EN ISO 8492:2004
(Main)Metallic materials - Tube - Flattening test (ISO 8492:1998)
Metallic materials - Tube - Flattening test (ISO 8492:1998)
WI created following Res COCOR 10/2001: approval of ECISS/TC 29 business plan (CC/010719)
Metallische Werkstoffe - Rohr - Ringfaltversuch (ISO 8492:1998)
In dieser Internationalen Norm ist ein Verfahren zur Bestimmung des Faltverhaltens von Metallrohren mit kreisförmigem Querschnitt festgelegt. Diese Prüfung darf auch zur Sichtbarmachung von Fehlern in Rohren angewendet werden.
Diese Internationale Norm ist anwendbar auf Rohre mit einem Außendurchmesser nicht größer als 600 mm und einer Wanddicke nicht größer als 15 % des Außendurchmessers. Der Bereich des Außendurchmessers oder der Wanddicke, für den diese Internationale Norm zutrifft, kann genauer in der entsprechenden Erzeugnisnorm festgelegt sein.
Matériaux métalliques - Tubes - Essai d'aplatissement (ISO 8492:1998)
Kovinski materiali - Cev - Preskus sploščitve (ISO 8492:1998)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8492:2004
01-november-2004
1DGRPHãþD
SIST EN 10233:1998
.RYLQVNLPDWHULDOL&HY3UHVNXVVSORãþLWYH ,62
Metallic materials - Tube - Flattening test (ISO 8492:1998)
Metallische Werkstoffe - Rohr - Ringfaltversuch (ISO 8492:1998)
Matériaux métalliques - Tubes - Essai d'aplatissement (ISO 8492:1998)
Ta slovenski standard je istoveten z: EN ISO 8492:2004
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 8492:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8492:2004
---------------------- Page: 2 ----------------------
SIST EN ISO 8492:2004
EUROPEAN STANDARD
EN ISO 8492
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2004
ICS 77.040.10 Supersedes EN 10233:1993
English version
Metallic materials - Tube - Flattening test (ISO 8492:1998)
Matériaux métalliques - Tubes - Essai d'aplatissement (ISO Metallische Werkstoffe - Rohr - Ringfaltversuch (ISO
8492:1998) 8492:1998)
This European Standard was approved by CEN on 1 July 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8492:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8492:2004
EN ISO 8492:2004 (E)
Foreword
The text of ISO 8492:1998 has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals” of the International Organization for Standardization (ISO) and
has been taken over as EN ISO 8492:2004 by Technical Committee ECISS/TC 29 "Steel
tubes and fittings for steel tubes", the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by January 2005, and conflicting national
standards shall be withdrawn at the latest by January 2005.
This document supersedes EN 10233:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 8492:1998 has been approved by CEN as EN ISO 8492:2004 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8492:2004
INTERNATIONAL ISO
STANDARD 8492
Second edition
1998-11-01
Metallic materials — Tube — Flattening test
Matériaux métalliques — Tubes — Essai d’aplatissement
A
Reference number
ISO 8492:1998(E)
---------------------- Page: 5 ----------------------
SIST EN ISO 8492:2004
ISO 8492:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Internati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.