CLC/TS 50131-3:2003

Alarm systems - Intrusion systems - Part 3: Control and indicating equipment

see BT117/SG5336/INF * EN procedure to begin July 2005 * Standstill maintained * Superseded by EN 50131-3:2009

Alarmanlagen - Einbruchmeldeanlagen - Teil 3: Melderzentrale

Systèmes d'alarme - Systèmes d'alarme intrusion - Partie 3: Matériel de commande et d'affichage (Centrale d'alarme)

Alarm systems - Intrusion systems -- Part 3: Control and indicating equipment

General Information

• Status: Withdrawn
• Publication Date: 30-Jul-2003
• ICS: 13.310 - Protection against crime
• Technical Committee: CLC/TC 79 - Alarm systems
• Drafting Committee: CLC/TC 79 - Alarm systems
• Parallel Committee: IEC/TC 79 - IEC_TC_79
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 01-Feb-2012
• Completion Date: 01-Feb-2012
• Ref Project: SIST-TS CLC/TS 50131-3:2004 - Alarm systems - Intrusion systems -- Part 3: Control and indicating equipment

Relations

• Replaced By: EN 50131-3:2009 - Alarm systems - Intrusion and hold-up systems - Part 3: Control and indicating equipment
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2004
Alarm systems - Intrusion systems -- Part 3: Control and indicating equipment
Alarm systems - Intrusion systems -- Part 3: Control and indicating equipment
Alarmanlagen - Einbruchmeldeanlagen -- Teil 3: Melderzentrale
Systèmes d'alarme - Systèmes d'alarme intrusion -- Partie 3: Matériel de commande et
d'affichage (Centrale d'alarme)
Ta slovenski standard je istoveten z: CLC/TS 50131-3:2003
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION  CLC/TS 50131-3
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION July 2003

ICS 13.310
English version
Alarm systems –
Intrusion systems
Part 3: Control and indicating equipment

Systèmes d’alarme– Alarmanlagen –
Systèmes d’alarme intrusion Einbruchmeldeanlagen
Partie 3: Matériel de commande et Teil 3: Melderzentrale
d’affichage (Centrale d’alarme)

This Technical Specification was approved by CENELEC on 2003-05-19.

CENELEC members are required to announce the existence of this TS in the same way as for an EN and
to make the TS available promptly at national level in an appropriate form. It is permissible to keep
conflicting national standards in force.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. CLC/TS 50131-3:2003 E

Foreword
The text of this Technical Specification was prepared by the Technical Committee CENELEC TC 79,
Alarm systems.
The text of the draft was submitted to the formal vote and was approved by CENELEC as
CLC/TS 50131-3 on 2003-05-19.
The following date was fixed:
– latest date by which the existence of the CLC/TS
has to be announced at national level (doa) 2003-10-30
__________
- 3 - CLC/TS 50131-3:2003
Contents
Page
1 Scope .6
2 Normative references .6
3 Definitions and abbreviations .7
3.1 Definitions.7
3.2 Abbreviations.12
4 Equipment attributes.12
4.1 General.12
4.2 Functionality .12
5 CIE structure.13
6 Security grade.13
7 Environmental requirements .14
7.1 General.14
7.2 Environmental class I: Indoor.14
7.3 Environmental class II: Indoor - General.14
7.4 Environmental class III: Outdoor - Sheltered .14
7.5 Environmental class IV: Outdoor - General.14
7.6 Special condition .14
7.7 Environmental tests.14
8 Functional requirements.14
8.1 Inputs.14
8.2 Operation.15
8.3 Processing .22
8.4 Indication.25
8.5 Notification outputs.28
8.6 Tamper security (detection/protection).29
8.7 Fault .30
8.8 Interconnections.31
8.9 Timing .31
8.10 Event recording .32
8.11 Power supply.33
9 Electrical safety .33
10 Product documentation.34
10.1 Installation and maintenance .34
10.2 Operating instructions .34
11 Marking and labelling.35
12 Tests.35
12.1 Test conditions .35
12.2 Functional tests .36
12.3 Reduced functional test.36
12.4 Functional tests .37
12.5 Access level .48
12.6 Authorization requirements .49

13 Environmental tests.58
13.1 General.58
13.2 Environmental test selection .59

Annexes
Annex A (informative) Interconnection types.64
Annex B (informative) Example of calculation for code variations .66
Annex C (informative) Summary of timing requirements.68

Figures
Figure A.1 – Specific wired interconnections.65
Figure A.2 – Non specific wired interconnections.66
Figure A.3 – Wire-free interconnections.66

Tables
Table 1 - Access level to functions and control .16
Table 2 - Authorization requirements - Access levels 2, 3, and 4 .16
Table 3 – Detection of repeated incorrect authorisation codes .17
Table 4 - Prevention of setting conditions.18
Table 5 - Overriding of prevention of setting conditions .18
Table 6 - Authorisation required to restore conditions.20
Table 7 - Automatic inhibit .20
Table 8 - Manual inhibit .21
Table 9 - Processing of intruder, hold-up, tamper alarm and fault signals/messages .23
Table 10 - Monitoring of processing .24
Table 11– Indication (from Table 4 of EN 50131-1) .26
Table 12 – Additional indication in the CIE or ACE .27
Table 13 - Notification requirements.28
Table 14 - Tamper protection .29
Table 15 - Tamper detection .29
Table 16– Tool dimension for tamper detection .30
Table 17– Removal from mounting .30
Table 18 - Recognition of fault conditions .30
Table 19 - Interconnection confirmation .31
Table 20 - Reduced functional test.37
Table 21 – Functional tests.38
Table 22 – Tests of the processing of hold-up signal or messages .39
Table 23 – Tests of the processing of tamper signal or messages.41
Table 24 – Test of the process monitoring .45
Table 25 – Test of processing of fault signals or messages .46
Table 26 – Test of processing of optional functions (non specified in EN 50131-1) .48

- 5 - CLC/TS 50131-3:2003
Table 27 – Test of the access to the functions and controls .48
Table 28 – Test for disabling user input during incorrect authorization codes .51
Table 29 – Test for generation of tamper during incorrect authorization codes .52
Table 30 – Test of setting procedure.53
Table 31 – Test for unsetting procedure.54
Table 32 – Test of Entry Route Procedure .55
Table 33 – Test of exit route procedure.56
Table 34 – Test of Event Log .
...