EN 62282-5-1:2012

Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety

IEC 62282-5-1:2012(E) covers construction, marking and test requirements for portable fuel cell power systems intended to produce electrical power. Applies to a.c. and d.c. type portable fuel cell power systems, with a rated output voltage not exceeding 600 V a.c., or 850 V d.c. for indoor and outdoor use. The major technical changes with respect to the first edition are as follows: - referencing an alternative test method; reduction of the limit on flammable atmospheres; - consideration of additional effluents and criteria to establish if a system is suitable for indoor or outdoor operation; - revision of specific criteria for oxygen detector sensor performance; - new test method and new drop heights; addition of a table giving limits on emission of effluents. Keywords: fuel cell

Brennstoffzellentechnologien - Teil 5-1: Portable Brennstoffzellen-Energiesysteme - Sicherheit

Technologies des piles à combustible - Partie 5-1: Systèmes à piles à combustible portables - Sécurité

Tehnologija gorivnih celic - 5-1. del: Naprave s prenosnimi gorivnimi celicami - Varnost

Ta del standarda IEC 62282 zajema zahteve za gradnjo, označevanje in preskušanje naprav s prenosnimi gorivnimi celicami. Te naprave z gorivnimi celicami so premične in niso pritrjene ali drugače nameščene na določeni lokaciji. Naprave s prenosnimi gorivnimi celicami so namenjene proizvodnji električne energije. Ta standard se uporablja za notranje ali zunanje naprave s prenosnimi gorivnimi celicami z izmenično ali enosmerno napetostjo, katerih nazivna izhodna efektivna napetost je manjša od 600 V izmenično ali 850 V enosmerno. Te naprave s prenosnimi gorivnimi celicami se ne smejo uporabljati na nevarnih lokacijah iz standarda IEV 426-03-01, razen če se sprejmejo dodatni zaščitni ukrepi v skladu s standardom IEC 60079-0. Ta standard se ne uporablja za naprave s prenosnimi gorivnimi celicami, a) ki so trajno priključene na sistem za distribucijo električne energije, b) ki so trajno priključene na sistem za distribucijo goriva, c) ki izvažajo električno energijo v omrežje, d) za pogon cestnih vozil, e) za uporabo na potniških letalih. Gorivne celice, ki omogočajo polnjenje akumulatorja hibridnih vozil, pri katerih akumulator zagotavlja električno energijo za pogon vozila, ne spadajo na področje uporabe tega standarda. Na področje uporabe tega standarda spadajo naslednja goriva in energenti: – zemeljski plin; – utekočinjeni naftni plini, kot sta propan in butan; – tekoči alkoholi, npr. metanol, etanol; – bencin; – dizelsko gorivo – kerozin; – vodik; – kovine (npr. Mg, Al ali Zn) ali kovinske zlitine, potopljene v elektrolit (npr. vodne raztopine soli ali alkalij) v zraku ali kisiku; – kemični hidridi. Ta standard ne izključuje uporabe podobnih goriv ali oksidantov iz drugih virov razen zraka, če se posebne nevarnosti obravnavajo v dodatnih zahtevah.

General Information

• Status: Withdrawn
• Publication Date: 22-Nov-2012
• Withdrawal Date: 22-Oct-2015
• ICS: 27.070 - Fuel cells
• Technical Committee: CLC/SR 105 - Fuel cell technologies
• Drafting Committee: IEC/TC 105 - IEC_TC_105
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 17-May-2021
• Completion Date: 17-May-2021
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: SIST EN 62282-5-1:2013 - Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety

Relations

• Replaces: EN 62282-5-1:2007 - Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
• Effective Date: 29-Jan-2023
• Replaced By: EN IEC 62282-5-100:2018 - Fuel cell technologies - Part 5-100: Portable fuel cell power systems - Safety
• Effective Date: 01-May-2018

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2013
Tehnologija gorivnih celic - 5-1. del: Naprave s prenosnimi gorivnimi celicami -
Varnost
Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
Brennstoffzellentechnologien - Teil 5-1: Portable Brennstoffzellen-Energiesysteme -
Sicherheit
Technologies des piles à combustible - Partie 5-1: Systèmes à piles à combustible
portables - Sécurité
Ta slovenski standard je istoveten z: EN 62282-5-1:2012
ICS:
27.070 Gorilne celice Fuel cells
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 62282-5-1
NORME EUROPÉENNE
November 2012
EUROPÄISCHE NORM
ICS 27.070 Supersedes EN 62282-5-1:2007

English version
Fuel cell technologies -
Part 5-1: Portable fuel cell power systems -
Safety
(IEC 62282-5-1:2012)
Technologies des piles à combustible -  Brennstoffzellentechnologien -
Partie 5-1: Systèmes à piles à Teil 5-1: Portable Brennstoffzellen-
combustible portables - Energiesysteme -
Sécurité Sicherheit
(CEI 62282-5-1:2012) (IEC 62282-5-1:2012)

This European Standard was approved by CENELEC on 2012-10-23. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62282-5-1:2012 E
Foreword
The text of document 105/396/FDIS, future edition 2 of IEC 62282-5-1, prepared by IEC/TC 105 "Fuel cell
technologies" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2013-07-23
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-10-23

standards conflicting with the
document have to be withdrawn
This document supersedes EN 62282-5-1:2007.
1:2007:
 normative references and definitions have been updated (e.g., hazardous locations, micro fuel cell
power systems, transportable equipment, etc.);
 subclause 4.2.2 has been updated referencing an alternative test method in response to a comment;
 the limit on flammable atmospheres has been reduced from 50 % of LFL to 25 % of LFL in 4.5.4 and in
7.20;
 subclause 4.14 and the corresponding tests in 7.22 have been updated to include more effluents and
criteria to establish if a system is suitable for indoor or outdoor operation;
 specific criteria for oxygen detector sensor performance requirements have been revised in 7.21;
 subclause 7.18 has been updated with a new test method and new drop heights in response to
comments;
 Table 1 has been added giving limits on emission of effluents using limits drawn from the micro fuel cell
power system standard.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed
for Use within Certain Voltage Limits (LVD - 2006/95/EC).

- 3 - EN 62282-5-1:2012
Endorsement notice
The text of the International Standard IEC 62282-5-1:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60439-1 NOTE  Harmonized as EN 60439-1.
IEC 62282-6-100 NOTE  Harmonized as EN 62282-6-100.
ISO 15156-1 NOTE  Harmonized as EN ISO 15156-1.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60034 Series Rotating electrical machines EN 60034 Series

IEC 60068-2-75 - Environmental testing - EN 60068-2-75 -
Part 2-75: Tests - Test Eh: Hammer tests

IEC 60079-0 - Explosive atmospheres - EN 60079-0 -
Part 0: Equipment - General requirements

IEC 60079-2 - Explosive atmospheres - EN 60079-2 -
Part 2: Equipment protection by pressurized
enclosure "p"
IEC 60079-10 - Electrical apparatus for explosive gas EN 60079-10 -
atmospheres -
Part 10: Classification of hazardous areas

IEC 60079-15 - Explosive atmospheres - EN 60079-15 -
Part 15: Equipment protection by type of
protection "n"
IEC 60079-20-1 - Explosive atmospheres - EN 60079-20-1 -
Part 20-1: Material characteristics for gas and
vapour classification - Test methods and data

IEC 60079-29-1 - Explosive atmospheres - EN 60079-29-1 -
Part 29-1: Gas detectors - Performance
requirements of detectors for flammable
gases
IEC 60086-4 - Primary batteries - EN 60086-4 -
Part 4: Safety of lithium batteries

IEC 60204-1 (mod) 2005 Safety of machinery - Electrical equipment of EN 60204-1 2006
machines - + corr. February 2010
Part 1: General requirements
IEC 60216-4-1 - Electrical insulating materials - Thermal EN 60216-4-1 -
endurance properties -
Part 4-1: Ageing ovens - Single-chamber
ovens
IEC 60335-1 (mod) 2010 Household and similar electrical appliances - EN 60335-1 2012
+ corr. July 2010 Safety -
+ corr. April 2011 Part 1: General requirements

IEC 60364-4-41 - Low-voltage electrical installations - HD 60364-4-41 -
Part 4-41: Protection for safety - Protection
against electric shock
IEC 60529 - Degrees of protection provided by enclosures - -
(IP Code)
- 5 - EN 62282-5-1:2012
Publication Year Title EN/HD Year

IEC 60664-1 - Insulation coordination for equipment within EN 60664-1 -
low-voltage systems -
Part 1: Principles, requirements and tests

IEC 60695-2-11 - Fire hazard testing - EN 60695-2-11 -
Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test method
for end-products
IEC 60695-2-13 - Fire hazard testing - EN 60695-2-13 -
Part 2-13: Glowing/hot-wire based test
methods - Glow-wire ignition temperature
(GWIT) test method for materials

IEC 60695-11-5 - Fire hazard testing - EN 60695-11-5 -
Part 11-5: Test flames - Needle-flame test
method - Apparatus, confirmatory test
arrangement and guidance
IEC 60695-11-10 - Fire hazard testing - EN 60695-11-10 -
Part 11-10: Test flames - 50 W horizontal and
vertical flame test methods
IEC 60695-11-20 - Fire hazard testing - EN 60695-11-20 -
Part 11-20: Test flames - 500 W flame test
methods
IEC 60730-1 (mod) 2010 Automatic electrical controls for household EN 60730-1 2011
and similar use -
Part 1: General requirements
IEC 60730-2-5- - Automatic electrical controls for household EN 60730-2-5 -
and similar use -
Part 2-5: Particular requirements for automatic
electrical burner control systems

IEC 60730-2-17 - Automatic electrical controls for household - -
and similar use -
Part 2-17: Particular requirements for
electrically operated gas valves, including
mechanical requirements
IEC 60812 - Analysis techniques for system reliability - EN 60812 -
Procedure for failure mode and effects
analysis (FMEA)
IEC 60884-1 - Plugs and socket-outlets for household and - -
similar purposes -
Part 1: General requirements
IEC 60934 - Circuit-breakers for equipment (CBE) EN 60934 -

IEC 60950-1 (mod) 2005 Information technology equipment - Safety - EN 60950-1 2006
+ corr. August 2006 Part 1: General requirements + A11 2009
+ A12 2011
+ AC 2011
IEC 60990 1999 Methods of measurement of touch current EN 60990 1999
and protective conductor current

IEC 61000-3-2 - Electromagnetic compatibility (EMC) - EN 61000-3-2 -
Part 3-2: Limits - Limits for harmonic current
emissions (equipment input current ≤ 16 A per
phase)
Publication Year Title EN/HD Year

IEC 61000-3-3 - Electromagnetic compatibility (EMC) - EN 61000-3-3 -
Part 3-3: Limits - Limitation of voltage
changes, voltage fluctuations and flicker in
public low-voltage supply systems, for
equipment with rated current ≤ 16 A per phase
and not subject to conditional connection

IEC 61000-6-1 - Electromagnetic compatibility (EMC) - EN 61000-6-1 -
Part 6-1: Generic standards - Immunity for
residential, commercial and light-industrial
environments
IEC 61000-6-2 - Electromagnetic compatibility (EMC) - EN 61000-6-2 -
Part 6-2: Generic standards - Immunity for
industrial environments
IEC 61000-6-3 - Electromagnetic compatibility (EMC) - EN 61000-6-3 -
Part 6-3: Generic standards - Emission
standard for residential, commercial and light-
industrial environments
IEC 61000-6-4 - Electromagnetic compatibility (EMC) - EN 61000-6-4 -
Part 6-4: Generic standards - Emission
standard for industrial environments

IEC 61025 - Fault Tree Analysis (FTA) EN 61025 -

IEC 61032 - Protection of persons and equipment by EN 61032 -
enclosures - Probes for verification

IEC 61140 - Protection against electric shock - Common EN 61140 -
aspects for installation and equipment

IEC 61439-1 - Low-voltage switchgear and controlgear EN 61439-1 -
assemblies -
Part 1: General rules
IEC 61508-1 - Functional safety of EN 61508-1 -
electrical/electronic/programmable electronic
safety-related systems -
Part 1: General requirements
IEC 61511-1 - Functional safety - Safety instrumented EN 61511-1 -
systems for the process industry sector -
Part 1: Framework, definitions, system,
hardware and software requirements

IEC 61511-3 - Functional safety - Safety instrumented EN 61511-3 -
systems for the process industry sector -
Part 3: Guidance for the determination of the
required safety integrity levels

IEC 61882 - Hazard and operability studies (HAZOP - -
studies) - Application guide
IEC 62040-1 - Uninterruptible Power Systems (UPS) - EN 62040-1 -
Part 1: General and safety requirements for
UPS
IEC 62040-2 - Uninterruptible power systems (UPS) - EN 62040-2 -
Part 2: Electromagnetic compatibility (EMC)
requirements
IEC 62133 - Secondary cells and batteries containing EN 62133 -
alkaline or other non-acid electrolytes - Safety
requirements for portable sealed secondary
cells, and for batteries made from them, for
use in portable applications
- 7 - EN 62282-5-1:2012
Publication Year Title EN/HD Year

IEC 62282-2 - Fuel cell technologies - EN 62282-2 -
Part 2: Fuel cell modules
ISO 3864 Series Graphical symbols - Safety colours and safety - -
signs
ISO 4080 - Rubber and plastics hoses and hose EN ISO 4080 -
assemblies - Determination of permeability to
gas
ISO 7000 - Graphical symbols for use on equipment - - -
Index and synopsis
ISO 7010 - Graphical symbols - Safety colours and safety EN ISO 7010 -
signs - Registered safety signs

ISO 15649 - Petroleum and natural gas industries - Piping - -

ISO 16000-3 - Indoor air - - -
Part 3: Determination of formaldehyde and
other carbonyl compounds - Active sampling
method
ISO 16000-6 - Indoor air - - -
Part 6: Determination of volatile organic
compounds in indoor and test chamber air by
active sampling on Tenax TA sorbent, thermal
desorption and gas chromatography using
MS/FID
ISO 16017-1 2000 Indoor, ambient and workplace air - Sampling EN ISO 16017-1 2000
and analysis of volatile organic compounds by
sorbent tube/thermal desorption/capillary gas
chromatography -
Part 1: Pumped sampling
ISO 16110-1 2007 Hydrogen generators using fuel processing - -
technologies -
Part 1: Safety
ISO 16111 - Transportable gas storage devices - Hydrogen - -
absorbed in reversible metal hydride

ISO 16528 - Boilers and pressure vessels - Registration of - -
Codes and Standards to promote international
recognition
IEC 62282-5-1 ®
Edition 2.0 2012-09
INTERNATIONAL
STANDARD
Fuel cell technologies –
Part 5-1: Portable fuel cell power systems – Safety

INTER
...