EN 61076-2-104:2014
(Main)Connectors for electronic equipment - Product requirements - Part 2-104: Circular connectors - Detail specification for circular connectors with M8 screw-locking or snap-locking
Connectors for electronic equipment - Product requirements - Part 2-104: Circular connectors - Detail specification for circular connectors with M8 screw-locking or snap-locking
IEC 61076-2-104:2014 describes circular connectors M8 screw-locking or with nominal diameter 8 mm snap-locking, typically used for industrial process measurement and control. These connectors consist of fixed and free connectors either rewireable or non-rewireable. Male connectors have round contacts of diameter 0,6 mm, diameter 0,7 mm and diameter 1,0 mm. This second edition cancels and replaces the first edition published in 2008. This edition constitutes a technical revision. The main technical changes with regard to the previous edition are as follows: - three new type ways have been added to the A-coding, including new gauges and contact diameters and - the type designation has been removed. Key words: Connectors, Circular Connectors, Data transmission
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 2-104: Rundsteckverbinder - Bauartspezifikation für Rundsteckverbinder M8 mit Schraub- oder Rastverriegelung
Connecteurs pour équipements électroniques - Exigences de produit - Partie 2-104: Connecteurs circulaires - Spécification particulière pour les connecteurs circulaires M8 à vis ou à encliquetage
L'IEC 61076-2-104:2014 décrit les connecteurs circulaires M8 à vis ou à encliquetage de 8 mm de diamètre nominal, généralement utilisés pour les mesures et les commandes dans les processus industriels. Ces connecteurs se composent d'embases et de fiches, démontables ou non. Les connecteurs mâles possèdent des contacts arrondis, de diamètre de 0,6 mm, de diamètre de 0,7 mm et de diamètre de 1,0 mm. Cette deuxième édition annule et remplace la première édition parue en 2008. Cette édition constitue une révision technique. Les principales modifications techniques par rapport à l'édition précédente sont: - trois nouveaux types de voies ont été ajoutés au codage-A, y compris de nouveaux calibres et diamètres de contact et - la désignation de type a été supprimée. Mots-clés: connecteurs, connecteurs circulaires, transmission de données
Konektorji za elektronsko opremo - Zahteve za izdelek - 2-104. del: Okrogli konektorji - Podrobna specifikacija za okrogle konektorje z vijačnim M8 ali zaskočnim zaklepanjem (IEC 61076-2-104:2014)
Ta del standarda IEC 61076 opisuje okrogle konektorje z vijačnim M8 zaklepanjem ali zaskočnim zaklepanjem z nominalnim premerom 8 mm, ki se običajno uporabljajo za merjenje in krmiljenje v industrijskih procesih. Ti konektorji so sestavljeni iz pritrjenih in prostih konektorjev z možnostjo ponovnega ožičenja ali brez. Moški konektorji imajo okrogle kontakte s premerom 0,6 mm, 0,7 mm in 1,0 mm.
V tej podrobni specifikaciji so mere navedene v milimetrih.
OPOMBA M8 je mera navoja mehanizma z vijačnim zaklepanjem teh okroglih konektorjev.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Steckverbinder für elektronische Einrichtungen - Produktanforderungen -- Teil 2-104: Rundsteckverbinder - Bauartspezifikation für Rundsteckverbinder M8 mit Schraub- oder RastverriegelungConnecteurs pour équipements électroniques - Exigences de produit -- Partie 2-104: Connecteurs circulaires - Spécification particulière pour les connecteurs circulaires M8 à vis ou à encliquetageConnectors for electronic equipment - Product requirements -- Part 2-104: Circular connectors - Detail specification for circular connectors with M8 screw-locking or snap-locking31.220.10Plug-and-socket devices. ConnectorsICS:Ta slovenski standard je istoveten z:EN 61076-2-104:2014SIST EN 61076-2-104:2014en01-december-2014SIST EN 61076-2-104:2014SLOVENSKI
STANDARDSIST EN 61076-2-104:20081DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 61076-2-104
October 2014 ICS 31.220.10
Supersedes EN 61076-2-104:2008
English Version
Connectors for electronic equipment - Product requirements - Part 2-104: Circular connectors - Detail specification for circular connectors with M8 screw-locking or snap-locking (IEC 61076-2-104:2014)
Connecteurs pour équipements électroniques - Exigences de produit - Partie 2-104: Connecteurs circulaires - Spécification particulière pour les connecteurs circulaires M8 à vis ou à encliquetage (CEI 61076-2-104:2014)
Steckverbinder für elektronische Einrichtungen - Produktanforderungen - Teil 2-104: Rundsteckverbinder - Bauartspezifikation für Rundsteckverbinder M8 mit Schraub- oder Rastverriegelung (IEC 61076-2-104:2014) This European Standard was approved by CENELEC on 2014-10-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61076-2-104:2014 E SIST EN 61076-2-104:2014
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-07-14 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-10-14
This document supersedes EN 61076-2-104:2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 61076-2-104:2014 was approved by CENELEC as a European Standard without any modification. SIST EN 61076-2-104:2014
- 3 - EN 61076-2-104:2014 Annex ZA (normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu
Publication Year Title EN/HD Year
IEC 60050 Series
International Electrotechnical Vocabulary - -
IEC 60068-1 2013
Environmental testing -
Part 1: General and guidance EN 60068-1 2014
IEC 60068-2-60 -
Environmental testing -
Part 2: Tests - Test Ke: Flowing mixed
gas corrosion test EN 60068-2-60 -
IEC 60352 Series
Solderless connections EN 60352 Series
IEC 60512 Series
Connectors for electronic equipment - Tests and measurements EN 60512 Series
IEC 60529
+ A1 + A2
1999 2013 Degrees of protection provided by enclosures (IP Code) EN 60529 corr. May + A1 + A2 1991
1993 2000 2013 IEC 60664-1 2007
Insulation coordination for equipment within low-voltage systems -
Part 1: Principles, requirements and tests EN 60664-1 2007
IEC 60998-2-1 -
Connecting devices for low-voltage
circuits for household
and similar purposes -
Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units EN 60998-2-1 -
IEC 60999 Series
Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units EN 60999 Series
IEC 61076-1 2006
Connectors for electronic equipment - Product requirements -
Part 1: Generic specification EN 61076-1 2006
IEC 61984 -
Connectors - Safety requirements and tests EN 61984 -
ISO 1302 -
Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation EN ISO 1302 -
IEC 61076-2-104 Edition 2.0 2014-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment – Product requirements –
Part 2-104: Circular connectors – Detail specification for circular connectors
with M8 screw-locking or snap-locking
Connecteurs pour équipements électroniques – Exigences de produit –
Partie 2-104: Connecteurs circulaires – Spécification particulière pour les connecteurs circulaires M8 à vis ou à encliquetage INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE W ICS 31.220.10 PRICE CODE CODE PRIX ISBN 978-2-8322-9670-3
– 2 – IEC 61076-2-104:2014 © IEC 2014 CONTENTS FOREWORD . 5 1 Scope . 8 2 Normative references . 8 3 Technical information . 9 3.1 Terms and definitions . 9 3.2 Recommended method of termination . 9 3.3 Number of contacts, ratings and characteristics . 9 3.4 Creepage and clearance distances . 9 3.5 Marking . 10 3.6 Safety aspects . 10 4 Dimensional information . 10 4.1 General . 10 4.2 Survey of styles and variants . 10
General . 10 4.2.1 Fixed connectors . 10 4.2.2 Free connectors . 12 4.2.34.3 Interface dimensions . 17
Pin front and side view A-coding . 17 4.3.1 Pin front view B-coding . 19 4.3.24.4 Engagement (mating) information . 20 4.5 Gauges . 21
Sizing gauges and retention force gauges . 21 4.5.15 Characteristics . 22 5.1 Climatic category . 22 5.2 Electrical characteristics . 22
Rated voltage – Rated impulse voltage – Pollution degree . 22 5.2.1 Voltage proof . 23 5.2.2 Current-carrying capacity . 23 5.2.3 Contact resistance . 23 5.2.4 Insulation resistance . 23 5.2.55.3 Mechanical characteristics . 24
Mechanical operation . 24 5.3.1 Insertion and withdrawal forces . 24 5.3.2 Contact retention in insert . 24 5.3.3 Polarizing method . 24 5.3.4 Vibration (sinusoidal) . 24 5.3.55.4 Other characteristics . 25
IP degree of protection . 25 5.4.16 Test schedule . 25 6.1 General . 25
Introductury remarks . 25 6.1.1 Arrangement for contact resistance measurements . 25 6.1.2 Arrangement for dynamic stress tests (vibration) . 26 6.1.36.2 Test schedule . 28
Test group P – Preliminary . 28 6.2.1 Test group AP – Dynamic/ Climatic . 29 6.2.2SIST EN 61076-2-104:2014
IEC 61076-2-104:2014 © IEC 2014 – 3 –
Test group BP – Mechanical endurance . 31 6.2.3 Test group CP – Electrical load . 33 6.2.4 Test group DP – Chemical resistivity . 34 6.2.5 Test group EP – Connection method tests . 34 6.2.6 (informative)
Diameter of the female connector body . 35 Annex A Figure 1 – Tube insert, male contacts dip solder mounting, long version . 11 Figure 2 – Tube insert, male contacts dip solder mounting, short version . 11 Figure 3 – Fixed connector with wire ends,
male contacts, single hole mounting . 11 Figure 4 – Fixed connector with wire ends,
female contacts, single hole mounting . 12 Figure 5 – Rewireable connector, male contacts,
straight version, with locking nut . 13 Figure 6 – Rewireable connector, male contacts,
right angled version, with locking nut . 13 Figure 7 – Non-rewireable connector, male contacts,
straight version, snap-locking . 14 Figure 8 – Non-rewireable connector, male contacts,
straight version, with locking nut . 14 Figure 9 – Non-rewireable connector, male contacts, right angled version, with locking nut . 14 Figure 10 – Rewireable connector, female contacts,
straight version, with locking nut . 15 Figure 11 – Rewireable connector, female contacts,
right angled version, with locking nut . 15 Figure 12 – Non-rewireable connector, female contacts,
straight version, snap-locking . 15 Figure 13 – Non-rewireable connector, female contacts, right angled version, snap-locking .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.