EN 60684-3-165:2004

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 165: Extruded polyolefin, flame retarded, limited fire hazard sleeving

Gives the requirements for two types of extruded polyolefin, flame retarded, limited fire hazard sleeving. Type A: Thin wall - Internal diameter up to 30 mm Type B: Thick wall - Internal diameter up to 30 mm These sleevings are normally supplied in the following colours: black, red, green, blue, white and yellow. These sleevings are for use up to temperatures of 90 °C. Sizes or colours other than those listed in this standard may be available as custom items. These items are considered to comply with this standard if they comply with the requirements listed in Tables 2, 3, and 4, excluding dimensions. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 165: Extrudierte Polyolefinschläuche, flammwidrig, mit verbessertem Verhalten im Brandfall

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 165: Gaines en polyoléfine extrudées, retardées à la flamme, à résistance au feu limitée

Donne les exigences relatives à deux types de gaines en polyoléfine extrudées, retardées à la flamme, à résistance au feu limitée. Type A: Paroi mince - Diamètre intérieur allant jusqu'à 30 mm Type B: Paroi épaisse - Diamètre intérieur allant jusqu'à 30 mm Ces gaines sont normalement fournies dans les couleurs suivantes: noir, rouge, vert, bleu, blanc et jaune. Ces gaines sont adaptées pour un usage allant jusqu'à des températures de 90 °C. D'autres dimensions et d'autres couleurs que celles indiquées dans cette norme peuvent être disponibles, comme articles spéciaux. Ces articles sont considérés comme satisfaisant à cette norme s'ils correspondent aux exigences indiquées dans les Tableaux 2, 3 et 4, en excluant les dimensions. Les matériaux conformes à la présente spécification satisfont à des niveaux de performances établis. Cependant, il convient que le choix d'un matériau, par un utilisateur, pour une application spécifique, soit fondé sur les exigences réelles nécessaires pour obtenir les performances satisfaisantes pour cette application et qu'il ne soit pas fondé sur cette seule spécification.

Gibke izolacijske cevi – 3. del: Specifikacija za posamezne vrste cevi – 165. list: Cevi iz ekstrudiranega poliolefina, ognjevarne, z izboljšanimi protipožarnimi lastnostmi (IEC 60684-3-165:2004)

General Information

• Status: Published
• Publication Date: 08-Jul-2004
• Withdrawal Date: 30-Jun-2007
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: CLC/SR 15 - Insulating materials
• Drafting Committee: IEC/TC 15 - IEC_TC_15
• Parallel Committee: IEC/SC 15C - IEC_SC_15C
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 09-Jul-2004
• Completion Date: 09-Jul-2004
• Ref Project: SIST EN 60684-3-165:2005 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 165: Extruded polyolefin, flame retarded, limited fire hazard sleeving

Standards Content (Sample)

STANDARD(istoveten EN 60684-3-165:2004)Gibke izolacijske cevi – 3. del: Specifikacija za posamezne vrste cevi – 165. list: Cevi iz ekstrudiranega poliolefina, ognjevarne, z izboljšanimi protipožarnimi lastnostmi (IEC 60684-3-165:2004)Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 165: Extruded polyolefin, flame retarded, limited fire hazard sleeving (IEC 60684-3-165:2004)©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 60684-3-165:2005(en)ICS29.035.20

EUROPEAN STANDARD
EN 60684-3-165 NORME EUROPÉENNE EUROPÄISCHE NORM
July 2004 CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-165:2004 E
ICS 29.035.20
English version
Flexible insulating sleeving Part 3: Specifications for individual types of sleeving Sheet 165: Extruded polyolefin, flame retarded,
limited fire hazard sleeving (IEC 60684-3-165:2004)
Gaines isolantes souples Partie 3: Spécifications pour types particuliers de gaines Feuille 165: Gaines en polyoléfine extrudées, retardées à la flamme,
à résistance au feu limitée (CEI 60684-3-165:2004)
Isolierschläuche Teil 3: Anforderungen für einzelne Schlauchtypen Blatt 165: Extrudierte Polyolefinschläuche, flammwidrig, mit verbessertem Verhalten im Brandfall (IEC 60684-3-165:2004)
This European Standard was approved by CENELEC on 2004-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Foreword The text of document 15C/1598/FDIS, future edition 1 of IEC 60684-3-165, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60684-3-165 on 2004-07-01. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2005-04-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2007-07-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 60684-3-165:2004 was approved by CENELEC as a European Standard without any modification. __________

- 3 - EN 60684-3-165:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60684-1 2003 Flexible insulating sleeving Part 1: Definitions and general requirements
EN 60684-1 2003 IEC 60684-2 1997 Part 2: Methods of test
EN 60684-2 1997 IEC 60757 1983 Code for designation of colours
HD 457 S1 1985 ISO 1817 1999 Rubber, vulcanized - Determination of the effect of liquids
- -
NORME INTERNATIONALECEIIEC INTERNATIONAL STANDARD 60684-3-165Première éditionFirst edition2004-05 Gaines isolantes souples – Partie 3: Spécifications pour types particuliers de gaines – Feuille 165: Gaines en polyoléfine extrudées, retardées à la flamme, à résistance au feu limitée
Flexible insulating sleeving – Part 3: Specifications for individual types of sleeving – Sheet 165: Extruded polyolefin, flame retarded, limited fire hazard sleeving
Pour prix, voir catalogue en vigueur For price, see current catalogue IEC 2004
Droits de reproduction réservés

Copyright - all rights reserved Aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: [phone] Telefax: [phone] E-mail: [e-mail]
Web: www.iec.ch CODE PRIX PRICE CODE J Commission Electrotechnique InternationaleInternational Electrotechnical Commission

60684-3-165  IEC:2004 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ___________
FLEXIBLE INSULATING SLEEVING –
Part 3: Specifications for individual types of sleeving – Sheet 165: Extruded polyolefin, flame retarded,
limited fire hazard sleeving
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other da
...