CLC/TS 50131-2-2:2004
(Main)Alarm systems - Intrusion systems - Part 2-2: Requirements for passive infrared detectors
Alarm systems - Intrusion systems - Part 2-2: Requirements for passive infrared detectors
Interim TS before EN status (draft expected November 2006 for circulation in spring 2007) * Standstill maintained * Superseded by EN 50131-2-2:2008
2014-05-06 GVN: 1st vote on prEN 50131-2-2:2002 launched on 2002-03-01 until 2002-05-31 followed by an enquiry on CLC/prTS 50131-2-2:2004 launched on 2004-02-20 until 2004-04-23.
Alarmanlagen - Einbruchmeldeanlagen - Teil 2-2: Anforderungen an Passiv-Infrarotmelder
Systèmes d'alarme - Systèmes d'alarme intrusion - Partie 2-2: Exigences pour détecteurs infrarouges passifs
Alarmni sistemi – Sistemi za javljanje vloma – 2-2. del: Zahteve za pasivne infrardeče javljalnike
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2005
$ODUPQLVLVWHPL±6LVWHPL]DMDYOMDQMHYORPD±GHO =DKWHYH]DSDVLYQH
LQIUDUGHþHMDYOMDOQLNH
Alarm systems - Intrusion systems -- Part 2-2: Requirements for passive infrared
detectors
Alarmanlagen - Einbruchmeldeanlagen -- Teil 2-2: Anforderungen an Passiv-
Infrarotmelder
Systèmes d'alarme - Systèmes d'alarme intrusion -- Partie 2-2: Exigences pour
détecteurs infrarouges passifs
Ta slovenski standard je istoveten z: CLC/TS 50131-2-2:2004
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION CLC/TS 50131-2-2
SPECIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION August 2004
ICS 13.310
English version
Alarm systems - Intrusion systems
Part 2-2: Requirements for passive infrared detectors
Systèmes d'alarme - Alarmanlagen -
Systèmes de détection d'intrusion Einbruchmeldeanlagen
Partie 2-2: Exigences pour détecteurs Teil 2-2: Anforderungen an Passiv-
infrarouges passifs Infrarotmelder
This Technical Specification was approved by CENELEC on 2004-05-04.
CENELEC members are required to announce the existence of this TS in the same way as for an EN and to
make the TS available promptly at national level in an appropriate form. It is permissible to keep conflicting
national standards in force.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. CLC/TS 50131-2-2:2004 E
Foreword
This Technical Specification was prepared by the Technical Committee CENELEC TC 79, Alarm
systems.
The text of the draft was submitted to the vote at the meeting of TC 79 in Madrid and was
approved by CENELEC as CLC/TS 50131-2-2 on 2004-05-04. Standstill is maintained.
The following date was fixed:
- latest date by which the existence of the TS (doa) 2004-11-04
has to be announced at national level
NOTE Latest date by which the TS has to be voted as EN: 2 years maximum after dav of TS.
- 3 - CLC/TS 50131-2-2:2004
Contents
Page
1 Scope.4
2 Normative references.4
3 Definitions and abbreviations .4
4 Functional requirements.6
4.1 Indication signals or messages .6
4.2 Detection.7
4.3 Operational requirements .9
4.4 Immunity to incorrect operation.9
4.5 Tamper security.10
4.6 Electrical requirements .11
4.7 Environmental classification and conditions .12
5 Marking, identification and documentation .12
5.1 Marking and/or identification.12
5.2 Documentation .12
6 Testing.13
6.1 General test conditions.13
6.2 Basic detection test .14
6.3 Walk testing .14
6.4 Verification of detection performance .15
6.5 Switch-on delay, time interval between signals and indication of detection.17
6.6 Fault condition signals or messages: self tests.18
6.7 Immunity to incorrect operation.18
6.8 Tamper security.19
6.9 Electrical tests.20
6.10 Environmental classification and conditions .22
6.11 Marking, identification and documentation.23
Annex A (normative) Format of standard test magnets.24
Annex B (normative) General testing matrix.25
Annex C (normative) Walk test diagrams.27
Annex D (normative) Procedure for calculation of average temperature difference .30
Annex E (informative) Basic detection target for the basic test of detection capability .32
Annex F (informative) Calibration heat source .33
Annex G (normative) Calibration of the standard walk test target. .35
Annex H (informative) Equipment for walk test velocity control.35
Annex J (informative) Immunity to visible and near infrared radiation:
notes on calibration of the light source .36
Annex K (informative) Example list of small tools suitable for testing immunity
of casing to attack.37
Annex L (informative) Test for resistance to re-orientation of adjustable mountings.38
Figure A.1 - Format of standard test magnets.24
Figure C.1 - Detection across the boundary, & effect of control adjustments .27
Figure C.2 - Detection within the boundary, & effect of control adjustments.27
Figure C.3 - High velocity and intermittent movement .28
Figure C.4 - Close-in detection .28
Figure C.5 - Significant range reduction.29
Figure L.1 - Re-orientation test.38
Table 1 - Indication signals or messages .7
Table 2 - General walk test velocity and attitude requirements .8
Table 3 - Tamper security requirements .11
Table 4 - Electrical requirements .11
Table 5 - Range of materials for masking tests .20
Table 6 - Environmental tests, operational.23
Table 7 - Environmental tests, endurance.23
Introduction
This Technical Specification is a specification for passive infrared detectors (to be referred to as
the detector) used as part of intrusion detection systems installed in buildings. It includes four
security grades and the first three environmental classes.
The purpose of a detector is to detect the broad spectrum infrared radiation emitted by an intruder
and to provide the necessary range of signals or messages to be used by the rest of the intruder
alarm system.
The number and scope of these signals or messages will be more comprehensive for systems that
are specified at the higher grades.
This specification is only concerned with the requirements and tests for the detector. Other types
of detector are covered by other documents identified as CLC/TS 50131-2-x.
The requirement in EN 50131-1 that detectors in grade 3 and 4 systems shall include a means to
detect a significant reduction in range may be met either by detectors having the appropriate
function (4.2.3) or by suitable system design.
1 Scope
This Technical Specification provides for security grades 1 to 4 (see EN 50131-1), specific or non-
specific wired or wire-free detectors, and uses environmental classes I to III (see EN 50130-5).
A function designated in the specification as not required for a particular grade may be provided
by the manufacturer. If provided, it will be tested, and shall meet all relevant requirements of any
higher grade. If it passes, the manufacturer may claim it as an extra feature, which does not alter
the overall grading of the detector.
The specification does not apply to system interconnections.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of the
referenced document (including any amendments) applies.
EN 50130-4:1995 Alarm systems - Part 4: Electromagnetic compatibility - Product family
standard: Immunity requirements for components of fire, intruder and
social alarm systems
EN 50130-5:1998 Alarm systems - Part 5: Environmental test methods
EN 50131-1:1997 Alarm Systems - Intrusion systems - Part 1: General requirements
EN 50131-6:1997 Alarm systems - Intrusion systems - Part 6: Power supplies
EN 60529:1991 Degree of protection provided by enclosures (IP code)
3 Definitions and abbreviations
For the purpose of this specification, the following definitions and abbreviations apply in addition
to those given in EN 50131-1.
3.1
alert/set mode
state of operation in which a detector shall generate an intrusion signal or message in response to
stimulation by a human being or the standard walk test target
3.2
basic detection target
heat source designed to verify the operation of a detector
- 5 - CLC/TS 50131-2-2:2004
3.3
ceiling mount detector
detector capable of sensing human movement from a mounting position on the ceiling
3.4
curtain detector
detector capable of sensing human movement through a continuous layer of detection zones
3.5
incorrect operation
physical condition that causes an inappropriate signal or message from a detector
3.6
local memory
storage medium situated on board the detector, having the capability to record signals or
messages generated by the detector
3.7
long range detector
detector capable of sensing human movement in an extended field of view with horizontal angular
coverage less than 10°
3.8
masking
interference with the detector input capability by the introduction of a physical barrier such as
metal, plastics, paper or sprayed paints or lacquers in close proximity to the detector
3.9
passive infrared detector
detector of the broad-spectrum infrared radiation emitted by a human being
3.10
simulated walk test target
non-human or synthetic heat source designed to simulate the standard walk test target
3.11
standard walk test target
human being of standard weight and height clothed in close fitting clothing appropriate to the
simulation of an intruder
3.12
standby/unset mode
state of operation in which a detector is not required to generate an alarm signal or message in
response to stimulation by a human being or a standard walk test target
3.13
test mode
state of operation in which a detector will activate an intrusion indicator in response to stimulation
by a human being or the standard walk test target
3.14
volumetric detector
detector capable of sensing human movement in a volume such as a room with a field of view with
horizontal angular coverage greater than 45°
3.15
walk test
operational test during which a detector is stimulated by the standard walk test target in a
controlled environment
3.16
walk test attitude, crawling
crawling attitude shall consist of the standard walk test target moving with hands and knees in
contact with the floor
3.17
walk test attitude, upright
upright attitude shall consist of the standard walk test target standing and walking with arms by
the sides of the body. The standard walk test target begins and ends a traverse with feet toget
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.