prEN IEC 61810-7-1:2023
(Main)Electrical relays - Tests and measurements - Part 1: Visual inspection and check of dimensions
Electrical relays - Tests and measurements - Part 1: Visual inspection and check of dimensions
Relais électriques - Essais et mesurages - Partie 1: Examen visuel et contrôle des dimensions
Električni releji - Preskusi in meritve - 7-1. del: Vizualni pregled in preverjanje mer
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2023
Električni releji - Preskusi in meritve - 7-1. del: Vizualni pregled in preverjanje mer
Electrical relays - Tests and Measurements - Part 7-1: Visual inspection and check of
dimensions
Ta slovenski standard je istoveten z: prEN IEC 61810-7-1:2023
ICS:
29.120.70 Releji Relays
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
94/878/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61810-7-1 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2023-07-07 2023-09-29
SUPERSEDES DOCUMENTS:
94/837/CD, 94/865/CC
IEC TC 94 : ELECTRICAL RELAYS
SECRETARIAT: SECRETARY:
Austria Mr Bernhard Spalt
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
TC 121,SC 121A
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Electrical relays – Tests and Measurements - Part 7-1: Visual inspection and check of
dimensions
PROPOSED STABILITY DATE: 2026
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
– 2 – IEC CDV 61810-7-1:2023 © IEC 2023
1 CONTENTS
2 FOREWORD . 3
3 1 Scope . 5
4 2 Normative references . 5
5 3 Terms and definitions . 5
6 4 Test procedure . 6
7 5 Evaluation . 8
8 Bibliography . 10
IEC CDV 61810-7-1:2023 © IEC 2023 – 3 –
12 INTERNATIONAL ELECTROTECHNICAL COMMISSION
13 ____________
15 Electrical Relays –
16 Tests and measurements
18 Part 7-1: Visual inspection and check of dimensions
20 FOREWORD
21 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization
22 comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to p
23 2) romote international co-operation on all questions concerning standardization in the electrical and electronic
24 fields. To this end and in addition to other activities, IEC publishes International Standards, Technical
25 Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred
26 to as "IEC Publication(s)"). Their preparation is entrusted to technical committees; any IEC National
27 Committee interested in the subject dealt with may participate in this preparatory work. International,
28 governmental and non-governmental organizations liaising with the IEC also participate in this preparation.
29 IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with
30 conditions determined by agreement between the two organizations.
31 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
32 consensus of opinion on the relevant subjects since each technical committee has representation from all
33 interested IEC National Committees.
34 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
35 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
36 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
37 misinterpretation by any end user.
38 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
39 transparently to the maximum extent possible in their national and regional publications. Any divergence between
40 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
41 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
42 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
43 services carried out by independent certification bodies.
44 6) All users should ensure that they have the latest edition of this publication.
45 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
46 members of its technical committees and IEC National Committees for any personal injury, property damage or
47 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
48 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
49 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
50 indispensable for the correct application of this publication.
51 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
52 rights. IEC shall not be held responsible for identifying any or all such patent rights.
53 The International Standards of the IEC 61810 have been prepared by IEC technical committee
54 94: All-or-nothing electrical relays.
55 The text of this International Standard is based on the following documents:
CD CC
94/837/CC 94/865/CC
57 Full information on the voting for the approval of this International Standard can be found in the
58 report on voting indicated in the above table.
59 This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
60 A list of all parts of IEC 61810 series, published under the general title Electromechanical
61 elementary relays, can be found on the IEC website.
– 4 – IEC CDV 61810-7-1:2023 © IEC 2023
62 This International Standard is to be used in conjunction wit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.