Optical circuit boards - Basic test and measurement procedures - Part 2-5: Flexibility test for flexible opto-electric circuits

This part of IEC 62496-2 defines a test method for folding flexibility inspection of flexible opto-electric circuits with a MIT folding endurance tester and presents a guideline for a step stress test method for finding the predetermined minimum mechanical folding radii below which the flexible opto-electric circuits can be damaged by intended folding distortion. Here, test samples are used instead of products for the flexibility test of their flexible opto-electric circuits, and the test samples have the same layer structure as the products.

Optische Leiterplatten - Grundlegende Prüf- und Messverfahren - Teil 2-5: Biegsamkeitstest für biegsame opto-elektrische Schaltkreise

Cartes à circuits optiques - Procédures fondamentales d’essais et de mesures - Partie 2-5: Essai de flexibilité pour les circuits optoélectriques souples

IEC 62496-2-5:2022 définit une méthode d’essai pour l’examen de la flexibilité au pliage des circuits optoélectriques souples au moyen d’un appareil de contrôle de la flexibilité, et fournit un guide qui présente une méthode d’essai sous contrainte échelonnée destinée à déterminer les rayons de pliage mécanique minimaux prédéterminés en deçà desquels les circuits optoélectriques souples peuvent être endommagés par la distorsion induite par un pliage intentionnel. Des échantillons d’essai sont utilisés ici à la place des produits pour l’essai de flexibilité de leurs circuits optoélectriques souples, et ces échantillons d’essai sont constitués du même matériau, ont la même structure de couches et utilisent la même technologie et les mêmes équipements de traitement que les produits eux-mêmes.

Plošče z optičnimi vezji - Osnovni preskusni in merilni postopki - 2-5. del: Preskušanje upogljivosti za zvijava optoelektrična vezja (IEC 62496-2-5:2022)

Ta del standarda IEC 62496-2 opredeljuje preskusno metodo za preskušanje upogljivosti zvijavih optoelektričnih vezij z napravo za preskušanje vzdržljivosti pregibanja MIT in predstavlja smernice za metodo stopenjskega preskusa obremenitve, da se ugotovi vnaprej določen minimalni mehanski zgibni polmer, pod katerim se zvijava optoelektrična vezja lahko poškodujejo zaradi namernega zvijanja. Tukaj se namesto izdelkov uporabljajo preskusni vzorci za preskušanje prožnosti njihovih zvijavih optoelektričnih vezij. Preskusni vzorci imajo enako strukturo plasti kot izdelki.

General Information

Status
Published
Publication Date
19-Jan-2023
Technical Committee
Drafting Committee
Current Stage
6060 - Document made available - Publishing
Start Date
20-Jan-2023
Completion Date
20-Jan-2023

Buy Standard

Standard
EN IEC 62496-2-5:2023 - BARVE
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2023
Plošče z optičnimi vezji - Osnovni preskusni in merilni postopki - 2-5. del:
Preskušanje upogljivosti za zvijava optoelektrična vezja (IEC 62496-2-5:2022)
Optical circuit boards - Basic test and measurement procedures - Part 2-5: Flexibility test
for flexible opto-electric circuits (IEC 62496-2-5:2022)
Optische Leiterplatten - Grundlegende Prüf- und Messverfahren - Teil 2-5:
Biegsamkeitstest für biegsame opto-elektrische Schaltkreise (IEC 62496-2-5:2022)
Cartes à circuits optiques - Procédures fondamentales d’essais et de mesures - Partie 2-
5: Essai de flexibilité pour les circuits optoélectriques souples (IEC 62496-2-5:2022)
Ta slovenski standard je istoveten z: EN IEC 62496-2-5:2023
ICS:
31.180 Tiskana vezja (TIV) in tiskane Printed circuits and boards
plošče
33.180.01 Sistemi z optičnimi vlakni na Fibre optic systems in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62496-2-5

NORME EUROPÉENNE
EUROPÄISCHE NORM January 2023
ICS 33.180.01
English Version
Optical circuit boards - Basic test and measurement procedures
- Part 2-5: Flexibility test for flexible opto-electric circuits
(IEC 62496-2-5:2022)
Cartes à circuits optiques - Procédures fondamentales Optische Leiterplatten - Grundlegende Prüf- und
d'essais et de mesures - Partie 2-5: Essai de flexibilité pour Messverfahren - Teil 2-5: Biegsamkeitstest für biegsame
les circuits optoélectriques souples opto-elektrische Schaltkreise
(IEC 62496-2-5:2022) (IEC 62496-2-5:2022)
This European Standard was approved by CENELEC on 2023-01-11. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62496-2-5:2023 E

European foreword
The text of document 86/605/FDIS, future edition 1 of IEC 62496-2-5, prepared by IEC/TC 86 "Fibre
optics" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-10-11
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2026-01-11
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62496-2-5:2022 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60793-2-10 NOTE Harmonized as EN IEC 60793-2-10
IEC 60793-2-20 NOTE Harmonized as EN 60793-2-20
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General EN 60068-1 -
and guidance
IEC 60793-2 series Optical fibres - Part 2: Product EN IEC 60793-2 series
specifications
IEC 62496-2-1 - Optical circuit boards - Part 2-1: EN 62496-2-1 -
Measurements - Optical attenuation and
isolation
ISO 5626 1993 Paper - determination of folding endurance - -

IEC 62496-2-5 ®
Edition 1.0 2022-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Optical circuit boards – Basic test and measurement procedures –

Part 2-5: Flexibility test for flexible opto-electric circuits

Cartes a circuits optiques – Procédures fondamentales d’essais et de mesures


Partie 2-5: Essai de flexibilité pour les circuits optoélectriques souples

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.01 ISBN 978-2-8322-6119-4

– 2 – IEC 62496-2-5:2022 © IEC 2022
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Apparatus . 7
4.1 General description . 7
4.2 Flexibility tester for flexibility test of FOECBs . 8
4.2.1 FOECBs test sample of fibre optical types . 8
4.2.2 FOECBs test sample of planer waveguide optical circuit types . 8
4.3 O-E signal control source . 9
4.4 Laser source . 9
4.5 Photo detector . 9
4.6 Folding jig . 9
4.7 Relay switch . 10
4.8 Main controller . 10
5 Test sample . 10
5.1 FOECB test samples of optical fibre-types . 10
5.2 FOECB test samples of planar optical waveguide-types . 11
6 Procedures . 13
6.1 For test samples of optical fibre-types . 13
6.1.1 Preparing test samples . 13
6.1.2 Initial optical and electrical performance measurement . 13
6.1.3 Setting the test sample . 13
6.1.4 Flexibility measurement . 14
6.1.5 Final optical and electrical performance measurement . 14
6.1.6 Mechanical performance measurement . 14
6.2 For test samples of the planar optical waveguide-types. 14
6.2.1 Preparing test samples . 14
6.2.2 Initial optical and electrical performance measurement . 14
6.2.3 Setting the test sample . 15
6.2.4 Flexibility measurement . 15
6.2.5 Final optical and electrical performance measurement . 15
6.2.6 Mechanical characteristic measurement . 16
7 Report . 16
Annex A (informative) Detail requirement for structure of FOECB test samples of
optical fibre-types . 17
Annex B (informative) Requirement for structure of FOECB test samples of planar
optical waveguide-types . 18
Annex C (informative) Guideline for flexibility folding jig setting conditions of FOECB
test samples . 19
Bibliography . 20

Figure 1 – Schematic diagram of flexible opto-electric circuit board (top view) . 7
Figure 2 – Overview of the folding jig . 8
Figure 3 – Schematic diagram of the flexibility test system for fibre optical circuits . 8

IEC 62496-2-5:2022 © IEC 2022 – 3 –
Figure 4 – Schematic diagram of the flexibility test system for planar waveguide optical
circuits . 9
Figure 5 – Flexibility folding jigs (from the left, folding radius r is 1,0 mm, 2,0 mm, 3,0

mm, 4,0 mm, 5,0 mm and 10,0 mm) . 10
Figure 6 – Schematic diagram of FOECB test samples of optical fibre-types . 11
Figure 7 – Schematic diagram of FOECB test samples of planar optical waveguide-
types. 12
Figure B.1 – Schematic diagram of the flexibility test system for planar waveguide
optical circuits . 18
Figure C.1 – An example of measurement result of optical loss versus bending
diameter . 19

– 4 – IEC 62496-2-5:2022 © IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OPTICAL CIRCUIT BOARDS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-5: Flexibility test for flexible opto-electric circuits

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collabor
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.