iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 4641-202:2018

(Main)

Aerospace series - Cables, optical, 125 µm diameter cladding - Part 202: Semi-loose, ruggedized simplex construction 9/125 µm SM fibre nominal 2,74 mm outside diameter - Product standard

Aerospace series - Cables, optical, 125 µm diameter cladding - Part 202: Semi-loose, ruggedized simplex construction 9/125 µm SM fibre nominal 2,74 mm outside diameter - Product standard

This European product Standard specifies the general characteristics, conditions for qualification, acceptance and quality assurance for a fibre optic cable with a 9/125 µm. Single mode fibre core, 2,74 mm outside cable diameter and of semi-loose construction. The basic construction is the cable defined in EN 4641-102 with added sheaths for ruggedized usages.

Luft- und Raumfahrt - Lichtwellenleiterkabel, Mantelaußendurchmesser 125 μm - Teil 202: Kompaktader, widerstandsfähige Simplexkonstruktion, 9/125 μm SM-Faser, Kabelaußendurchmesser 2,74 mm - Produktnorm

Série aérospatiale - Câbles, optiques, diamètre extérieur de la gaine optique 125 μm - Partie 202 : Câble à structure semi-libre, fibre à SM 9/125 μm, diamètre extérieur 2,74 mm - Norme de produit

Aeronavtika - Kabli, optični, zunanji premer obloge vlakna 125 µm - 202. del: Polohlapna, robustna enoplastna konstrukcija obloge SM 9/125 µm, zunanji premer vlakna 2,74 mm - Standard za proizvod

Ta evropski standard določa splošne lastnosti, pogoje za odobritev in sprejetje ter zagotavljanje kakovosti za kabel iz optičnih vlaken s premerom 9/125 µm. Enoplastno optično jedro, zunanji premer kabla 2,74 mm in pol-ohlapna struktura. Osnovna struktura je kabel, določen v standardu EN 4641-102, z dodanimi oblogami za robustno uporabo.

General Information

Status
Published
Publication Date
27-Nov-2018
Withdrawal Date
30-May-2019
ICS
49.090 - On-board equipment and instruments
Technical Committee
ASD-STAN - Aerospace
Drafting Committee
ASD-STAN/D 2/S 10 - Optical
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
28-Nov-2018
Completion Date
28-Nov-2018
Ref Project
SIST EN 4641-202:2019 - Aerospace series - Cables, optical, 125 µm diameter cladding - Part 202: Semi-loose, ruggedized simplex construction 9/125 µm SM fibre nominal 2,74 mm outside diameter - Product standard

Buy Standard

EN 4641-202:2019EN 4641-202:2019
PreviousNext
Standard
EN 4641-202:2019
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.]XQDQMLLuft- und Raumfahrt - Lichtwellenleiterkabel, Mantelaußendurchmesser 125 µm - Teil 202: Kompaktader, 9/125 µm SM-Faser, Kabelaußendurchmesser 2,74 mm - ProduktnormAerospace series - Cables, optical, 125 µm diameter cladding - Part 202: Semi-loose, ruggedized simplex construction 9/125 µm SM fibre nominal 2,74 mm outside diameter - Product standard49.060Aerospace electric equipment and systems33.180.10Fibres and cablesICS:Ta slovenski standard je istoveten z:EN 4641-202:2018SIST EN 4641-202:2019en,fr,de01-februar-2019SIST EN 4641-202:2019SLOVENSKI
STANDARD



SIST EN 4641-202:2019



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4641-202
November
t r s z ICS
v {ä r { r English Version
Aerospace series æ Cablesá opticalá
s t w
Ám diameter cladding æ Part
t r tã Semiælooseá ruggedized simplex bre nominal
tá y v mm outside diameter æ Product standard Série aérospatiale æ Câblesá optiquesá diamètre extérieur de la gaine optique
s t w
Ám æ Partie
t r t ã diamètre extérieur
tá y v mm æ Norme de produit
Luftæ und Raumfahrt æ Lichtwellenleiterkabelá Mantelaußendurchmesser
s t w
Ám æ Teil
t r tã Kabelaußendurchmesser
tá y v mm æ Produktnorm This European Standard was approved by CEN on
z July
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v x v sæ t r tã t r s z ESIST EN 4641-202:2019



EN 4641-202:2018 (E) 2
Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Required characteristics . 4 5 Cable construction . 5 6 Materials . 6 7 Test methods and performances . 6 8 Tooling . 13 9 Quality assurance . 13 10 Designation and marking . 13 11 Delivery conditions . 13 12 Storage . 14 13 Technical specification . 14
SIST EN 4641-202:2019



EN 4641-202:2018 (E) 3
European foreword This document (EN 4641-202:2018) has been prepared
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 3375-009:2023(Main)
Aerospace series - Cable, electrical, for digital data transmission - Part 009: Single braid - CAN Bus - 120 ohms - Type WX - Product standard
SIST EN 3375-009:2023

This document specifies the required characteristics of single braid, 120 ohms, size 26, electrical cable type WX, UV laser markable, intended for digital data transmissions.
It is used together with EN 3375 001.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2591-509:2023(Main)
Aerospace series - Elements of electrical and optical connection - Test methods - Part 509: Adhesion of coating on contacts
SIST EN 2591-509:2023

This document specifies methods of verifying adhesion of electrodeposited gold and gold alloy coatings on contacts.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2591-508:2023(Main)
Aerospace series - Elements of electrical and optical connection - Test methods - Part 508: Measurement of thickness of coating on contacts
SIST EN 2591-508:2023

This document specifies methods of measuring thickness of electro-deposited gold or gold alloys coatings on contacts of elements of connection.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 3375-011:2022(Main)
Aerospace series - Cable, electrical for digital data transmission - Part 011: Single braid - Star Quad 100 ohms - Lightweight - Type KL - Product standard
SIST EN 3375-011:2023

This document specifies the dimensions, tolerances, required characteristics and the mass of an AWG 24 shielded quad cable, type KL, intended for high speed (100 Mbit/s) full duplex Ethernet networks.
Linked to this particular application, the operating temperatures of the cable are between −65 °C and 125 °C.
This cable is laser markable, this marking satisfies the requirements of EN 3838.
The impedance is 100 Ω ± 15 Ω.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 3375-001:2022(Main)
Aerospace series - Cable, electrical, for digital data transmission - Part 001: Technical specification
SIST EN 3375-001:2022

This document specifies the required characteristics, test methods, qualification and acceptance conditions of signal data transmission electrical cables.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 3745-412:2022(Main)
Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 412: Humidity resistance
SIST EN 3745-412:2022

This document evaluates the resistance of the fiber optic cable to humidity changes at different
temperatures.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4641-301:2022(Main)
Aerospace series - Cables, optical 125 μm diameter cladding - Part 301: Tight structure 50/125 μm GI, fibre nominal 1,8 mm, outside diameter - Product standard
SIST EN 4641-301:2022

This document specifies the general characteristics, conditions for qualification, acceptance and quality assurance for a fibre optic cable with a 50/125 μm Graded Index fibre core, 1,8 mm outside diameter for non pull-proof contact designs.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4533-001:2020(Main)
Aerospace series - Fibre optic systems - Handbook - Part 001: Termination methods and tools
SIST EN 4533-001:2020

1.1   General
Part 001 of EN 4533 examines the termination of optical fibre cables used in aerospace applications. Termination is the act of installing an optical terminus onto the end of a buffered fibre or fibre optic cable. It encompasses several sequential procedures or practices. Although termini will have specific termination procedures, many share common elements and these are discussed in this document. Termination is required to form an optical link between any two network or system components or to join fibre optic links together.
The fibre optic terminus features a precision ferrule with a tight tolerance central bore hole to accommodate the optical fibre (suitably bonded in place and highly polished). Accurate alignment with another (mating) terminus will be provided within the interconnect (or connector) alignment mechanism. As well as single fibre ferrules, it is noted that multi-fibre ferrules exist (e.g. the MT ferrule) and these will also be discussed in this part of the handbook.
Another technology used to connect 2 fibres is the expanded beam. 2 ball lenses are used to expand, collimate and then refocus the light from and to fibres. Contacts are not mated together. It helps reducing the wear between 2 contacts and allows more mating cycles. This technology is less sensitive to misalignments and dust. Losses are remaining more stable than butt joint contact even if the nominal loss is higher.
A Note on Terminology
Current terminology in the aerospace fibre optics community refers to an optical terminus or termini. The term optical contact may be seen in some documents and has a similar meaning. However, the term contact is now generally reserved for electrical interconnection pins. The optical terminus (or termini) is housed within an interconnect (connector is an equivalent term). Interconnects can be single-way or multi-way. The interconnect or connector will generally house the alignment mechanism for the optical termini (usually a precision split-C sleeve made of ceramic or metal). The reader should be aware of these different terms.
An optical link can be classified as a length of fibre optic cable terminated at both ends with fibre optic termini. The optical link provides the transmission line between any two components via the optical termini which are typically housed within an interconnecting device (typically a connector) with tight tolerancing within the alignment mechanisms to ensure a low loss light transmission.
Part 001 will explain the need for high integrity terminations, provide an insight into component selection issues and suggests best practice when terminating fibres into termini for high integrity applications. A detailed review of the termination process can be found in section 4 of this part and is organised in line with the sequence of a typical termination procedure.
The vast number of cable constructions and connectors available make defining a single termination instruction that is applicable to all combinations very difficult. Therefore, this handbook concentrates on the common features of most termination practices and defining best practice for current to near future applications of fibre optics on aircraft. This has limited the studies within this part to currently available ‘avionic’ silica fibre cables and adhesive filled butt-coupled type connectors. Many of the principles described however would still be applicable for other termination techniques. Other types of termination are considered further in the repair part of this handbook.
It is noted that the adhesive based pot-and-polish process is applicable to the majority of single-way fibre optic interconnects connectors and termini for multi-way interconnects and connectors. They share this commonality.
1.2   Need to high integrity terminations
(...)

  • Standard
    113 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 3745-404:2019(Main)
Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 404: Thermal shock
SIST EN 3745-404:2019

This document specifies a method to determine the effects of thermal shock on an optical fibre or cable.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4660-005:2019(Main)
Aerospace series - Modular and Open Avionics Architectures - Part 005: Software
SIST EN 4660-005:2019

This European Standard establishes uniform requirements for design and development of software
architecture for modular avionics systems.

  • Standard
    321 pages
    English language
    sale 10% off
    e-Library read for
    1 day