EN IEC 61643-01:2025/A11:2025
(Amendment)Low-voltage surge protective devices - Part 01: General Requirements and test methods
Low-voltage surge protective devices - Part 01: General Requirements and test methods
Überspannungsschutzgeräte für Niederspannung - Teil 1: Allgemeine Anforderungen und Prüfverfahren
Parafoudres basse tension - Partie 01: Exigences générales et méthodes d’essai
Nizkonapetostne naprave za zaščito pred prenapetostnimi udari - 1. del: Splošne zahteve in preskusne metode - Dopolnilo A11
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2025
Nizkonapetostne naprave za zaščito pred prenapetostnimi udari - 1. del: Splošne
zahteve in preskusne metode - Dopolnilo A11
Low-voltage surge protective devices - Part 01: General Requirements and test methods
Überspannungsschutzgeräte für Niederspannung - Teil 1: Allgemeine Anforderungen
und Prüfverfahren
Parafoudres basse tension - Partie 01: Exigences générales et méthodes d’essai
Ta slovenski standard je istoveten z: EN IEC 61643-01:2025/A11:2025
ICS:
29.120.50 Varovalke in druga Fuses and other overcurrent
nadtokovna zaščita protection devices
29.240.10 Transformatorske postaje. Substations. Surge arresters
Prenapetostni odvodniki
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61643-01:2025/A11
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2025
ICS 29.240.10
English Version
Low-voltage surge protective devices - Part 01: General
Requirements and test methods
Parafoudres basse tension - Partie 01: Exigences Überspannungsschutzgeräte für Niederspannung - Teil 1:
générales et méthodes d'essai Allgemeine Anforderungen und Prüfverfahren
This amendment A11 modifies the European Standard EN IEC 61643-01:2025; it was approved by CENELEC on 2024-10-28. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61643-01:2025/A11:2025 E
Contents Page
European foreword . 3
1 Modification to Clause 2, “Normative references” . 4
2 Addition of subclause 8.8, “Additional information if declared by the manufacturer -
Vibration and shock” . 4
3 Modification to Table 16, “Cross-sections of copper conductors for screw-type or
screwless terminals” . 4
4 Modification to A.1, “Routine tests” . 4
5 Modification to G.2.2, “Preconditioning procedure” . 4
6 Addition of Annex ZB, “Vibration and shock test” . 4
Annex ZA (normative) Normative references to international publications with their corresponding
European publications . 7
Annex ZZ (informative) Relationship between this European standard and the safety objectives of
Directive 2014/35/EU [2014 OJ L96] aimed to be covered . 9
European foreword
This document (EN IEC 61643-01:2025/A11:2025) has been prepared by Technical Committee CLC/TC 37A
“Low voltage surge protective devices”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2026-04-30
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2028-04-30
conflicting with this document have to be
withdrawn
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 61643-01 ED1
are prefixed “Z”.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CENELEC by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZZ, which is an integral part of this document.
Any feedback and questions on this document should be directed to the users’ national committee. A complete
listing of these bodies can be found on the CENELEC website.
1 Modification to Clause 2, “Normative references”
Add the following references:
IEC 60364-5-53:2019, Low-voltage electrical installations -- Part 5-53: Selection and erection of electrical
equipment - Protection, isolation, switching, control and monitoring
ISO 4892-1:2016, Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance
ISO 4892-2:2013, Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps -
Amendment 1: Classification of daylight filters
ISO 4628-3:2016, Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and
size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting
2 Addition of subclause 8.8, “Additional information if declared by the
manufacturer - Vibration and shock”
Add the following new subclause 8.8 after 8.7:
“8.7 Additional information if declared by the manufacturer - Vibration and shock
Information on vibration and shock tests for transportation and special applications can be found in Annex ZB.”
3 Modification to Table 16, “Cross-sections of copper conductors for screw-type or
screwless terminals”
Delete the column “American Wire Gauge”.
4 Modification to A.1, “Routine tests”
Replace the whole paragraph with the following:
“Appropriate test(s) shall be performed during manufacturing production to verify that the SPD is capable of
meeting its performance.”
5 Modification to G.2.2, “Preconditioning procedure”
Replace the Note with the following:
“
NOTE After the preconditioning, the modification of the samples is done by the manufacturer under supervision of the
test laboratory to avoid any unintended damage to the test samples.”
6 Addition of Annex ZB, “Vibration and shock test”
Add the following annex:
“
As impacted by IEC 60364-5-53:2019/AMD1:2020.
As impacted by ISO 4892-2:2013/AMD1:2021.
Annex ZB
(informative)
Vibration and shock test
ZB.1 Introduction
This annex gives information if the manufacturer declares performances for vibration and shock conditions.
ZB.2 Vibration and shock test
Vibration and shock tests shall be performed according to
— EN 60068-2-6 for sinusoidal Vibration test,
— EN 60068-2-64 for broadband random Vibration test, and
— EN 60068-2-27 for shock test.
Usually SPD are subject to mechanical stress due to transportation. This should be checked by a vibration and
shock test with the parameters given in EN 60721-3-2.
Special application of SPDs may require additional vibration and shock tests.
The typical values can be as shown in Table ZB.1.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.