EN IEC 61754-6:2022/A1:2026
(Amendment)Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 6: Type MU connector family
- Status
- Not Published
- Publication Date
- 03-Dec-2026
- Current Stage
- 5060 - Voting results sent to TC, SR - Formal Approval
- Start Date
- 18-Sep-2026
- Completion Date
- 18-Sep-2026
EN IEC 61754-6:2022/A1:2026 is a CLC amendment to the fibre optic connector interface standard for the Type MU connector family. It updates the interface geometry, grades and related references used to specify MU connector interfaces for fibre optic interconnecting devices and passive components. Engineers, manufacturers and test laboratories use it to align connector dimensions, grading and measurement methods.
What does EN IEC 61754-6:2022/A1:2026 specify?
EN IEC 61754-6:2022/A1:2026 specifies amendments to the Type MU connector family interface standard. Its focus is the MU connector interface geometry and the related grade and reference updates that support design, manufacturing and verification.
The amendment is organized around Clause 2, which updates normative references, and Clause 5, which updates the interface tables and Figure 8. The affected material covers simplex, duplex, APC and horizontal duplex plug connector interfaces.
What are the key requirements of EN IEC 61754-6:2022/A1:2026?
EN IEC 61754-6:2022/A1:2026 mainly tightens how MU connector interfaces are referenced, dimensioned and checked. The most important changes affect grade assignments, interface tables and the way several dimensions are measured in practice.
Normative references and grade mapping
- Clause 2 adds IEC 61755-3 (all parts) and IEC 63267-3 (all parts). These companion series provide the connector parameter sets that the grade tables point to, so users no longer rely on a single fixed set of values.
- In Tables 6, 8, 17 and 47, grade A is replaced with “Grade not specified at this time”, while grades B to D refer to the IEC 61755-3 series and grades B and C refer to the IEC 63267-3 series. In practice, this tells designers and buyers to match the connector grade to the appropriate fibre parameter family.
Dimensional updates for key interfaces
- Table 41 is replaced for the 6,25 mm duplex plug connector interface, and Table 42 is replaced for the 6,25 mm duplex plug connector interface grade data. These updates give the current reference dimensions for that interface, so tooling and gauge design can follow the revised geometry.
- Table 42 also adds the note that dome eccentricity of the spherically polished ferrule endface shall be less than 50 μm. For inspection, this gives a clear endface quality check.
- Table 11 changes the pin gauge entry LK to Ra: ≤0.000 2. This sets a very fine surface finish requirement on that gauge feature.
Assembly position, contact force and measurement conditions
- In the simplex, duplex and horizontal duplex tables, several footnotes change the letter references used for dimensions, and Table 39 and Table 40 also replace “EA” with “EC”. This keeps the APC interface notation aligned across the document.
- Table 41 and Table 42 state that a chamfer or radius is allowed to a maximum depth of 0,5 mm from the ferrule endface, and that the delatch housing shall move to the right or left. In practice, the same interface can be measured in connected or disconnected states, so the state must be identified during inspection.
- Table 41 and Table 42 also link ferrule compression force to the measured position shift between the optical datum target and the mechanical datum target. The compression force is measured according to IEC 61300-3-22. This gives laboratories a specific method for checking the contact behavior of the mated connector.
What terms does EN IEC 61754-6:2022/A1:2026 define?
EN IEC 61754-6:2022/A1:2026 uses several interface terms that matter for setting up and checking MU connectors.
- Ferrule - the part whose endface position and contact behavior are controlled by the interface dimensions.
- Optical datum target - the optical reference used together with the mechanical datum target to describe ferrule movement under compression.
- Mechanical datum target - the mechanical reference point used to define and measure the interface position.
- Delatch housing - the movable housing that can shift right or left and changes how some dimensions are interpreted.
- APC - the angled endface connector plug interface used in the APC tables and figure updates.
- Grade A / B / C / D - interface grade designations that are linked to companion IEC parameter series, with Grade A now shown as not specified at this time in several tables.
Who uses EN IEC 61754-6:2022/A1:2026?
EN IEC 61754-6:2022/A1:2026 is used by connector designers, fibre optic component manufacturers, test laboratories, quality teams and procurement engineers. They use it to specify MU interface geometry, select the right grade, build gauges and verify supplied parts against the defined interface dimensions.
It is relevant wherever Type MU fibre optic connector interfaces are designed, made or checked for fibre optic interconnecting devices and passive components.
What changed in EN IEC 61754-6:2022/A1:2026 from the previous edition?
EN IEC 61754-6:2022/A1:2026 amends IEC 61754-6 Edition 3.0 (2022-02).
- Clause 2 adds IEC 61755-3 (all parts) and IEC 63267-3 (all parts).
- Tables 5, 7, 39, 40 and 46 update footnote references from “L, M and V” to “I, P, Q and R”.
- Tables 6, 8, 17 and 47 revise grade assignments and remove the note that pointed to IEC 61755-6-1.
- Table 11 changes the LK pin gauge surface finish entry.
- Figure 8 is replaced.
- Tables 41 and 42 are replaced with new 6,25 mm duplex interface data.
- Table 43 changes the referenced companion standard in footnote b.
- The bibliography deletes IEC 61755-6-1.
Which standards are used with EN IEC 61754-6:2022/A1:2026?
EN IEC 61754-6:2022/A1:2026 uses companion IEC standards to define related connector parameters and test methods.
- IEC 61755-3 (all parts) - provides connector parameters for dispersion unshifted single-mode physically contacting fibres.
- IEC 63267-3 (all parts) - provides connector parameters for enhanced macro bend multimode fibres with 50 μm core diameter.
- IEC 63267-1 - is referenced in the updated 6,25 mm duplex grade table.
- IEC 61300-3-22 - provides the method used to measure ferrule compression force.
What does the EN IEC 61754-6:2022/A1:2026 document contain?
EN IEC 61754-6:2022/A1:2026 contains revised interface tables for simplex, duplex, APC and horizontal duplex MU connector interfaces, plus an updated sleeve holder figure. The tables give dimensions, grades, footnotes and reference points used for design and inspection.
It also contains the measurement notes that explain how to interpret ferrule compression, endface movement and delatch housing position. Those notes are the parts most often used when making gauges, checking drawings or verifying conformance in a laboratory.
Relations
- Effective Date
- 17-Nov-2026
- Effective Date
- 17-Nov-2026
- Effective Date
- 17-Nov-2026
- Effective Date
- 17-Nov-2026
- Effective Date
- 14-Jan-2025
Get Certified
Connect with accredited certification bodies for this standard

ANCE
Mexican certification and testing association.

Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.

LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
EN IEC 61754-6:2022/A1:2026 is a draft published by CLC. Its full title is "Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 6: Type MU connector family". This standard covers: Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 6: Type MU connector family
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 6: Type MU connector family
EN IEC 61754-6:2022/A1:2026 is classified under the following ICS (International Classification for Standards) categories: 33.180.20 - Fibre optic interconnecting devices. The ICS classification helps identify the subject area and facilitates finding related standards.
EN IEC 61754-6:2022/A1:2026 has the following relationships with other standards: It is inter standard links to EN IEC 61755-3-2:2024, EN IEC 63267-3-61:2025, EN IEC 63267-3-81:2025, EN IEC 61755-3-1:2024, EN IEC 61754-6:2022. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN IEC 61754-6:2022/A1:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61754-6:2022/oprA1:2025
01-december-2025
Optični spojni elementi in pasivne komponente - Vmesniki za optične konektorje -
6. del: Konektorska družina vrste MU - Dopolnilo A1
Fibre optic interconnecting devices and passive components - Fibre optic connector
interfaces - Part 6: Type MU connector family
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von
Lichtwellenleiter-Steckverbindern - Teil 6: Steckverbinderfamilie der Bauart MU
Dispositifs d’interconnexion et composants passifs fibroniques - Interfaces de
connecteurs fibroniques - Partie 6: Famille de connecteurs de type MU
Ta slovenski standard je istoveten z: EN IEC 61754-6:2022/prA1:2025
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 61754-6:2022/oprA1:2025 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN IEC 61754-6:2022/oprA1:2025
SIST EN IEC 61754-6:2022/oprA1:2025
86B/5125/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61754-6/AMD1 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2025-10-17 2026-01-09
SUPERSEDES DOCUMENTS:
86B/4997/CD, 86B/5034A/CC
IEC SC 86B : FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS
SECRETARIAT: SECRETARY:
Japan Mr Ryo Koyama
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Amendment 1 - Fibre optic interconnecting devices and passive components - Fibre optic
connector interfaces - Part 6: Type MU connector family
PROPOSED STABILITY DATE: 2032
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
SIST EN IEC 61754-6:2022/oprA1:2025
IEC CDV 61754-6/AMD1 © IEC 2025
1 INTERNATIONAL ELECTROTECHNICAL COMMISSION
3 _____________
5 IEC 61754-6
6 Edition 3.0 2022-02
7 Fibre optic interconnecting devices and passive components – Fibre optic connector
8 interfaces - Part 6: Type MU connector family
9 AMENDMENT 1
10 2 Normative references
11 Add the following references:
12 IEC 61755-3 (all parts), Fibre optic interconnecting devices and passive components - Connector optical interfaces:
13 Connector parameters of dispersion unshifted single-mode physically contacting fibres
14 IEC 63267-3 (all parts), Fibre optic interconnecting devices and passive components – Connector optical interfaces
15 for enhanced macro bend multimode fibres: Connector parameters of physically contacting 50 µm core diameter
16 fibres
18 5 Interfaces
19 Table 5 – Dimensions of the simplex plug connector interface
20 In footnote b, replace “L, M and V” with “I, P, Q and R”.
22 Table 6 – Grade of the simplex plug connector
23 In the row for grade A, replace the content in the second and third column with “Grade not
24 specified at this time”.
25 In the rows for grades B to D, replace the content in the second and third column with “Refer to
26 IEC 61755-3 series”.
27 In the rows for grades B and C , replace the minimum and maximum values or the text with
m m
28 “Refer to IEC 63267-3 series”.
29 Delete note b “See IEC 61755-6-1 for guidance”.
31 Table 7 – Dimensions of the 4,5 mm duplex plug connector interface
32 In footnote b, replace “L, M and V” with “I, P, Q and R”.
SIST EN IEC 61754-6:2022/oprA1:2025
IEC CDV 61754-6/AMD1 © IEC 2025
35 Table 8 – Grade of the 4,5 mm duplex plug connector
36 In the row for grade A, replace the content in the second and third column with “Grade not
37 specified at this time”.
38 In the rows for grades B to D, replace the content in the second and third column with “Refer to
39 IEC 61755-3 series”.
40 In the rows for grades B and C , replace the minimum and maximum values or the text with
m m
41 “Refer to IEC 63267-3 series”.
42 Delete note b “See IEC 61755-6-1 for guidance”.
44 Table 11 – Pin gauge dimensions
45 In the last column, row LK, replace “grade N4 (0,2 μm radius)” with “Ra: ≤0.000 2”.
47 Table 17 – Grade of the plug connector
48 In the row for grade A, replace the content in the second and third column with “Grade not
49 specified at this time”.
50 In the rows for grades B to D, replace the content in the second and third column with “Refer to
51 IEC 61755-3 series”.
52 In the rows for grades B and C , replace the minimum and maximum values or the text with
m m
53 “Refer to IEC 63267-3 series”.
54 Delete note b “See IEC 61755-6-1 for guidance”.
56 Figure 8 – Sleeve holder int
...



