EN 60512-7-1:2010

Connectors for electronic equipment - Tests and measurements - Part 7-1: Impact tests (free connectors) - Test 7a: Free fall (repeated)

IEC 60512-7-1:2010 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to define a standard test method to assess the ability of a connector to withstand the impacts it would receive when dropped repeatedly.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 7-1: Aufprallprüfungen (freie Steckverbinder) - Prüfung 7a: Freier Fall (Falltrommel)

Connecteurs pour équipements électroniques - Essais et mesures - Partie 7-1: Essais d'impact (fiches) - Essai 7a: Chute libre (essai répété)

La CEI 60512-7-1:2010 est utilisée pour les essais des connecteurs du domaine d'activité du comité d'études 48, lorsque la spécification particulière l'exige. Elle peut également être utilisée pour des dispositifs similaires lorsqu'une spécification particulière le stipule. L'objet de cette norme est de définir une méthode d'essai normalisée pour évaluer l'aptitude d'un connecteur à supporter les impacts qu'il subirait si on le laissait tomber de manière répétée.

Konektorji za elektronsko opremo - Preskusi in meritve - 7-1. del: Udarni preskusi (prosti konektorji) - Preskus 7a: Prosti pad (ponavljajoči) (IEC 60512-7-1:2010)

Ta del IEC 60512, kadar ga zahteva podrobna specifikacija, se uporablja za preskušanje konektorjev v okviru tehničnega odbora 48. Lahko se uporablja tudi za podobne naprave, kadar ga določa podrobna specifikacija. Cilj tega standarda je opredeliti standardno preskusno metodo za vrednotenje zmožnosti konektorja, da je odporen na udarce pri ponavljajočem padu.

General Information

• Status: Published
• Publication Date: 20-May-2010
• Withdrawal Date: 30-Apr-2013
• ICS: 31.220.01 - Electromechanical components in general
• Technical Committee: CLC/SR 48B - Connectors
• Drafting Committee: IEC/SC 48B - IEC_SC_48B
• Parallel Committee: IEC/SC 48B - IEC_SC_48B
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 21-May-2010
• Completion Date: 21-May-2010
• Ref Project: SIST EN 60512-7-1:2010 - Connectors for electronic equipment - Tests and measurements - Part 7-1: Impact tests (free connectors) - Test 7a: Free fall (repeated) (IEC 60512-7-1:2010)

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2010
.RQHNWRUML]DHOHNWURQVNRRSUHPR3UHVNXVLLQPHULWYHGHO8GDUQLSUHVNXVL
SURVWLNRQHNWRUML3UHVNXVD3URVWLSDGSRQDYOMDMRþL,(&
Connectors for electronic equipment - Tests and measurements - Part 7-1: Impact tests
(free connectors) - Test 7a: Free fall (repeated) (IEC 60512-7-1:2010)
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 7-1:
Aufprallprüfungen (freie Steckverbinder) - Prüfung 7a: Freier Fall (Falltrommel) (IEC
60512-7-1:2010)
Connecteurs pour équipements électroniques - Essais et mesures - Partie 7-1: Essais
d'impact (fiches) - Essai 7a: Chute libre (essai répété) (CEI 60512-7-1:2010)
Ta slovenski standard je istoveten z: EN 60512-7-1:2010
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60512-7-1
NORME EUROPÉENNE
May 2010
EUROPÄISCHE NORM
ICS 31.220.01
English version
Connectors for electronic equipment -
Tests and measurements -
Part 7-1: Impact tests (free connectors) -
Test 7a: Free fall (repeated)
(IEC 60512-7-1:2010)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Essais et mesures - Mess- und Prüfverfahren -
Partie 7-1: Essais d'impact (fiches) - Teil 7-1: Aufprallprüfungen
Essai 7a: Chute libre (essai répété) (freie Steckverbinder) -
(CEI 60512-7-1:2010) Prüfung 7a: Freier Fall (Falltrommel)
(IEC 60512-7-1:2010)
This European Standard was approved by CENELEC on 2010-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-7-1:2010 E
Foreword
The text of document 48B/2016/CDV, future edition 1 of IEC 60512-7-1, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60512-7-1 on 2010-05-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-05-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60512-7-1:2010 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60512-7-1:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60512-1-1 - Connectors for electronic equipment - Tests EN 60512-1-1 -
and measurements -
Part 1-1: General examination - Test 1a:
Visual examination
ISO 48 2007 Rubber, vulcanized or thermoplastic - - -
Determination of hardness (hardness between
10 IRHD and 100 IRHD)
IEC 60512-7-1 ®
Edition 1.0 2010-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment – Tests and measurements –
Part 7-1: Impact tests (free connectors) – Test 7a: Free fall (repeated)

Connecteurs pour équipements électroniques – Essais et mesures –
Partie 7-1: Essais d’impact (fiches) – Essai 7a: Chute libre (essai répété)

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
G
CODE PRIX
ICS 31.220.01 ISBN 2-8318-1085-3
– 2 – 60512-7-1 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –
Part 7-1: Impact tests (free connectors) –
Test 7a: Free fall (repeated)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on te
...