HD 60269-2:2010

Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to J

IEC 60269-2:2010 provides fuses for use by authorized persons are generally designed to be used in installations where the fuse-links are accessible to, and may be replaced by, authorized persons only. This standard is divided into fuse systems,(A thru I), each dealing with a specific example of standardized fuses for use by authorized persons. This fourth edition of IEC 60269-2 cancels and replaces the third edition published in 2006 and constitutes a minor revision. This part is to be used in conjunction with IEC 60269-1:2006, Low-voltage fuses - Part 1: General requirements and its Amendment 1 (2009). This Part 2 supplements or modifies the corresponding clauses or subclauses of Part 1. Where no change is necessary, this Part 2 indicates that the relevant clause or subclause applies. Tables and figures which are additional to those in Part 1 are numbered starting from 101. Additional annexes are numbered AA, BB, etc.

Niederspannungssicherungen - Teil 2: Zusätzliche Anforderungen an Sicherungen zum Gebrauch durch Elektrofachkräfte bzw. elektrotechnisch unterwiesene Personen (Sicherungen überwiegend für den industriellen Gebrauch) - Beispiele für genormte Sicherungssysteme A bis J

Fusibles basse tension - Partie 2: Exigences supplémentaires pour les fusibles destinés à être utilisés par des personnes habilitées (fusibles pour usages essentiellement industriels) - Exemples de systèmes de fusibles normalisés A à J

La CEI 60269-2:2010 donne les fusibles destinés à être utilisés par des personnes habilitées sont généralement conçus pour usage dans des installations où les éléments de remplacement ne sont accessibles qu'à des personnes habilitées, et ne peuvent être remplacés que par elles. Cette quatrième édition de la CEI 60269-2 annule et remplace la troisième édition parue en 2006 et constitue une révision mineure. La présente partie doit être utilisée conjointement avec la CEI 60269-1:2006, Fusibles basse tension - Partie 1: Exigences générales et son Amendement 1 (2009). Cette Partie 2 complète ou modifie les articles ou paragraphes correspondant de la Partie 1. Lorsqu'aucune modification n'est nécessaire, la Partie 2 indique que l'article ou le paragraphe approprié est applicable. Les tableaux et les figures qui sont complémentaires à ceux de la Partie 1 sont numérotés à partir de 101. Les annexes complémentaires sont numérotées AA, BB, etc.

Nizkonapetostne varovalke - 2. del: Dodatne zahteve za varovalke, ki jih uporabljajo strokovne osebe (uporaba varovalk zlasti v industriji) - Primeri tipov standardiziranih varovalk od A do J (IEC 60269-2:2010, spremenjen)

Varovalke, ki jih uporabljajo strokovne osebe, so običajno zasnovane za uporabo pri napeljavah, kjer so vložki varovalk dosegljivi zgolj strokovnim osebam, ki jih tudi edine lahko menjavajo. Varovalke, ki jih uporabljajo strokovne osebe in so v skladu z naslednjimi sistemi varovalk, so prav tako v skladu z zahtevami ustreznimi podklavzulami IEC 60269-1, razen če je v tem standardu drugače opredeljeno. Ta standard je razdeljen na sisteme varovalk, pri čemer vsak obravnava določen primer standardiziranih varovalk, ki jih uporabljajo strokovne osebe:
Sistem varovalk A: varovalke z vložki z nožastimi kontakti (NH sistem varovalk).
Sistem varovalk B: varovalke z zapiralnimi vložki z nožastimi kontakti (NH sistem varovalk).
Sistem varovalk C: zapahi v varovalkah (NH sistem varovalk).
Sistem varovalk D: osnove varovalk za namestitev zbiralke (NH sistem varovalk).
Sistem varovalk E: varovalke z vložki za vijačne spoje (BS vijačni sistem varovalk).
Sistem varovalk F: varovalke z vložki, ki imajo cilindrične kontaktne kapice (NF sistem cilindričnih varovalk).
Sistem varovalk G: varovalke z vložki z stranskimi nožastimi kontakti (BS sistem varovalk).
Sistem varovalk H: varovalke z vložki, ki imajo »gD« in gN« značilnosti (razred J in časovna zakasnitev razreda L in vrste varovalk brez časovne zakasnitve).
Sistem varovalk I: gU vložki varovalk s kontakti za zategovanje z zagozdo.
Sistem varovalk J: varovalke z vložki, ki imajo značilnosti »gD razreda CC« in »gN razreda CC« (časovna zakasnitev razreda CC in vrste varovalk brez časovne zakasnitve).
OPOMBA: Zgoraj navedeni sistemi varovalk so glede na njihovih varstvene vidike standardizirani sistemi. Nacionalni odbori lahko izberejo med primeri standardiziranih varovalk enega ali več sistemov za svoje lastne standarde.

General Information

• Status: Withdrawn
• Publication Date: 16-Sep-2010
• Withdrawal Date: 31-Aug-2013
• ICS: 29.120.50 - Fuses and other overcurrent protection devices
• Technical Committee: CLC/SR 32B - Low-voltage fuses
• Drafting Committee: IEC/SC 32B - IEC_SC_32B
• Parallel Committee: IEC/SC 32B - IEC_SC_32B
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-Aug-2016
• Completion Date: 15-Aug-2016
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: SIST HD 60269-2:2010 - Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to J (IEC 60269-2:2010, modified)

Relations

• Replaces: HD 60269-2:2007 - Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to J
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2010
1DGRPHãþD
SIST HD 60269-2:2008
Nizkonapetostne varovalke - 2. del: Dodatne zahteve za varovalke, ki jih
uporabljajo strokovne osebe (uporaba varovalk zlasti v industriji) - Primeri tipov
standardiziranih varovalk od A do J (IEC 60269-2:2010, spremenjen)
Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized
persons (fuses mainly for industrial application) - Examples of standardized systems of
fuses A to J (IEC 60269-2:2010, modified)
Niederspannungssicherungen - Teil 2: Zusätzliche Anforderungen an Sicherungen zum
Gebrauch durch Elektrofachkräfte bzw. elektrotechnisch unterwiesene Personen
(Sicherungen überwiegend für den industriellen Gebrauch) - Beispiele für genormte
Sicherungssysteme A bis J (IEC 60269-2:2010, modifiziert)
Fusibles basse tension - Partie 2: Exigences supplémentaires pour les fusibles destinés
à être utilisés par des personnes habilitées (fusibles pour usages essentiellement
industriels) - Exemples de systèmes de fusibles normalisés A à J (IEC 60269-2:2010,
modifiée)
Ta slovenski standard je istoveten z: HD 60269-2:2010
ICS:
29.120.50 9DURYDONHLQGUXJD Fuses and other overcurrent
PHGWRNRYQD]DãþLWD protection devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

HARMONIZATION DOCUMENT
HD 60269-2
DOCUMENT D'HARMONISATION
September 2010
HARMONISIERUNGSDOKUMENT
ICS 29.120.50 Supersedes HD 60269-2:2007

English version
Low-voltage fuses -
Part 2: Supplementary requirements for fuses for use by authorized
persons (fuses mainly for industrial application) -
Examples of standardized systems of fuses A to J
(IEC 60269-2:2010, modified)
Fusibles basse tension -  Niederspannungssicherungen -
Partie 2: Exigences supplémentaires pour Teil 2: Zusätzliche Anforderungen
les fusibles destinés à être utilisés par an Sicherungen zum Gebrauch durch
des personnes habilitées (fusibles pour Elektrofachkräfte bzw. elektrotechnisch
usages essentiellement industriels) - unterwiesene Personen (Sicherungen
Exemples de systèmes de fusibles überwiegend für den industriellen
normalisés A à J Gebrauch) - Beispiele für genormte
(CEI 60269-2:2010, modifiée) Sicherungssysteme A bis J
(IEC 60269-2:2010, modifiziert)

This Harmonization Document was approved by CENELEC on 2010-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for implementation of this
Harmonization Document at national level.

Up-to-date lists and bibliographical references concerning such national implementations may be obtained on
application to the Central Secretariat or to any CENELEC member.

This Harmonization Document exists in three official versions (English, French, German).

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. HD 60269-2:2010 E
Foreword
The text of document 32B/552/FDIS, future edition 4 of IEC 60269-2, prepared by SC 32B, Low-voltage
fuses, of IEC TC 32, Fuses, was submitted to the IEC-CENELEC parallel vote.
A draft amendment, containing common modifications to document 32B/552/FDIS was prepared by
Reporting Secretariat CLC/SR 32B, Low-voltage fuses, and was submitted to the formal vote.
The combined texts were approved by CENELEC as HD 60269-2 on 2010-09-01.
This Harmonization Document supersedes HD 60269-2:2007
This document is to be used in conjunction with EN 60269-1:2007.
This Part 2 supplements or modifies the corresponding clauses or subclauses of Part 1.
Where no change is necessary, this Part 2 indicates that the relevant clause or subclause applies.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-09-01
Annex ZA has been added by CENELEC.
__________
- 3 - HD 60269-2:2010
Endorsement notice
The text of the International Standard IEC 60269-2:2010 was approved by CENELEC as a Harmonization
Document with agreed common modifications as given below.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60060-2 NOTE  Harmonized as EN 60060-2.
IEC 60060-3 NOTE  Harmonized as EN 60060-3.
IEC 60529 NOTE  Harmonized as EN 60529.
ISO 898-1 NOTE  Harmonized as EN ISO 898-1.
ISO 1207:1992 NOTE  Harmonized as EN ISO 1207:1994 (not modified).

COMMON MODIFICATIONS
1 General scope
Replace the note by:
NOTE The following fuse systems are standardized systems in respect to their safety aspects. The National Committees shall
select at least one complete fuse system of this standard for their national standards. The time current characteristics "gD" and "gN"
are only relevant for the fuse system H.
Fuse system A – Fuses with fuse-links with blade contacts (NH fuse system)
6.2 Marking of fuse-links
Replace the first sentence after the table by the following:
Fuse-links with isolated gripping-lugs shall be marked in a place visible at the front with the graphical
symbol of a gripping-lug in a square.
8.5.5.1 Verification of the peak withstand current of a fuse-base
Add at the end of the first sentence:
... or if the minimum withdrawal forces according to 8.11 are exceeded.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60060-1 - High-voltage test techniques - HD 588.1 S1 -
Part 1: General definitions and test
requirements
IEC 60112 - Method for the determination of the proof EN 60112 -
and the comparative tracking indices of solid
insulating materials
IEC 60269-1 2006 Low-voltage fuses - EN 60269-1 2007
+ A1 2009 Part 1: General requirements + A1 2009

IEC 60664-1 - Insulation coordination for equipment within EN 60664-1 -
low-voltage systems -
Part 1: Principles, requirements and tests

IEC 60999 Series Connecting devices - Electrical copper EN 60999 Series
conductors - Safety requirements for screw-
type and screwless-type clamping units

IEC 60999-1 - Connecting devices - Electrical copper EN 60999-1 -
conductors - Safety requirements for screw-
type and screwless-type clamping units -
Part 1: General requirements and particular
requirements for clamping units for conductors
from 0,2 mm² up to 35 mm² (included)

IEC 60999-2 - Connecting devices - Electrical copper EN 60999-2 -
conductors - Safety requirements for screw-
type and screwless-type clamping units -
Part 2: Particular requirements for clamping
units for conductors above 35 mm² up to
300 mm² (included)
ISO 6988 - Metallic and other non-organic coatings - EN ISO 6988 -
Sulfur dioxide test with general condensation
of moisture
IEC 60269-2 ®
Edition 4.0 2010-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Low-voltage fuses –
Part 2: Supplementary requirements for fuses for use by authorized persons
(fuses mainly for industrial application) – Examples of standardized systems of
fuses A to J
Fusibles basse tension –
Partie 2: Exigences supplémentaires pour les fusibles destinés à être utilisés
par des personnes habilitées (fusibles pour usages essentiellement industriels)
– Exemples de systèmes de fusibles normalisés A à J

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
XJ
CODE PRIX
ICS 29.120.50 ISBN 978-2-88910-087-3
– 2 – 60269-2 © IEC:2010
CONTENTS
FOREWORD.14
INTRODUCTION.16
1 General scope .17
1.2 Normative references .18

Fuse system A – Fuses with fuse-links with blade contacts (NH fuse system) .19
1 General .19
1.1 Scope.19
2 Terms and definitions .19
3 Conditions for operation in service.19
4 Classification.20
5 Characteristics of fuses .20
5.2 Rated voltage.20
5.3.1 Rated current of the fuse-link.20
5.3.2 Rated current of the fuse-holder .20
5.5 Rated power dissipation of a fuse-link and rated acceptable power
dissipation of a fuse-holder .20
5.6 Limits of time-current characteristics .21
5.6.1 Time-current characteristics, time-current zones and overload curves .21
5.6.2 Conventional times and currents.21
5.6.3 Gates .21
5.7.2 Rated breaking capacity .21
6 Marking .22
6.1 Markings of fuse-holders .22
6.2 Markings of fuse-links.22
7 Standard conditions for construction.22
7.1 Mechanical design.23
7.1.2 Connections, including terminals .23
7.1.3 Fuse-contacts.23
7.1.6 Construction of fuse-bases .23
7.1.7 Construction of a fuse-link .24
7.2 Insulating properties.24
7.7 I t characteristics .24
7.8 Overcurrent discrimination of "gG" fuse-links.25
7.9 Protection against electric shock .25
8 Tests .25
8.1.4 Arrangement of the fuse and dimensions .26
8.1.6 Testing of fuse-holders .26
8.2.4 Acceptability of test results.27
8.2.5 Resistance to tracking .27
8.3 Verification of temperature rise and power dissipation.27
8.3.1 Arrangement of the fuse .27
8.3.2 Measurement of the temperature rise .28
8.5.8 Acceptability of test results.29
8.7.4 Verification of overcurrent discrimination .29

60269-2 © IEC:2010 – 3 –
8.9 Verification of resistance to heat .31
8.9.1 Fuse-base .
...