EN 13445-5:2002/A10:2008

Unfired pressure vessels - Part 5: Inspection and testing

Amendment for  determination of proof test pressure in EN 13445-5.

Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung

Récipients sous pression non soumis à la flamme - Partie 5: Inspection et contrôle

Neogrevane tlačne posode - 5. del: Kontrola in preskušanje

General Information

• Status: Withdrawn
• Publication Date: 30-Sep-2008
• Withdrawal Date: 21-Jul-2009
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• Technical Committee: CEN/TC 54 - Unfired pressure vessels
• Drafting Committee: CEN/TC 54/WG 55 - E - Inspection and testing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 22-Jul-2009
• Completion Date: 22-Jul-2009
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 13445-5:2002/A10:2009 - Unfired pressure vessels - Part 5: Inspection and testing

Relations

• Replaced By: EN 13445-5:2009 - Unfired pressure vessels - Part 5: Inspection and testing
• Effective Date: 08-Jun-2022
• Amends: EN 13445-5:2002 - Unfired pressure vessels - Part 5: Inspection and testing
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2009
1HRJUHYDQHWODþQHSRVRGHGHO.RQWURODLQSUHVNXãDQMH
Unfired pressure vessels - Part 5: Inspection and testing
Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
Récipients sous pression non soumis à la flamme - Partie 5 : Inspection et contrôle
Ta slovenski standard je istoveten z: EN 13445-5:2002/A10:2008
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13445-5:2002/A10
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2008
ICS 23.020.30
English Version
Unfired pressure vessels - Part 5: Inspection and testing
Récipients sous pression non soumis à la flamme - Partie Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
5: Inspection et contrôle
This amendment A10 modifies the European Standard EN 13445-5:2002; it was approved by CEN on 25 July 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-5:2002/A10:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
6.6 Non destructive testing of welded joints .4
10 Final assessment.4

Foreword
This document (EN 13445-5:2002/A10:2008) has been prepared by Technical Committee CEN/TC 54
“Unfired pressure vessels”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 13445-5:2002 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by April 2009, and conflicting national
standards shall be withdrawn at the latest by April 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annex ZA which is an integral part of this document.
This amendment is based on EN 13445-5 up to issue 29 (October 2007).
The document includes the text of the amendment itself. The corrected pages of EN 13445-5 will be delivered
as issue 32 of the standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

6.6 Non destructive testing of welded joints
6.6.1.1.2 Testing groups 1, 2 and 3
Replace the text above list a), b) and c) by:
It is intended that a single testing group is applied to the entire vessel.
When the vessel is made of several sections (courses), a combination of testing groups 1, 2, and 3 is
permissible providing that the requirements of Table 6.6.1-1 are met. If a combination of testing groups is
necessary, for example as the result the use of DBA Direct Route, of the Alternative Route, of design in the
creep range or for fatigue in a section (course), the following shall apply:

10 Final assessment
10.2.3.3 Standard hydrostatic test
In 10.2.3.3.1, replace the text up to e by the following:

1)
10.2.3.3.1 For a single-compartment vessel subjected to internal pressure, working below the creep
range, and designed according to testing group 1, 2 or 3, the test pressure, applied as internal pressure at the
highest point of the chamber of the vessel for either horizontal or vertical test positions, shall be as specified in
a). The modifications of the test pressure due to the hydrostatic pressure are specified in b).
Special provisions are given in c) for single-run governing welds and in d) for complete vessels or parts of
vessels working in the creep range.
a) The test pressure shall be determined by the greater of:
f
a
P = 1,25 ⋅ P ⋅  (10.2.3.3.1-1)
t d
f
T
d
or
P = 1,43 ⋅ P (10.2.3.3.1-2)
t s
where:
P is the test pressure measured at the highest point of the chamber of the vessel in the test position;
t
P and T are the coincident design pressure and design temperature values for the maximum pressure load
d d
case;
P is the maximum allowable pressure of the vessel;
s
f is the nominal design stress for normal operating load cases of the material of the part under consideration
a
at the test temperature;
1) The case of multi-compartme
...