EN 61810-2-1:2017
(Main)Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B10 values
Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B10 values
IEC 61810-2-1:2017 specifies reliability test procedures for electromechanical elementary relays when enhanced requirements for the verification of reliability apply. Particular provisions are given for relays incorporated in safety-related control systems of machinery in accordance with IEC 62061 and ISO 13849-1. For such relays, B10 values for dangerous failures (B10D values) are derived from the tests specified in this document. This edition includes the following significant technical changes with respect to the previous edition: - limitation of tests to 10 M cycles in Clause 5; - reduction of required number of test samples to 5 in specified cases; - introduction of WeiBayes analysis for routine test under Clause 4.
Elektromechanische Elementarrelais - Teil 2-1: Funktionsfähigkeit (Zuverlässigkeit) - Verfahren zum Nachweis der B10-Werte
Relais électromécaniques élémentaires - Partie 2-1: Fiabilité - Procédure de vérification des valeurs de B10
L'IEC 61810-2-1:2017 spécifie les procédures d'essai de fiabilité pour les relais électromécaniques élémentaires lorsque des exigences renforcées pour la vérification de la fiabilité s'appliquent. Des dispositions particulières sont fournies pour les relais incorporés dans les systèmes de commande relatifs à la sécurité des machines selon l'IEC 62061 et l'ISO 13849-1. Pour ces relais, les valeurs de B10 pour des défaillances dangereuses (valeurs de B10D) sont obtenues à partir des essais spécifiés dans le présent document. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - limitation des essais à 10 M de manœuvres à l'Article 5; - réduction du nombre exigé d'échantillons d'essai à 5 dans des cas spécifiés; - introduction de l'analyse de WeiBayes pour l'essai individuel de série à l'Article 4.
Osnovni elektromehanski releji - 2-1. del: Zanesljivost - Postopki za overjanje vrednosti B10
Ta del standarda IEC 61810 določa postopke za preskušanje zanesljivosti za osnovne elektromehanske releje, pri katerih se uporabljajo dopolnjene zahteve za preverjanje zanesljivosti. Za releje, vključene v varnostne sisteme krmiljenja strojev v skladu s standardoma IEC 62061 in ISO 13849-1, so podane posebne določbe. Za take releje so vrednosti B10 za nevarne okvare (vrednosti B10D) izpeljane iz preskusov, opredeljenih v tem dokumentu.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Osnovni elektromehanski releji - 2-1. del: Zanesljivost - Postopki za overjanje vrednosti B10Elektromechanische Elementarrelais - Teil 2-1: Funktionsfähigkeit (Zuverlässigkeit) - Verfahren zum Nachweis der B10-WerteRelais électromécaniques élémentaires - Partie 2-1: Fiabilité - Procédure de vérification des valeurs de B10Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B10 values29.120.70RelejiRelaysICS:Ta slovenski standard je istoveten z:EN 61810-2-1:2017SIST EN 61810-2-1:2018en01-januar-2018SIST EN 61810-2-1:2018SLOVENSKI
STANDARDSIST EN 61810-2-1:20111DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 61810-2-1
October 2017 ICS 29.120.70
Supersedes
EN 61810-2-1:2011
English Version
Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B10 values (IEC 61810-2-1:2017)
Relais électromécaniques élémentaires -
Partie 2-1: Fiabilité - Procédure de vérification des valeurs de B10 (IEC 61810-2-1:2017)
Elektromechanische Elementarrelais -
Teil 2-1: Funktionsfähigkeit (Zuverlässigkeit) - Verfahren zum Nachweis der B10-Werte (IEC 61810-2-1:2017) This European Standard was approved by CENELEC on 2017-07-04. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61810-2-1:2017 E SIST EN 61810-2-1:2018
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-04-06 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-10-06
This document supersedes EN 61810-2-1:2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 61810-2-1:2017 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
ISO 13849-2:2012 NOTE Harmonized as EN ISO 13849-2:2012 (not modified). SIST EN 61810-2-1:2018
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1
Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2
Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61810-1 2015
Electromechanical elementary relays -
Part 1: General and safety requirements EN 61810-1 2015
IEC 61810-2 2017
Electromechanical elementary relays -
Part 2: Reliability EN 61810-2 2017
IEC 61810-3 -
Electromechanical elementary relays -
Part 3: Relays with forcibly guided (mechanically linked) contacts EN 61810-3 -
IEC 62061 -
Safety of machinery - Functional safety
of safety-related electrical, electronic and programmable electronic control systems EN 62061 -
ISO 13849-1 2015
Safety of machinery - Safety-related parts of control systems -
Part 1: General principles for design EN ISO 13849-1 2015
IEC 61810-2-1 Edition 2.0 2017-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Electromechanical elementary relays –
Part 2-1: Reliability – Procedure for the verification of B10 values
Relais électromécaniques élémentaires –
Partie 2-1: Fiabilité – Procédure de vérification des valeurs de B10
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 29.120.70
ISBN 978-2-8322-4389-3
– 2 – IEC 61810-2-1:2017 © IEC 2017 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 6 3.2 Definitions related to tests . 7 4 Verification of B10 . 7 4.1 General . 7 4.2 Requirements . 7 4.2.1 Test specimens . 7 4.2.2 Test circuit . 8 4.2.3 Contact loads . 8 4.2.4 Environmental conditions . 8 4.2.5 Operating conditions . 8 4.2.6 Failure criteria . 8 4.3 Performance of the tests . 9 4.3.1 Type test . 9 4.3.2 Routine test . 9 5 Evaluation and verification of B10D . 9 5.1 General . 9 5.2 Requirements . 10 5.2.1 Test specimens . 10 5.2.2 Test circuit . 10 5.2.3 Contact loads . 11 5.2.4 Environmental conditions . 11 5.2.5 Operating conditions . 11 5.2.6 Failure criteria . 11 5.3 Performance of the tests . 12 5.3.1 Type test . 12 5.3.2 Routine test . 12 Annex A (informative)
Example illustrating the assessment of malfunctions for B10D evaluation . 15 A.1 Purpose . 15 A.2 Basic assumptions . 15 A.3 Example. 15 A.4 Evaluation . 16 Bibliography . 17
Figure 1 – Schematic flowchart . 13 Figure 2 – Schematic flowchart for relays where
dangerous failures have to be assessed . 14
Table A.1 – Example with number of cycles at which malfunctions have been recorded . 15
IEC 61810-2-1:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
ELECTROMECHANICAL ELEMENTARY RELAYS –
Part 2-1: Reliability – Procedure for the verification of B10 values
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61810-2-1 has been prepared by IEC technical committee 94: All-or-nothing electrical relays. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previou
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.