FprEN IEC 60317-0-3:2024
(Main)Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminium wire
Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminium wire
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-3: Allgemeine Anforderungen - Lackisolierte Runddrähte aus Aluminium
Spécifications pour types particuliers de fils de bobinage - Partie 0-3: Exigences générales - Fil de section circulaire en aluminium émaillé
Specifikacije za posebne vrste navijalnih žic - 0-3. del: Splošne zahteve - Emajliran okrogel aluminijev vodnik
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 60317-0-3:2023
01-oktober-2023
Specifikacije za posebne vrste navijalnih žic - 0-3. del: Splošne zahteve - Emajliran
okrogel aluminijev vodnik
Specifications for particular types of winding wires - Part 0-3: General requirements -
Enamelled round aluminium wire
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-3:
Allgemeine Anforderungen - Lackisolierte Runddrähte aus Aluminiumdraht
Spécifications pour types particuliers de fils de bobinage - Partie 0-3: Exigences
générales - Fil de section circulaire en aluminium émaillé
Ta slovenski standard je istoveten z: prEN IEC 60317-0-3:2023
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN IEC 60317-0-3:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN IEC 60317-0-3:2023
oSIST prEN IEC 60317-0-3:2023
55/2003/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60317-0-3 ED4
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2023-08-25 2023-11-17
SUPERSEDES DOCUMENTS:
55/1942/RR
IEC TC 55 : WINDING WIRES
SECRETARIAT: SECRETARY:
United States of America Mr Mike Leibowitz
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
TC 2,TC 14
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In So me
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Specifications for particular types of winding wires - Part 0-3: General requirements -
Enamelled round aluminium wire
PROPOSED STABILITY DATE: 2026
NOTE FROM TC/SC OFFICERS:
This new 4th edition proposes simple amendments to the springiness and cut-through requirements in
accordance with Decision 2022-08 in 55/1936/DL, and with 55/1912A/INF.
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, or any part of it, for
any other purpose without permission in writing from IEC.
oSIST prEN IEC 60317-0-3:2023
IEC CDV 60317-0-3/Ed4 © IEC 2023 – 2 – 55/2003/CDV
1 CONTENTS
3 FOREWORD . 4
4 INTRODUCTION . 6
5 1 Scope . 7
6 2 Normative references . 7
7 3 Terms, definitions, general notes, and appearance . 7
8 3.1 Definitions . 7
9 3.2 General notes . 8
10 3.2.1 Methods of test . 8
11 3.2.2 Winding wire . 9
12 3.3 Appearance . 9
13 4 Dimensions . 9
14 4.1 Conductor diameter . 9
15 4.2 Out of roundness of conductor . 11
16 4.3 Minimum increase in diameter due to the insulation and the bonding layer . 11
17 4.3.1 Enamelled wires without a bonding layer . 11
18 4.3.2 Enamelled wires with a bonding layer . 11
19 4.4 Maximum overall diameter . 11
20 4.4.1 Enamelled wires without a bonding layer . 11
21 4.4.2 Enamelled wires with a bonding layer . 11
22 5 Electrical resistance . 12
23 6 Elongation . 12
24 7 Springiness . 12
25 8 Flexibility and adherence . 12
26 8.1 Mandrel winding test (nominal conductor diameters up to and including
27 1,600 mm) . 12
28 8.2 Stretching test (nominal conductor diameters over 1,000 mm) . 12
29 8.3 Jerk test (nominal conductor diameters up to and including 1,000 mm) . 13
30 8.4 Peel test (nominal conductor diameters over 1,000 mm) . 13
31 9 Heat shock . 13
32 9.1 Nominal conductor diameters up to and including 1,600 mm . 13
33 9.2 Nominal conductor diameters over 1,600 mm . 13
34 10 Cut-through . 13
35 11 Resistance to abrasion . 13
36 12 Resistance to solvents . 13
37 13 Breakdown voltage . 13
38 13.1 General . 13
39 13.2 Nominal conductor diameters up to and including 2,500 mm . 14
40 13.3 Nominal conductor diameters over 2,500 mm . 14
41 14 Continuity of insulation (nominal conductor diameters up to and including
42 1,600 mm) . 14
43 15 Temperature index . 15
44 16 Resistance to refrigerants . 15
45 17 Solderability . 15
oSIST prEN IEC 60317-0-3:2023
IEC CDV 60317-0-3/Ed4 © IEC 2023 – 3 – 55/2003/CDV
46 18 Heat or solvent bonding . 15
47 19 Dielectric dissipation factor . 15
48 20 Resistance to transformer oil . 15
49 21 Loss of mass . 15
50 23 Pin hole test . 15
51 30 Packaging . 16
52 Annex A (informative) Dimensions for intermediate nominal conductor diameters
53 (R 40) . 17
54 A.1 General . 17
55 A.2 Enamelled wires without a bonding layer . 17
56 A.3 Enamelled wires with a bonding layer . 18
57 Annex B (normative) Method for the calculation of linear resistance . 19
58 Annex C (informative) Resistance . 20
60 Table 1 – Dimensions of enamelled wires (R 20) . 10
61 Table 2 – Dimensions of enamelled wires with a bonding layer (R 20) . 11
62 Table 3 – Elongation . 12
63 Table 4 – Mandrel winding . 12
64 Table 5 – Heat shock . 13
65 Table 6 – Breakdown voltage . 14
66 Table 7 – Breakdown voltage . 14
67 Table 8 – Continuity of insulation . 15
68 Table A.2 – Dimensions of enamelled wires with a bonding layer (R 40) . 18
69 Table C.1 – Electrical resistances . 20
oSIST prEN IEC 60317-0-3:2023
IEC CDV 60317-0-3/Ed4 © IEC 2023 – 4 – 55/2003/CDV
72 INTERNATIONAL ELECTROTECHNICAL COMMISSION
73 ____________
75 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
77 Part 0-3: General requirements – Enamelled round aluminium wire
79 FOREWORD
80 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
81 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
82 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
83 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
84 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
85 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
86 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
87 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
88 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
89 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
90 consensus of opinion on the relevant subjects since each technical committee has representation from all
91 interested IEC National Committees.
92 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
93 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
94 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
95 misinterpretation by any end user.
96 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
97 transparently to the maximum extent possible in their national and regional publications. Any divergence between
98 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
99 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
100 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
101 services carried out by independent certification bodies.
102 6) All users should ensure that they have the latest edition of this publication.
103 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
104 members of its technical committees and IEC National Committees for any personal injury, property damage or
105 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
106 expenses arising out of the publication, use of, or reliance upon, this IEC
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.