EN 62561-3:2012
(Main)Lightning Protection System Components (LPSC) - Part 3: Requirements for isolating spark gaps
Lightning Protection System Components (LPSC) - Part 3: Requirements for isolating spark gaps
IEC 62561-3:2012(E) specifies the requirements and tests for isolating spark gaps (ISG) for lightning protection systems. ISGs can be used to indirectly bond a lightning protection system to other nearby metalwork where a direct bond is not permissible for functional reasons.
Blitzschutzsystembauteile (LPSC) - Teil 3: Anforderungen an Trennfunkenstrecken
Composants de système de protection contre la foudre (CSPF) - Partie 3: Exigences pour les éclateurs d'isolement
L'IEC 62561-3:2012 spécifie les exigences et les essais à appliquer aux éclateurs d'isolement liés à un système de protection contre la foudre. Les éclateurs d'isolement peuvent être utilisés pour raccorder indirectement un système de protection contre la foudre à une partie métallique proche, lorsqu'un raccordement direct n'est pas admissible pour des raisons fonctionnelles.
Elementi za zaščito pred strelo (LPSC) - 3. del: Zahteve za izolacijska iskrišča (IEC 62561-3:2012, spremenjen)
Ta del standarda IEC 62561 določa zahteve in preskuse za izolacijska iskrišča (ISG) sistemov za zaščito pred strelo. Izolacijska iskrišča se lahko uporabljajo za posredno povezovanje sistema za zaščito pred strelo na druge bližnje kovinske konstrukcije, kjer neposredna povezava ni dovoljena zaradi funkcionalnih razlogov. Običajna uporaba vključuje povezavo z naslednjimi sistemi: – ozemljitveni sistemi električnih inštalacij; – ozemljitveni sistemi telekomunikacijskih sistemov; – pomožna ozemljila zemeljskostičnih odklopnikov pod napetostjo; – železniško ozemljilo izmeničnih in enosmernih železnic; – merilna ozemljila za laboratorije; – namestitev s sistemi katodne zaščite in blodečih tokov; – servisni vhodni stebri za nizkonapetostne nadzemne kable; – obvodne izolirane prirobnice in izolirani spojniki cevovodov. Ta standard ne obravnava področij uporabe, kjer nastajajo sledilni tokovi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2012
1DGRPHãþD
SIST EN 50164-3:2006
SIST EN 50164-3:2006/A1:2009
(OHPHQWL]D]DãþLWRSUHGVWUHOR /36& GHO =DKWHYH]DL]RODFLMVNDLVNULãþD ,(&
VSUHPHQMHQ
Lightning Protection System Components (LPSC) - Part 3: Requirements for isolating
spark gaps
Blitzschutzsystembauteile (LPSC) - Teil 3: Anforderungen an Trennfunkenstrecken
Composants de systèmes de protection contre la foudre (CSPF) - Partie 3: Exigences
pour les éclateurs d'isolement
Ta slovenski standard je istoveten z: EN 62561-3:2012
ICS:
91.120.40 =DãþLWDSUHGVWUHOR Lightning protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 62561-3
NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM
ICS 29.020; 91.120.40 Supersedes EN 50164-3:2006 + A1:2009
English version
Lightning Protection System Components (LPSC) -
Part 3: Requirements for isolating spark gaps
(IEC 62561-3:2012, modified)
Composants de système de protection Blitzschutzsystembauteile (LPSC) -
contre la foudre (CSPF) - Teil 3: Anforderungen an
Partie 3: Exigences pour les éclateurs Trennfunkenstrecken
d'isolement (CEI 62561-3:2012, modifiée) (IEC 62561-3:2012, modifiziert)
This European Standard was approved by CENELEC on 2012-03-16. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
-
Ref. No. EN 62561-3:2012 E
Foreword
The text of document 81/418/FDIS, future edition 1 of IEC 62561-3, prepared by IEC/TC 81, "Lightning
protection", was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
A draft amendment, which covers common modifications to IEC 62561-3 (81/418/FDIS), was prepared
by CLC/TC 81X "Lightning protection" and approved by CENELEC.
The following dates are fixed:
– latest date by which this document has to be (dop) 2013-03-16
implemented at national level
by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2015-03-16
with this document have to be withdrawn
This document supersedes EN 50164-3:2006 + A1:2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62561-3:2012 are prefixed “Z”.
Endorsement notice
The text of the International Standard IEC 62561-3:2012 was approved by CENELEC as a European
Standard with agreed common modifications.
- 3 - EN 62561-3:2012
COMMON MODIFICATIONS
Whole document
Replace all references to IEC 62305 by references to EN 62305.
Replace all references to IEC 62561 by references to EN 62561.
1 Scope
Add the following at the end of the clause:
Protective devices according to EN 50122-1 and EN 50123-5 are outside the scope of this European
Standard.
6 Tests
a
Under 6.2.4.1, Table 1, footnote , replace "IEC 62305-1 and IEC 61643-11" by "EN 62305-1 and
EN 61643-11".
Annexes
Annex A (normative) Environmental test for isolating spark gaps
In A.2, replace thrice "IEC 60068-2-52:1996" by "EN 60068-2-52:1996".
Add the following new annexes:
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60068-2-52 1996 Environmental testing - EN 60068-2-52 1996
+ corr. July 1996 Part 2: Tests - Test Kb: Salt mist, cyclic (sodium
chloride solution)
IEC 61643-11 - Low-voltage surge protective devices - EN 61643-11 -
Part 11: Surge protective devices connected to low-
voltage power systems - Requirements and test
methods
IEC 62305-1 - Protection against lightning - EN 62305-1 -
Part 1: General principles
IEC 62561-1 - Lightning Protection System Components (LPSC) - EN 62561-1 -
Part 1: Requirements for connection components
ISO 6957 1988 Copper alloys - Ammonia test for stress corrosion - -
resistance
ISO 6988 1985 Metallic and other non-organic coatings - Sulfur EN ISO 6988 1994
dioxide test with general condensation of moisture
- 5 - EN 62561-3:2012
Annex ZB
(informative)
Identification and differences of tests between
Table ZB.1 – Identification and differences of tests
between EN 62561-3:2012 and EN 50164-3:2006 + A1:2009
EN 50164-3:2006 +
Test description EN 62561-3:2012 Deviations / Remarks
A1:2009
Isolation resistance 6.2.1 6.2.1 None
Withstand voltage 6.2.2 6.2.2 None
Rated impulse sparkover
6.2.3 6.2.3 None
voltage
Lightning current 6.2.4 6.2.4 None
Isolation resistance 6.2.5 6.2.4.1 None
Withstand voltage 6.2.6 6.2.4.2 None
Rated impulse sparkover
6.2.7 6.2.4.3 None
voltage
Marking test 6.3 6.3 None
Bibliography
Add the following reference:
EN 50164-3:2006 + A1:2009, Lightning Protection Components (LPC) – Part 3: Requirements for
isolating spark gaps
Replace the references to IEC standards with the following:
EN 60529, Degrees of protection provided by enclosures (IP Code) (IEC 60529)
EN 62305-3, Protection against lightning – Part 3: Physical damage to structures and life hazard
(IEC 62305-3)
EN 62305-4, Protection against lightning – Part 4: Electrical and electronic systems within structures
(IEC 62305-4)
IEC 62561-3 ®
Edition 1.0 2012-02
INTERNATIONAL
STANDARD
Lightning protection system components (LPSC) –
Part 3: Requirements for isolating spark gaps (ISG)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
R
ICS 29.020; 91.120.40 ISBN 978-2-88912-923-2
– 2 – 62561-3 © IEC:2012(E)
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Classification . 9
5 Requirements . 9
5.1 General . 9
5.2 Environmental requirements . 9
5.3 Installation instructions . 9
5.4 Lightning current carrying capability . 10
5.5 Rated impulse sparkover voltage . 10
5.6 Rated withstand voltage . 10
5.6.1 Rated DC withstand voltage . 10
5.6.2 Rated AC withstand voltage . 10
5.7 Isolation resistance . 10
5.8 Marking . 10
5.9 UV resistance . 10
6 Tests . 11
6.1 General conditions for tests . 11
6.2 Electrical test . 11
6.2.1 Isolation resistance. 11
6.2.2 Withstand voltage . 11
6.2.3 Rated impulse sparkover voltage . 12
6.2.4 Lightning current . 12
6.2.5 Isolation resistance. 13
6.2.6 Withstand voltage . 13
6.2.7 Rated impulse sparkover voltage . 13
6.3 Marking test . 13
6.3.1 General conditions for tests . 13
6.3.2 Acceptance criteria . 13
7 Electromagnetic compatibility (EMC) . 14
8 Structure and content of the test report . 14
8.1 General . 14
8.2 Report identification . 14
8.3 Specimen description . 14
8.4 Standards and references . 14
8.5 Test procedure . 15
8.6 Testing equipment description . 15
8.7 Measuring instruments description . 15
8.8 Results and parameters recorded . 15
8.9 Statement of pass/fail . 15
Annex A (normative) Environmental test for isolating spark gaps . 16
Annex B (normative) Flow chart of tests . 17
62561-3 © IEC:2012(E) – 3 –
Bibliography . 18
a
Table 1 – Lightning impulse current (I ) parameters . 13
imp
– 4 – 62561-3 © IEC:2012(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) –
Part 3: Requirements for isolating spark gaps (ISG)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.