 20753:2023(E)
© ISO 2023

---------------------- Page: 7 ----------------------
SIST EN ISO 20753:2024
ISO 20753:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized ot
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 22007-1:2024(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)
SIST EN ISO 22007-1:2024

This document describes the background to methods for the determination of the thermal conductivity and thermal diffusivity of polymeric materials. Different techniques are available for these measurements and some can be better suited than others for a particular type, state and form of material. This document provides a broad overview of these techniques. Standards specific to these techniques, as referenced in this document, are used to carry out the actual test method.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22007-4:2024(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 4: Light flash method (ISO 22007-4:2024)
SIST EN ISO 22007-4:2024

This document specifies a method for the determination of the thermal diffusivity of a thin solid disc of plastics in the thickness direction by the light flash method. This method is based upon the measurement of the temperature rise at the rear face of the thin-disc specimen produced by a short energy pulse on the front face.
The method is applicable to homogeneous solid plastics as well as composites having an isotropic or orthotropic structure. In general, it covers materials having a thermal diffusivity, α, in the range 1 × 10−7 m2⋅s−1 < α < 1 × 10−4 m2⋅s−1. Measurements can be carried out in gaseous and vacuum environments over a temperature range from −100 °C to +400 °C.
NOTE          For inhomogeneous specimens, the measured values can be specimen thickness dependent.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8256:2023(Main)
Plastics - Determination of tensile-impact strength (ISO 8256:2023)
SIST EN ISO 8256:2024

1.1     This document specifies two methods (method A and method B) for the determination of the tensile-impact strength of plastics under defined conditions. The tests can be described as tensile tests at relatively high strain rates. These methods can be used for rigid materials (as defined in ISO 472), but are especially useful for materials too flexible or too thin to be tested with impact tests conforming to the ISO 179 series or ISO 180.
1.2     These methods are used for investigating the behaviour of specified specimens under specified impact velocities, and for estimating the brittleness or the toughness of specimens within the limitations inherent in the test conditions.
1.3     These methods are applicable both to specimens prepared from moulding materials and to specimens taken from finished or semi-finished products (for example mouldings, laminates, or extruded or cast sheets).
1.4     Results obtained by testing moulded specimens of different dimensions are not necessarily the same. Equally, it is possible that specimens cut from moulded products will not give the same results as specimens of the same dimensions moulded directly from the material. Test results obtained from specimens prepared from moulding compounds cannot be applied directly to mouldings of any given shape, because values may depend on the design of the moulding and the moulding conditions. Results obtained by method A and method B can or can not be comparable.
1.5     These methods are not suitable for use as a source of data for design calculations on components. Information on the typical behaviour of a material can be obtained, however, by testing different types of test specimen prepared under different conditions, and by testing at different temperatures. The two different methods are suitable for production control as well as for quality control.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 61:2023(Main)
Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:2023)
SIST EN ISO 61:2023

This document specifies a method of determining the apparent density, i.e. the mass per unit of volume, of loose material that cannot be poured from a funnel of specified design.
NOTE            For a method of determining the apparent density of loose moulding material that can be poured from a specified funnel, see ISO 60.
This document is applicable to loose moulding materials such as slice, granular or powder.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 24187:2023(Main)
Principles for the analysis of microplastics present in the environment (ISO 24187:2023)
SIST EN ISO 24187:2023

This document describes the principles to be followed in the analysis of microplastics in various environmental matrices. This includes the unique particle size classification of plastics, the use of certain apparatus with regard to sampling, sample preparation, and the determination of representative sample quantities.
The purpose of this document is to specify minimum requirements until specific standards for the different case situations are available. This is important to ensure that the development of the specific standards is done on a consistent basis to ensure that comparison or correlation of results is possible.
This document does not include requirements for monitoring actions.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13927:2023(Main)
Plastics - Simple heat release test using a conical radiant heater and a thermopile detector (ISO 13927:2023)
SIST EN ISO 13927:2023

This document specifies a method suitable for the production control or product development purposes for assessing the heat release rate of essentially flat products exposed in the horizontal orientation to controlled levels of radiant heating with an external igniter. The heat release rate is determined by the use of a thermopile instead of the more accurate oxygen consumption techniques. The time to ignition and sustained flaming are also measured in this test. The mass loss of the test specimen can also be measured optionally.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20200:2023(Main)
Plastics - Determination of the degree of disintegration of plastic materials under composting conditions in a laboratory-scale test (ISO 20200:2023)
SIST EN ISO 20200:2023

This document specifies a method of determining the degree of disintegration of plastic materials when exposed to a laboratory-scale composting environment. The method is not applicable to the determination of the biodegradability of plastic materials under composting conditions. Further testing is necessary to be able to claim compostability.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6186:2023(Main)
Plastics - Determination of pourability (ISO 6186:2023)
SIST EN ISO 6186:2023

This document specifies two methods, A and B, for determining the pourability of plastics in powdered and granular form, by measuring the flow time through a funnel under specified conditions.
From method A, information concerning the processability can be derived, whilst method B is especially designed for process control during manufacture.
The methods specified are not necessarily applicable to all plastics in powdered and granular form.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 179-1:2023(Main)
Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2023)
SIST EN ISO 179-1:2023

This document specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
The method can be used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions. It can also be used for the determination of comparative data from similar types of material.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 180:2023(Main)
Plastics - Determination of Izod impact strength (ISO 180:2023)
SIST EN ISO 180:2023

This document specifies a method for determining the Izod impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
The method is used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day