iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

CLC/TS 50131-11:2012/IS1:2014

Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices

Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices

This Technical Specification is for dedicated hold-up devices in buildings, e.g. deliberately operated hold-up devices which can be triggered to create a hold-up alarm signal or message. It provides four security Grades 1-4 (see EN 50131-1), specific or non specific wired or wire-free hold-up devices and uses Environmental Classes I-IV (see EN 50130-5). This Technical Specification does not include requirements for hold-up devices intended for use outdoors, or for mobile hold-up devices or for devices with functions additional to hold-up facility. NOTE If a device provides functions additional to hold-up facility, it is recommended to function similar to the requirement described in this Technical Specification. Functions additional to the mandatory functions as specified in this Technical Specification may be included in the hold-up device, providing they do not adversely influence the correct operation of the mandatory functions. This Technical Specification does not apply to system interconnections.

Alarmanlagen - Einbruch- und Überfallmeldeanlagen - Teil 11: Anforderungen an Überfallmelder

Systèmes d’alarme - Systèmes d'alarme contre l’intrusion et les hold-up - Partie 11: Exigences pour bouton anti-agression

Alarmni sistemi - Sistemi za javljanje vloma in ropa - 11. del: Zahteve za javljalnike ropa - Dopolnilo IS1

Ta tehnična specifikacija je namenjena namenskim napravam za javljanje vloma v objektih, npr. namerno upravljane naprave za javljanje vloma, ki lahko ob sprožitvi proizvedejo alarm ali sporočilo o vlomu. Določa štiri varnostne razrede 1–4 (glejte standard EN 50131-1), specifične ali nespecifične ožičene ali brezžične naprave za javljanje vloma ter uporablja okoljske razrede I–IV (glejte standard EN 50130-5). Ta tehnična specifikacija ne zajema zahtev za naprave za javljanje vloma, ki so namenjene za uporabo na prostem, ali za mobilne naprave za javljanje vloma ali za naprave, ki poleg funkcije javljanja vloma vključujejo še druge funkcije. OPOMBA: Če naprava poleg funkcije javljanja vloma zagotavlja dodatne funkcije, je priporočeno, da deluje na način, ki je podoben zahtevi iz te tehnične specifikacije. Poleg obveznih funkcij, ki so opredeljene v tej tehnični specifikaciji, ima lahko naprava za javljanje vloma tudi dodatne funkcije, pri čemer te ne smejo neugodno vplivati na pravilno delovanje obveznih funkcij. Ta tehnična specifikacija se ne uporablja za povezave sistema.

General Information

Status
Published
Publication Date
27-Feb-2014
ICS
13.310 - Protection against crime
Technical Committee
CLC/TC 79 - Alarm systems
Current Stage
6060 - Document made available - Publishing
Start Date
28-Feb-2014
Completion Date
28-Feb-2014
Ref Project
SIST-TS CLC/TS 50131-11:2012/IS1:2014 - Alarm systems - Intrusion and hold-up systems -- Part 11: Hold-up devices

Relations

Revises
CLC/TS 50131-11:2012 - Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices
Effective Date
29-Jan-2023

Buy Standard

TS CLC/TS 50131-11:2012/IS1:2014TS CLC/TS 50131-11:2012/IS1:2014
PreviousNext
Addendum
TS CLC/TS 50131-11:2012/IS1:2014
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2014
Alarmni sistemi - Sistemi za javljanje vloma in ropa - 11. del: Zahteve za javljalnike
ropa - Dopolnilo IS1
Alarm systems - Intrusion and hold-up systems -- Part 11: Hold-up devices
Alarmanlagen - Einbruch- und Überfallmeldeanlagen -- Teil 11: Anforderungen an
Überfallmelder
Systèmes d’alarme - Systèmes d'alarme contre l’intrusion et les hold-up -- Partie 11:
Exigences pour bouton anti-agression
Ta slovenski standard je istoveten z: CLC/TS 50131-11:2012/IS1:2014
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERPRETATION SHEET
CLC/TS 50131-11/IS1
FEUILLE D'INTERPRETATION
February 2014
INTERPRETATIONSBLATT
ICS 13.310
English version
Alarm systems -
Intrusion and hold-up systems -
Part 11: Hold-up devices
Systèmes d’alarme -  Alarmanlagen -
Systèmes d'alarme contre l’intrusion et les Einbruch- und Überfallmeldeanlagen -
hold-up - Teil 11: Anforderungen an Überfallmelder
Partie 11: Exigences pour bouton anti-
agression
This Technical Specification was approved by CENELEC on 2013-12-23.

CENELEC members are required to announce the existence of this TS in the same way as for an EN and to
make the TS available promptly at national level in an appropriate form. It is permissible to keep conflicting
national standards in force.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2014 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. CLC/TS 50131-11:2012/IS1:2014 E

Contents Page
Foreword . 3
Clause: . 4
Question: . 4
Interpretation: . 4
Validity: . 4

Foreword
This Interpreta
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50131-2-2:2021(Main)
Alarm systems - Intrusion and hold-up systems - Part 2-2: Requirements for passive infrared detectors
SIST EN 50131-2-2:2022

This document is for passive infrared detectors installed in buildings and provides for security grades 1 to 4 (see EN 50131 1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see EN 50130 5). This document does not include requirements for detectors intended for use outdoors. The purpose of the detector is to detect the broad spectrum infrared radiation emitted by an intruder, to analyse the resulting signals and to provide the necessary range of signals or messages to be used by the rest of the intrusion alarm system. The grade-dependent requirements of this document apply and it is essential that a detector fulfils all the requirements of the specified grade. Functions additional to the mandatory functions specified in this document can be included in the detector, providing they do not influence the correct operation of the mandatory functions. Requirements for system interconnections are not included in this document.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-6:2017/A1:2021(Amendment)
Alarm systems - Intrusion and hold-up systems - Part 6: Power supplies
SIST EN 50131-6:2018/A1:2021

This European Standard specifies the requirements, performance criteria and testing procedures for PS to be used as part of Intrusion and Hold up Alarm Systems. The PS will either be an integral part of an I&HAS component or stand-alone. The control functions of the PS may be incorporated as part of the PS device, or may be provided by another I&HAS component, e.g. a CIE. This European Standard is not applicable when the PS requirements for I&HAS components are included within the relevant product standard. The requirements correspond to each of the four security grades given in the European Standard EN 50131 1, Alarm Systems – Intrusion and Hold-Up Systems - Part 1: System requirements. Requirements are also given for four environmental classes covering applications in indoor and outdoor locations. This standard covers: a) mandatory functions which will be provided on all PS; and b) optional functions which may be provided. This European Standard does not deal with requirements for compliance with EC regulatory Directives, such as the EMC Directive, Low Voltage Directive, etc. except that it specifies the equipment operating conditions and reduced functional test for EMC susceptibility testing as required by EN 50130 4. Other functions associated with I&HAS not specified in this standard may be provided. Such functions will not affect the requirements of any mandatory or optional functions.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-2-4:2020(Main)
Alarm systems - Intrusion and hold-up systems - Part 2-4: Requirements for combined passive infrared and microwave detectors
SIST EN 50131-2-4:2020

This document is for combined passive infrared and microwave detectors installed in buildings and provides for security grades 1 to 4 (see EN 50131-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see EN 50130-5). This document does not include requirements for detectors intended for use outdoors. The purpose of the detector is to detect the broad spectrum infrared radiation emitted by an intruder, to emit microwave signals and analyse the signals that are returned and to provide the necessary range of signals or messages to be used by the rest of the intrusion alarm system. For a combined detector where both detection technologies need to be in their activated state in order to generate an alarm condition, the grade-dependent requirements of this document apply. For combined detectors which can be configured or operated such that each detection technology can generate an alarm condition independently, the grade-dependant requirements as defined in EN 50131 2 2 and EN 50131-2-3 apply, when configured accordingly. Otherwise, it is the responsibility of the manufacturer to clearly state that the detector does not comply to this document and not to EN 50131-2-2 and EN 50131 2-3 when put into such a configuration. It is essential that a detector fulfils all the requirements of the specified grade. Functions additional to the mandatory functions specified in this document can be included in the detector, providing they do not influence the correct operation of the mandatory functions. Requirements for system interconnections are not included in this document.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-1:2006/A3:2020(Amendment)
Alarm systems - Intrusion and hold-up systems - Part 1: System requirements
SIST EN 50131-1:2007/A3:2020

This European Standard specifies the requirements for Intrusion and Hold-up Alarm Systems installed in buildings using specific or non-specific wired interconnections or wire-free interconnections. These requirements also apply to the components of an I&HAS installed in a building which are normally mounted on the external structure of a building e.g. ancillary control equipment or warning devices. The standard does not include requirements for exterior I&HAS. This standard specifies performance requirements for installed I&HAS but does not include requirements for design, planning, installation, operation or maintenance. These requirements also apply to I&HAS sharing means of detection, triggering, interconnection, control, communication and power supplies with other applications. The functioning of an I&HAS shall not be adversely influenced by other applications. Requirements are specified for I&HAS components where the relevant environment is classified. This classification describes the environment in which an I&HAS component may be expected to function as designed. When the requirements of the four environmental classes are inadequate, due to the extreme conditions experienced in certain geographic locations, special national conditions are given in Annex A. General environmental requirements for I&HAS components are described in Clause 7. The requirements of this European Standard also apply to IAS and HAS when these systems are installed independently. When an I&HAS does not include functions relating to the detection of intruders, the requirements relating to intrusion detection do not apply. When an I&HAS does not include functions relating to hold-up, the requirements relating to hold-up do not apply. NOTE Unless otherwise stated the abbreviation I&HAS is intended to also mean IAS and HAS.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-6:2017(Main)
Alarm systems - Intrusion and hold-up systems - Part 6: Power supplies
SIST EN 50131-6:2018

This European Standard specifies the requirements, performance criteria and testing procedures for PS to be used as part of Intrusion and Hold up Alarm Systems. The PS will either be an integral part of an I&HAS component or stand-alone. The control functions of the PS may be incorporated as part of the PS device, or may be provided by another I&HAS component, e.g. a CIE. This European Standard is not applicable when the PS requirements for I&HAS components are included within the relevant product standard. The requirements correspond to each of the four security grades given in the European Standard EN 50131 1, Alarm Systems - Intrusion and Hold-Up Systems - Part 1: System requirements. Requirements are also given for four environmental classes covering applications in indoor and outdoor locations. This standard covers: a) mandatory functions which will be provided on all PS; and b) optional functions which may be provided. This European Standard does not deal with requirements for compliance with EC regulatory Directives, such as the EMC Directive, Low Voltage Directive, etc. except that it specifies the equipment operating conditions and reduced functional test for EMC susceptibility testing as required by EN 50130 4. Other functions associated with I&HAS not specified in this standard may be provided. Such functions will not affect the requirements of any mandatory or optional functions.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-1:2006/A2:2017(Amendment)
Alarm systems - Intrusion and hold-up systems - Part 1: System requirements
SIST EN 50131-1:2007/A2:2017

Harmonise system requirements with requirements for system components specified in standard published since EN 50131-1:2006 was published.

  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-5-3:2017(Main)
Alarm systems - Intrusion systems - Part 5-3: Requirements for interconnections equipment using radio frequency techniques
SIST EN 50131-5-3:2017

This European Standard applies to intrusion alarm equipment using radio frequency (RF) links and located on protected premises. It does not cover long-range radio transmissions. This European Standard defines the terms used in the field of intrusion alarm equipment using radio frequency links as well as the requirements relevant to the equipment.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
CLC/TS 50131-11:2012(Main)
Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices
SIST-TS CLC/TS 50131-11:2012

This Technical Specification is for dedicated hold-up devices in buildings, e.g. deliberately operated hold-up devices which can be triggered to create a hold-up alarm signal or message. It provides four security Grades 1-4 (see EN 50131-1), specific or non specific wired or wire-free hold-up devices and uses Environmental Classes I-IV (see EN 50130-5). This Technical Specification does not include requirements for hold-up devices intended for use outdoors, or for mobile hold-up devices or for devices with functions additional to hold-up facility. NOTE If a device provides functions additional to hold-up facility, it is recommended to function similar to the requirement described in this Technical Specification. Functions additional to the mandatory functions as specified in this Technical Specification may be included in the hold-up device, providing they do not adversely influence the correct operation of the mandatory functions. This Technical Specification does not apply to system interconnections.

  • Technical specification
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-1:2006/IS2:2010
Alarm systems - Intrusion and hold-up systems - Part 1: System requirements
SIST EN 50131-1:2007/IS2:2011

This European Standard specifies the requirements for Intrusion and Hold-up Alarm Systems installed in buildings using specific or non-specific wired interconnections or wire-free interconnections. These requirements also apply to the components of an I&HAS installed in a building which are normally mounted on the external structure of a building e.g. ancillary control equipment or warning devices. The standard does not include requirements for exterior I&HAS. This standard specifies performance requirements for installed I&HAS but does not include requirements for design, planning, installation, operation or maintenance. These requirements also apply to I&HAS sharing means of detection, triggering, interconnection, control, communication and power supplies with other applications. The functioning of an I&HAS shall not be adversely influenced by other applications. Requirements are specified for I&HAS components where the relevant environment is classified. This classification describes the environment in which an I&HAS component may be expected to function as designed. When the requirements of the four environmental classes are inadequate, due to the extreme conditions experienced in certain geographic locations, special national conditions are given in Annex A. General environmental requirements for I&HAS components are described in Clause 7. The requirements of this European Standard also apply to IAS and HAS when these systems are installed independently. When an I&HAS does not include functions relating to the detection of intruders, the requirements relating to intrusion detection do not apply. When an I&HAS does not include functions relating to hold-up, the requirements relating to hold-up do not apply. NOTE Unless otherwise stated the abbreviation I&HAS is intended to also mean IAS and HAS.

  • Addendum
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50131-5-3:2005/IS1:2010
Alarm systems - Intrusion systems - Part 5-3: Requirements for interconnections equipment using radio frequency techniques
SIST EN 50131-5-3:2005/IS1:2011

This European Standard applies to intrusion alarm equipment using radio frequency (RF) links and located on protected premises. It does not cover long range radio transmissions. This standard defines the terms used in the field of intrusion alarm equipment using radio frequency links as well as the requirements relevant to the equipment. It shall be used in conjunction with the other parts of the EN 50131 series that define the functional requirements of the equipment regardless of the type of interconnections used.

  • Addendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day