EN IEC 62282-5-100:2018
(Main)Fuel cell technologies - Part 5-100: Portable fuel cell power systems - Safety
Fuel cell technologies - Part 5-100: Portable fuel cell power systems - Safety
IEC 62282-5-100:2018 covers construction, marking and test requirements for portable fuel cell power systems. These fuel cell systems are movable and not fastened or otherwise secured to a specific location. The purpose of the portable fuel cell power system is to produce electrical power. This document applies to AC and DC type portable fuel cell power systems, with a rated output voltage not exceeding 600 V AC, or 850 V DC for indoor and outdoor use.
Brennstoffzellentechnologien - Teil 5-100: Portable Brennstoffzellen-Energiesysteme - Sicherheit
Technologies des piles à combustible - Partie 5-100: Systèmes à piles à combustible portables - Sécurité
L’IEC 62282-5-100:2018 couvre les exigences de construction, de marquage et d'essai des systèmes à piles à combustible portables. Ces systèmes à piles à combustible sont mobiles et ne sont ni attachés ni fixés par un autre moyen à un emplacement spécifique. Un système à pile à combustible portable est destiné à produire une puissance électrique. Le présent document s'applique aux systèmes à piles à combustible portables à courant alternatif et à courant continu dont la tension de sortie assignée ne dépasse pas 600 V en courant alternatif ou 850 V en courant continu et qui sont destinés à un usage à l'intérieur et à l'extérieur.
Tehnologije gorivnih celic - 5-100. del: Naprave s prenosnimi gorivnimi celicami - Varnost (IEC 62282-5-100:2018)
Ta del standarda IEC 62282 zajema zahteve za gradnjo, označevanje in preskušanje naprav s prenosnimi gorivnimi celicami. Ti sistemi z gorivnimi celicami so premični in niso pritrjeni ali drugače nameščeni na določeni lokaciji. Naprave s prenosnimi gorivnimi celicami so namenjene proizvodnji električne energije.
Ta dokument se uporablja za notranje ali zunanje naprave s prenosnimi gorivnimi celicami z izmenično ali enosmerno napetostjo, katerih nazivna izhodna efektivna napetost je manjša od 600 V izmenično ali 850 V enosmerno. Te naprave s prenosnimi gorivnimi celicami se ne smejo uporabljati na nevarnih lokacijah iz standardov IEC 60050-426:2008, 426-03-01, razen če se sprejmejo dodatni zaščitni ukrepi v skladu s standardom IEC 60079-0[5]1.
Ta dokument se ne uporablja za naprave s prenosnimi gorivnimi celicami, ki so trajno priključene na sistem
1) za distribucijo električne energije,
2) ki so trajno priključene na sistem za distribucijo goriva,
3) ki izvaža električno energijo v omrežje,
4) za pogon cestnih vozil,
5) za uporabo na potniških letalih.
Gorivne celice, ki omogočajo polnjenje akumulatorja hibridnih vozil, pri katerih akumulator zagotavlja električno energijo za pogon vozila, ne spadajo na področje uporabe tega dokumenta. Na področje uporabe tega dokumenta spadajo naslednja goriva in energenti:
• zemeljski plin,
• utekočinjeni naftni plini, kot sta propan in butan,
• tekoči alkoholi, npr. metanol, etanol,
• bencin,
• dizelsko gorivo,
• kerozin,
• vodik,
• kemični hidridi.
Ta dokument ne izključuje uporabe podobnih goriv ali oksidantov iz drugih virov razen zraka, če se posebne nevarnosti obravnavajo v dodatnih zahtevah.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2018
1DGRPHãþD
SIST EN 62282-5-1:2013
Tehnologije gorivnih celic - 5-100. del: Naprave s prenosnimi gorivnimi celicami -
Varnost (IEC 62282-5-100:2018)
Fuel cell technologies - Part 5-100: Portable fuel cell power systems - Safety (IEC 62282
-5-100:2018)
Ta slovenski standard je istoveten z: EN IEC 62282-5-100:2018
ICS:
27.070 Gorilne celice Fuel cells
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62282-5-100
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2018
ICS 27.070 Supersedes EN 62282-5-1:2012
English Version
Fuel cell technologies - Part 5-100: Portable fuel cell power
systems - Safety
(IEC 62282-5-100:2018)
Technologies des piles à combustible - Partie 5-100: Brennstoffzellentechnologien - Teil 5-100: Portable
Systèmes à piles à combustible portables - Sécurité Brennstoffzellen-Energiesysteme - Sicherheit
(IEC 62282-5-100:2018) (IEC 62282-5-100:2018)
This European Standard was approved by CENELEC on 2018-05-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62282-5-100:2018 E
European foreword
The text of document 105/649/CDV, future edition 1 of IEC 62282-5-100, prepared by IEC/TC 105
"Fuel cell technologies" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC
as EN IEC 62282-5-100:2018.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-02-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2021-05-17
document have to be withdrawn
This document supersedes EN 62282-5-1:2012
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62282-5-100:2018 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60079 series NOTE Harmonized as EN IEC 60079 series
IEC 60079-0 NOTE Harmonized as EN IEC 60079-0
ISO/IEC 80079-20-1 NOTE Harmonized as FprEN ISO 80079-20-1
IEC 60079-32 series NOTE Harmonized as EN 60079-32 series
IEC 60664-1 NOTE Harmonized as EN 60664-1
IEC 60730 series NOTE Harmonized as EN 60730 series
IEC 61140 NOTE Harmonized as EN 61140
IEC 61439-1 NOTE Harmonized as EN 61439-1
ISO 4080 NOTE Harmonized as EN ISO 4080
ISO 15156-1 NOTE Harmonized as EN ISO 15156-1
IEC 62282-6-100 NOTE Harmonized as EN 62282-6-100
To be published.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60034 series Rotating electrical machines - -
IEC 60068-2-75 - Environmental testing - Part 2-75: Tests - EN 60068-2-75 -
Test Eh: Hammer tests
IEC 60079-2 - Explosive atmospheres - Part 2: EN 60079-2 -
Equipment protection by pressurized
enclosure "p"
IEC 60079-10 series Explosive atmospheres - Part 10-1: EN 60079-10 series
Classification of areas - Explosive gas
atmospheres
IEC 60079-15 - Explosive atmospheres - Part 15: EN IEC 60079-15 -
Equipment protection by type of protection
"n"
IEC 60079-29 series Explosive atmospheres - Part 29-1: Gas EN 60079-29 series
detectors - Performance requirements of
detectors for flammable gases
IEC 60086-4 - Primary batteries - Part 4: Safety of lithium EN 60086-4 -
batteries
IEC 60204-1 (mod) 2016 Safety of machinery - Electrical equipment EN 60204-1 2018
of machines - Part 1: General requirements
IEC 60216-4-1 - Electrical insulating materials - Thermal EN 60216-4-1 -
endurance properties -- Part 4-1: Ageing
ovens - Single-chamber ovens
IEC 60335-1 (mod) 2010 Household and similar electrical appliances EN 60335-1 2012
- Safety - Part 1: General requirements
+ A1 2013
+ A2 2016
- - + A11 2014
- - + AC 2014
- - + A13 2017
IEC 60364-4-41 - Low-voltage electrical installations - Part 4-HD 60364-4-41 -
41: Protection for safety - Protection
against electric shock
IEC 60529 - Degrees of protection provided by - -
enclosures (IP Code)
IEC 60695-2-11 - Fire hazard testing - Part 2-11: EN 60695-2-11 -
Glowing/hot-wire based test methods -
Glow-wire flammability test method for
end-products (GWEPT)
IEC 60695-2-13 - Fire hazard testing -- Part 2-13: EN 60695-2-13 -
Glowing/hot-wire based test methods -
Glow-wire ignition temperature (GWIT) test
method for materials
IEC 60695-11-5 - Fire hazard testing - Part 11-5: Test flames EN 60695-11-5 -
- Needle-flame test method - Apparatus,
confirmatory test arrangement and
guidance
IEC 60695-11-10 - Fire hazard testing -- Part 11-10: Test EN 60695-11-10 -
flames - 50 W horizontal and vertical flame
test methods
IEC 60695-11-20 - Fire hazard testing - Part 11-20: Test EN 60695-11-20 -
flames - 500 W flame test method
IEC 60730-1 (mod) 2013 Automatic electrical controls - Part 1: EN 60730-1 2016
General requirements
+ A1 2015 + A1 2016
IEC 60730-2-5 - Automatic electrical controls -- Part 2-5: EN 60730-2-5 -
Particular requirements for automatic
electrical burner control systems
IEC 60730-2-17 - Automatic electrical controls for household - -
and similar use -- Part 2-17: Particular
requirements for electrically operated gas
valves, including mechanical requirements
IEC 60812 - Analysis techniques for system reliability - EN 60812 -
Procedure for failure mode and effects
analysis (FMEA)
IEC 60884-1 - Plugs and socket-outlets for household and - -
similar purposes -- Part 1: General
requirements
IEC 60934 - Circuit-breakers for equipment (CBE) EN 60934 -
IEC 60950-1 (mod) 2005 Information technology equipment - Safety EN 60950-1 2006
- Part 1: General requirements
- - + A11 2009
+ A1 (mod) 2009 + A1 2010
- - + A12 2011
- - + AC 2011
+ A2 (mod) 2013 + A2 2013
IEC 60990 2016 Methods of measurement of touch current EN 60990 2016
and protective conductor current
IEC 61000-3-2 - Electromagnetic compatibility (EMC) - PartEN IEC 61000-3-2 -
3-2: Limits - Limits for harmonic current
emissions (equipment input current ≤ 16 A
per phase)
IEC 61000-3-3 - Electromagnetic compatibility (EMC) - PartE N 61000-3-3 -
3-3: Limits - Limitation of voltage changes,
voltage fluctuations and flicker in public
low-voltage supply systems, for equipment
with rated current ¿ 16 A per phase and
not subject to conditional connection
IEC 61000-6-1 - Electromagnetic compatibility (EMC) - PartE N 61000-6-1 -
6-1: Generic standards - Immunity
standard for residential, commercial and
light-industrial environments
IEC 61000-6-2 - Electromagnetic compatibility (EMC) - PartE N 61000-6-2 -
6-2: Generic standards - Immunity
standard for industrial environments
IEC 61000-6-3 - Electromagnetic compatibility (EMC) -- PartE N 61000-6-3 -
6-3: Generic standards - Emission
standard for residential, commercial and
light-industrial environments
IEC 61000-6-4 - Electromagnetic compatibility (EMC) - PartEN IEC 61000-6-4 -
6-4: Generic standards - Emission
standard for industrial environments
IEC 61025 - Fault Tree Analysis (FTA) EN 61025 -
IEC 61032 - Protection of persons and equipment by EN 61032 -
enclosures - Probes for verification
IEC 61508-1 - Functional safety of EN 61508-1 -
electrical/electronic/programmable
electronic safety-related systems - Part 1:
General requirements
IEC 61511-1 - Functional safety - Safety instrumented EN 61511-1 -
systems for the process industry sector -
Part 1: Framework, definitions, system,
hardware and application programming
requirements
IEC 61511-3 - Functional safety - Safety instrumented EN 61511-3 -
systems for the process industry sector -
Part 3: Guidance for the determination of
the required safety integrity levels
IEC 61882 - Hazard and operability studies (HAZOP EN 61882 -
studies) - Application guide
IEC 62040-1 - Uninterruptible power systems (UPS) - Part- -
1: Safety requirements
IEC 62040-2 - Uninterruptible power systems (UPS) - Part- -
2: Electromagnetic compatibility (EMC)
requirements
IEC 62133 series Secondary cells and batteries containing EN 62133 series
alkaline or other non-acid electrolytes -
Safety requirements for portable sealed
secondary cells, and for batteries made
from them, for use in portable applications
IEC 62282-2 - Fuel cell technologies -- Part 2: Fuel cell EN 62282-2 -
modules
ISO 3864 series Graphical symbols - Safety colours and - -
safety signs
ISO 7000 - Graphical symbols for use on equipment - - -
Registered symbols
ISO 7010 - Graphical symbols - Safety colours and EN ISO 7010 -
safety signs - Registered safety signs
ISO 15649 - Petroleum and natural gas industries - - -
Piping
ISO 16000-3 - Indoor air – Part 3: Determination of - -
formaldehyde and other carbonyl
compounds in indoor air and test chamber
air - Active sampling method
ISO 16000-6 - Indoor air – Part 6: Determination of - -
volatile organic compounds in indoor and
test chamber air by active sampling on
Tenax TA® sorbent, thermal desorption
and gas chromatography using MS or MS-
FID
ISO 16017-1 2000 Indoor, ambiant and workplace air - EN ISO 16017-1 2000
Sampling and analysis of volatile organic
compounds by sorbent tube/thermal
desorption/capillary gas chromatography –
Part 1: Pumped sampling
ISO 16111 - Transportable gas storage devices -- - -
Hydrogen absorbed in reversible metal
hydride
ISO 16528 series Boilers and pressure vessels - -
IEC 62282-5-100 ®
Edition 1.0 2018-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fuel cell technologies –
Part 5-100: Portable fuel cell power systems – Safety
Technologies des piles à combustible –
Partie 5-100: Systèmes à piles à combustible portables – Sécurité
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 27.070 ISBN 978-2-8322-5450-9
– 2 – IEC 62282-5-100:2018 © IEC 2018
CONTENTS
FOREWORD . 6
1 Scope . 8
2 Normative references . 10
3 Terms and definitions . 13
4 Design and construction requirements . 18
4.1 Physical environment and operating conditions . 18
4.1.1 General requirements . 18
4.1.2 Electrical power input . 18
4.1.3 Handling, transportation,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.