FprEN IEC 62282-3-201:2025
(Main)Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
IEC 62282-3-201:2025 provides test methods for the electrical, thermal, and environmental performance of small stationary fuel cell power systems that meet the following criteria: - output: rated electric power output of less than 10 kW; - output mode: grid-connected/independent operation or stand-alone operation with single-phase AC output or 3-phase AC output not exceeding 1 000 V, or DC output not exceeding 1 500 V; - operating pressure: maximum allowable working pressure of 0,1 MPa (gauge) for the fuel and oxidant passages; - fuel: gaseous fuel (natural gas, liquefied petroleum gas, propane, butane, hydrogen, etc.) or liquid fuel (kerosene, methanol, etc.); - oxidant: air. This document describes type tests and their test methods only. No routine tests are required or identified, and no performance targets are set in this document. This document provides test methods to be carried out under laboratory conditions. This document covers fuel cell power systems whose primary purpose is the production of electric power and whose secondary purpose can be the utilization of heat. Accordingly, fuel cell power systems for which the use of heat is primary, and the use of electric power is secondary are outside the scope of this document. This third edition cancels and replaces the second edition published in 2017 and Amendment 1:2022. This edition includes the following significant technical changes with respect to the previous edition: - revision of Introduction; - revision of terms and definitions; - revision of Table 1; - revision of Figure 1, Figure 2, Figure 3 and Figure 4; - revision of measurement instruments (10.2); - revision of minimum required measurement systematic uncertainty (10.4); - revision of test conditions (Clause 11); - revision of operating process (Clause 12); - revision of fuel consumption test (14.2); - revision of heat recovery test (14.4); - revision of Figure 13 and Figure 14; - revision of calculation of results (14.14.4); - revision of Annex A and Annex B.
Brennstoffzellentechnologien - Teil 3-201: Stationäre Brennstoffzellen-Energiesysteme - Leistungskennwerteprüfverfahren für kleine Brennstoffzellen-Energiesysteme
Technologies des piles à combustible - Partie 3-201: Systèmes à piles à combustible stationnaires - Méthodes d'essai des performances pour petits systèmes à piles à combustible
L'IEC 62282-3-201:2025 fournit des méthodes d’essai relatives aux performances électriques, thermiques et environnementales des petits systèmes à piles à combustible stationnaires qui satisfont aux critères suivants: - puissance de sortie: la puissance électrique de sortie assignée est inférieure à 10 kW; - mode de sortie: fonctionnement raccordé au réseau/indépendant ou fonctionnement autonome avec une sortie en courant alternatif monophasé ou une sortie en courant alternatif triphasé ne dépassant pas 1 000 V ou une sortie en courant continu ne dépassant pas 1 500 V; - pression de fonctionnement: pression de fonctionnement admissible maximale 0,1 MPa (G) pour les passages du combustible et de l’agent oxydant; - combustible: combustible gazeux (gaz naturel, gaz de pétrole liquéfié, propane, butane, hydrogène, etc.) ou combustible liquide (kérosène, méthanol, etc.); - agent oxydant: air. Le présent document décrit uniquement les essais de type et leurs méthodes d’essai. Aucun essai individuel de série n’est exigé ou identifié, et aucune cible de performance n’est définie dans le présent document. Le présent document fournit des méthodes d’essai à appliquer dans des conditions de laboratoire. Le présent document traite des systèmes à piles à combustible dont le but principal est de produire du courant électrique et dont le but secondaire peut être d’utiliser de la chaleur. Par conséquent, les systèmes à piles à combustible dont le but principal est l’utilisation de la chaleur et dont le but secondaire est l’utilisation du courant électrique ne relèvent pas du domaine d’application du présent document. Cette troisième édition annule et remplace la deuxième édition parue en 2017 et son Amendement 1:2022. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente: - révision de l’Introduction, - révision des termes et définitions, - révision du Tableau 1, - révision de la Figure 1, Figure 2, Figure 3 et Figure 4; - révision des appareils de mesure (10.2), - révision de l’incertitude de mesure systématique minimale exigée (10.4), - révision des conditions d’essai (Article 11), - révision du processus de fonctionnement (Article 12), - révision de l’essai de consommation de combustible (14.2), - révision de l’essai d’énergie thermique récupérée (14.4), - révision de la Figure 13 et de la Figure 14, - révision du calcul des résultats (14.14.4), - révision de l’Annexe A et de l’Annexe B.
Tehnologije gorivnih celic - 3-201. del: Nepremični elektroenergetski sistemi z gorivnimi celicami - Metode za preskušanje zmogljivosti majhnih elektroenergetskih sistemov z gorivnimi celicami
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 62282-3-201:2024
01-februar-2024
Tehnologije gorivnih celic - 3-201. del: Nepremični elektroenergetski sistemi z
gorivnimi celicami - Metode za preskušanje zmogljivosti majhnih
elektroenergetskih sistemov z gorivnimi celicami
Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test
methods for small fuel cell power systems
Brennstoffzellentechnologien - Teil 3-201: Stationäre Brennstoffzellen-Energiesysteme -
Leistungskennwerteprüfverfahren für kleine Brennstoffzellen-Energiesysteme
Technologies des piles à combustible - Partie 3-201: Systèmes à piles à combustible
stationnaires - Méthodes d'essai des performances pour petits systèmes à piles à
combustible
Ta slovenski standard je istoveten z: prEN IEC 62282-3-201:2023
ICS:
27.070 Gorilne celice Fuel cells
oSIST prEN IEC 62282-3-201:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN IEC 62282-3-201:2024
oSIST prEN IEC 62282-3-201:2024
105/1012/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 62282-3-201 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2023-11-24 2024-02-16
SUPERSEDES DOCUMENTS:
105/975/CD, 105/989A/CC
IEC TC 105 : FUEL CELL TECHNOLOGIES
SECRETARIAT: SECRETARY:
Germany Mr David Urmann
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if any, in
this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for Vote
(CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some Countries” clauses to
be included should this proposal proceed. Recipients are reminded that the CDV stage is the final stage for submitting ISC clauses.
(See AC/22/2007 or new GUIDANCE DOC).
TITLE:
Fuel cell technologies – Part 3-201: Stationary fuel cell power systems – Performance test methods for small
fuel cell power systems
PROPOSED STABILITY DATE: 2028
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
oSIST prEN IEC 62282-3-201:2024
CDV IEC 62282-3-201 © IEC 2023 – 2 –
CONTENTS
CONTENTS . 2
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Symbols . 15
5 Configuration of small stationary fuel cell power system . 21
6 Reference conditions . 21
7 Heating value base . 21
8 Test preparation . 22
8.1 General . 22
8.2 Uncertainty analysis . 22
8.3 Data acquisition plan . 22
9 Test set-up . 22
10 Instruments and measurement methods . 24
10.1 General . 24
10.2 Measurement instruments . 24
10.3 Measurement points. 25
10.4 Minimum required measurement systematic uncertainty . 27
11 Test conditions . 27
11.1 Laboratory conditions. 27
11.2 Installation and operating conditions of the system . 27
11.3 Power source conditions . 27
11.4 Test fuel . 28
12 Operating process . 28
13 Test plan . 30
14 Type tests on electric and thermal performance . 31
14.1 General . 31
14.2 Fuel consumption test . 31
14.2.1 Gaseous fuel consumption test . 31
14.2.2 Liquid fuel consumption test . 34
14.3 Electric power output test . 35
14.3.1 General . 35
14.3.2 Test method . 35
14.3.3 Calculation of average net electric power output . 36
14.4 Heat recovery test . 36
14.4.1 General . 36
14.4.2 Test method . 36
14.4.3 Calculation of average recovered thermal power . 37
14.5 Start-up test . 38
14.5.1 General . 38
14.5.2 Determination of state of charge of the battery . 38
oSIST prEN IEC 62282-3-201:2024
– 3 – CDV IEC 62282-3-201:Ed.3 © IEC 202X
14.5.3 Test method . 38
14.5.4 Calculation of results . 41
14.6 Ramp-up test . 43
14.6.1 General . 43
14.6.2 Test method . 43
14.6.3 Calculation of results . 43
14.7 Storage state test . 44
14.7.1 General . 44
14.7.2 Test method . 44
14.7.3 Calculation of average electric power input in storage state . 44
14.8 Electric power output change test . 45
14.8.1 General . 45
14.8.2 Test method . 45
14.8.3 Calculation of electric power output change rate . 46
14.9 Shutdown test . 47
14.9.1 General . 47
14.9.2 Test method . 47
14.9.3 Calculation of results . 48
14.10 Computation of efficiency . 49
14.10.1 General . 49
14.10.2 Electrical efficiency . 49
14.10.3 Heat recovery efficiency . 49
14.10.4 Overall energy efficiency . 50
14.11 Rated operation cycle efficiency. 50
14.11.1 General . 50
14.11.2 Calculation of the operation cycle fuel energy input . 50
14.11.3 Calculation of the operation cycle net electric energy output . 51
14.11.4 Calculation of the operation cycle electrical efficiency . 52
14.12 Electromagnetic compatibility (EMC) test . 52
14.12.1 General requirement . 52
14.12.2 Electrostatic discharge immunity test . 53
14.12.3 Radiated, radio-frequency, electromagnetic field immunity test . 53
14.12.4 Electrical fast transient/burst immunity test . 53
14.12.5 Surge immunity test . 53
14.12.6 Immunity test of conducted disturbances induced by radio-frequency
fields . 53
14.12.7 Power frequency magnetic field immunity test . 53
14.12.8 Voltage dips and voltage interruptions . 54
14.12.9 Radiated disturbance (emission) measurement test . 54
14.12.10 Conducted disturbance (emission) measurement test . 54
14.12.11 Power line harmonics emission measurement test . 54
14.13 Estimation of electric and heat recovery efficiency up to ten years of
operation . 54
14.13.1 General . 54
14.13.2 Test method . 55
14.13.3 Calculation of estimated electric efficiency . 56
14.13.4 Calculation of estimated heat recovery efficiency . 58
14.14 Electric demand-following test . 58
oSIST prEN IEC 62282-3-201:2024
CDV IEC 62282-3-201 © IEC 2023 – 4 –
14.14.1 General . 58
14.14.2 Electric demand profile . 58
14.14.3 Test method . 59
14.14.4 Calculation of results .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.