Cable trunking systems and cable ducting systems for electrical installations - Part 2-4: Particular requirements - Service poles and service posts

This part 2-4 of the EN IEC 61084 series specifies particular requirements and tests for service poles and service posts intended to be mounted in free space and in contact with mounting surface(s) only at one or two ends, where the word "mounted" means fixed or placed on the floor with a weighted base or linked to a mounting surface through a flexible component.

Installationskanalsysteme für elektrische Installationen - Teil 2-4: Besondere Anforderungen - Freistehende Installationseinheiten

Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques - Partie 2-4: Exigences particulières - Colonnes et colonnettes

L'IEC 61084-2-4:2017 spécifie les exigences et les essais pour les systèmes de goulottes (SG) et les systèmes de conduits-profilés (SCP) destinés au logement de conducteurs isolés, câbles et éventuels autres équipements électriques et, si nécessaire, à leur séparation de protection électrique, dans des installations électriques et/ou de systèmes de communication. La tension maximale de ces installations est de 1 000 V en courant alternatif et 1 500 V en courant continu. Les colonnes et les colonnettes sont destinées à être montées en espace libre et au contact de la ou des surfaces de montage uniquement à une extrémité ou aux deux extrémités, le mot «montées» signifiant fixées ou placées sur le sol avec une base lestée ou reliées à une surface de montage au moyen d’un composant flexible. NOTE Les colonnes et les colonnettes peuvent aussi faire partie d’un SG/SCP destiné à être monté au mur ou au plafond et relevant de l'IEC 61084-2-1, ou destiné à être monté au sol et relevant de l'IEC 61084-2-2, et sont alors aussi soumises à essai conformément à ces parties selon le cas. La présente norme internationale ne s’applique pas aux systèmes de conduits, systèmes de chemins de câbles, systèmes d’échelles à câbles, systèmes de canalisations préfabriquées ou aux équipements couverts par d’autres normes. Cette deuxième édition annule et remplace la première édition parue en 1996. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - classification; - construction; - propriétés mécaniques et électriques. Cette Norme internationale doit être utilisée conjointement avec l’IEC 61084-1:2017.

Sistemi kabelskih korit in sistemi kabelskih cevi za električne inštalacije - 2-4. del: Posebne zahteve - Podporni drogovi in podporni stebri

General Information

Status
Not Published
Publication Date
12-Sep-2024
Current Stage
5060 - Voting results sent to TC, SR - Formal Approval
Start Date
28-Jun-2024
Due Date
18-Mar-2023
Completion Date
28-Jun-2024

Relations

Buy Standard

Draft
prEN IEC 61084-2-4:2023 - BARVE
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
oSIST prEN IEC 61084-2-4:2023
01-februar-2023
Sistemi kabelskih korit in sistemi kabelskih cevi za električne inštalacije - 2-4. del:
Posebne zahteve - Podporni drogovi in podporni stebri
Cable trunking systems and cable ducting systems for electrical installations - Part 2-4:
Particular requirements - Service poles and service posts
Elektroinstallationskanalsysteme für elektrische Installationen - Teil 2-4: Besondere
Anforderungen für freistehende Installationseinheiten
Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques -
Partie 2-4: Exigences particulières - Colonnes et colonnettes
Ta slovenski standard je istoveten z: prEN IEC 61084-2-4:2022
ICS:
29.120.10 Inštalacijske cevi za Conduits for electrical
električne namene purposes
oSIST prEN IEC 61084-2-4:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN IEC 61084-2-4:2023
oSIST prEN IEC 61084-2-4:2023
EUROPEAN STANDARD DRAFT
prEN IEC 61084-2-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2022
ICS 29.060.01; 29.120.10 Will supersede EN 50085-2-4:2009
English Version
Cable trunking systems and cable ducting systems for electrical
installations - Part 2-4: Particular requirements - Service poles
and service posts
(IEC 61084-2-4:2017)
Systèmes de goulottes et systèmes de conduits-profilés Elektroinstallationskanalsysteme für elektrische
pour installations électriques - Partie 2-4: Exigences Installationen - Teil 2-4: Besondere Anforderungen für
particulières - colonnes et colonnettes freistehende Installationseinheiten
(IEC 61084-2-4:2017) (IEC 61084-2-4:2017)
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2023-03-03.

The text of this draft consists of the text of IEC 61084-2-4:2017.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 72103 Ref. No. prEN IEC 61084-2-4:2022 E

oSIST prEN IEC 61084-2-4:2023
prEN IEC 61084-2-4:2022 (E)
European foreword
This document (prEN IEC 61084-2-4:2022) consists of the text of document IEC 61084-2-4:2017,
prepared by SC 23A "Cable management systems" of IEC/TC 23 "Electrical accessories".
This document is currently submitted to the Enquiry.
The following dates are proposed:
• latest date by which the existence of this document (doa) dor + 6 months
has to be announced at national level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of an
identical national standard or by endorsement
• latest date by which the national standards (dow) dor + 60 months
conflicting with this document have to be withdrawn (to be confirmed or
modified when voting)
This document will supersede EN 50085-2-4:2009 and all of its amendments and corrigenda (if any).
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association, and supports essential requirements
of EU Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZZ, which is an integral part
of prEN IEC 61084-2-4:2022/prAA:2022.

oSIST prEN IEC 61084-2-4:2023
IEC 61084-2-4 ®
Edition 2.0 2017-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Cable trunking systems and cable ducting systems for electrical installations –

Part 2-4: Particular requirements – Service poles and service posts

Systèmes de goulottes et systèmes de conduits-profilés pour installations

électriques –
Partie 2-4: Exigences particulières – Colonnes et colonnettes

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.01; 29.120.10 ISBN 978-2-8322-4123-3

oSIST prEN IEC 61084-2-4:2023
– 2 – IEC 61084-2-4:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 General requirements . 6
5 General conditions for tests . 7
6 Classification . 7
7 Marking and documentation . 8
8 Dimensions. 8
9 Construction . 8
10 Mechanical properties. 10
11 Electrical properties . 16
12 Thermal properties . 17
13 Fire hazard . 17
14 External influences . 18
15 Electromagnetic compatibility . 18
Annex A (informative) Types of cable trunking systems (CTS) and cable ducting
systems (CDS) . 23
Annex B (normative) CTS/CDS IK code . 24
Annex AA (normative) Use of test results according to IEC 61084-2-4:2015 for service
poles and service posts being part of CTS/CDS covered by IEC 61084-2-1:2015 or by
IEC 61084-2-2:2015 . 25
Annex AB (normative) Routine test for the socket outlets wiring of pre-wired service
poles and service posts (correct polarity and protection against electric shock) . 28
Bibliography . 30

Figure 101 – Types and application of service poles and service posts . 20
Figure 102 – Detail of the cylinder for vertical load test in accordance with 10.5.103 . 21
Figure 103 – Detail of the circular plate for vertical load test in accordance with
10.5.104 . 22

Table AA.1 – Use for service poles and service posts being part of CTS/CDS covered
by IEC 61084-2-1:2015 . 25
Table AA.2 – Use for service poles and service posts being part of CTS/CDS covered
by IEC 61084-2-2:2015 . 26
Table AB.1 – Diagrammatic representation of routine tests to be applied to the socket
outlets wiring of pre-wired service poles and service posts . 28

oSIST prEN IEC 61084-2-4:2023
IEC 61084-2-4:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CABLE TRUNKING SYSTEMS AND CABLE DUCTING
SYSTEMS FOR ELECTRICAL INSTALLATIONS –

Part 2-4: Particular requirements – Service poles and service posts

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61084-2-4 has been prepared by subcommittee 23A: Cable
management systems, of IEC technical committee 23: Electrical accessories.
This second edition cancels and replaces the first edition published in 1996. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
• classification;
• construction;
• mechanical and electrical properties.

oSIST prEN IEC 61084-2-4:2023
– 4 – IEC 61084-2-4:2017 © IEC 2017
The text of this standard is based on the following documents:
FDIS Report on voting
23A/830/FDIS 23A/837/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This Internat
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.