iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61558-2-6:1997

(Main)

Safety of power transformers, power supply units and similar - Part 2-6: Particular requirements for safety isolating transformers for general use

Safety of power transformers, power supply units and similar - Part 2-6: Particular requirements for safety isolating transformers for general use

This part 2 of EN 61558 applies to stationary or portable, single-phase or polyphase, air-cooled safety isolating transformers associated or otherwise. It has the status of a group safety publication in accordance with IEC Guide 104. This part 2 supplements or modifies the corresponding clauses in EN 61558-1.

Sicherheit von Transformatoren, Netzgeräten und dergleichen - Teil 2-6: Besondere Anforderungen an Sicherheitstransformatoren für allgemeine Anwendungen

Sécurité des transformateurs, blocs d'alimentation et analogues - Partie 2-6: Règles particulières pour les transformateurs de sécurité pour usage général

La présente partie 2 de la EN 61558 est applicable aux transformateurs de sécurité, fixes ou mobiles, monophasés ou polyphasés, à refroidissement par air, associés ou non. Elle a le statut de publication groupée de sécurité conformément au guide CEI 104 La présente partie 2 complète ou modifie les articles correspondants de la EN 61558-1,

Safety of power transformers, power supply units and similar - Part 2-6: Particular requirements for safety isolating transformers for general use (IEC 61558-2-6:1997)

General Information

Status
Withdrawn
Publication Date
02-Nov-1997
Withdrawal Date
31-Jul-2000
ICS
29.180 - Transformers. Reactors
Technical Committee
CLC/SR 96 - Small power transformers, reactors, power supply units and similar products
Drafting Committee
IEC/TC 96 - IEC_TC_96
Parallel Committee
IEC/TC 96 - IEC_TC_96
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Jul-2012
Completion Date
01-Jul-2012
Directive
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
73/23/EEC - Electrical equipment designed for use within certain voltage limits
Ref Project
SIST EN 61558-2-6:1999 - Safety of power transformers, power supply units and similar -- Part 2-6: Particular requirements for safety isolating transformers for general use

Relations

Replaces
EN 60742:1995 - Isolating transformers and safety isolating transformers - Requirements
Effective Date
29-Jan-2023
Replaced By
EN 61558-2-6:2009 - Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
Effective Date
29-Jan-2023

Buy Standard

EN 61558-2-6:1999EN 61558-2-6:1999
PreviousNext
Standard
EN 61558-2-6:1999
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61558-2-6:1999
01-julij-1999
Safety of power transformers, power supply units and similar - Part 2-6: Particular
requirements for safety isolating transformers for general use (IEC 61558-2-6:1997)
Safety of power transformers, power supply units and similar -- Part 2-6: Particular
requirements for safety isolating transformers for general use
Sicherheit von Transformatoren, Netzgeräten und dergleichen -- Teil 2-6: Besondere
Anforderungen an Sicherheitstransformatoren für allgemeine Anwendungen
Sécurité des transformateurs, blocs d'alimentation et analogues -- Partie 2-6: Règles
particulières pour les transformateurs de sécurité pour usage général
Ta slovenski standard je istoveten z: EN 61558-2-6:1997
ICS:
29.180 Transformatorji. Dušilke Transformers. Reactors
SIST EN 61558-2-6:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

NORME
CEI
INTERNATIONALE
IEC
61558-2-6
INTERNATIONAL
Première édition
STANDARD
First edition
1997-02
PUBLICATION GROUPÉE DE SÉCURITÉ
GROUP SAFETY PUBLICATION
Sécurité des transformateurs, blocs d'alimentation
et analogues –
Partie 2:
Règles particulières pour les transformateurs
de sécurité pour usage général
Safety of power transformers, power supply units
and similar –
Part 2:
Particular requirements for safety isolating
transformers for general use
 IEC 1997 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni utilisée No part of this publication may be reproduced or utilized in
sous quelque forme que ce soit et par aucun procédé, électronique any form or by any means, electronic or mechanical, including
ou mécanique, y compris la photocopie et les microfilms, sans photocopying and microfilm, without permission in writing from
l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE L
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 2 ----------------------

61558-2-6 © IEC:1997 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_________
SAFETY OF POWER TRANSFORMERS, POWER SUPPLY UNITS
AND SIMILAR −
Part 2: Particular requirements for safety isolating transformers
for general use
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61558-2-6 has been prepared by IEC technical committee 96: Small
power transformers, reactors and power supply units and special transformers, reactors and
power supply units: Safety requirements.
It has the status of a group safety publication in accordance with IEC Guide 104: Guide
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 62041:2020(Main)
Transformers, power supplies, reactors and similar products - EMC requirements
SIST EN IEC 62041:2020

IEC 62041: 2017(E) is applicable to transformers, reactors and power supply units covered by the IEC 61558 series of standards. This document deals with the electromagnetic compatibility requirements for emission and immunity within the frequency range 0 Hz to 400 GHz. No tests need to be performed at frequencies where no requirements are specified. This third edition cancels and replaces the second edition published in 2010. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:  
the inclusion of a clause on tests in series production;
the inclusion of a new clause on measurement uncertainly, and
the status of a harmonized standard for this third edition.  It has the status of a product family EMC standard in accordance with IEC Guide 107:2009, Electromagnetic compatibility – Guide to the drafting of electromagnetic compatibility publications.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61558-1:2019(Main)
Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests
SIST EN IEC 61558-1:2019

NEW!IEC 61558-1:2017 is available as IEC 61558-1:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61558-1:2017 deals with safety aspects of transformers, reactors, power supply units and combinations thereof such as electrical, thermal and mechanical safety. This document covers the following independent or associated stationary or portable types of dry-type transformers, power supply units, including switch mode power supply units, reactors and combinations thereof in the field of safety. The windings can be encapsulated or non-encapsulated. They are not forming a part of the distribution network. This third edition cancels and replaces the second edition published in 2005 and Amendment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a. fully insulated winding wires (FIW), new tables and aging tests for FIW constructions, b. overvoltage categories 1, 2, 3 and 4 for clearances and dielectric strength tests (new tables) are included, c. development of new symbols for the different overvoltage categories, d. symbol for maximum altitudes, if higher than 2 000 m, e. symbol for plug in power supply units, if the pins are damaged (tumbling barrel test), f. symbol for minimum temperature (even during the transportation), g. alternative temperature measurement, simulated load and back to back method according to IEC 60076-11, h. short circuit and overload protection, simulated load and back to back method according to IEC 60076-11, i. adjustment of temperatures in Table 2 according to CENELEC Guide 29, j. establishing partial discharge test above 750 V for FIW constructions, k. requirements for toroidal core constructions, division for basic and for supplementary isolation, l. modification of protection indexes for enclosures (IP-code), m. dimensioning of rectangular cross section connectors for transformers, n. repetition test, 80% of required dielectric strength test voltage of Table 14,a. o. vibration test for vehicles and railway applications, p. two Y1 Capacitors for working voltages above 250 V and not exceeding 500 V with overvoltage category 3. It has the status of a group safety publication in accordance with IEC Guide 104.

  • Standard
    183 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-10:2014(Main)
Safety of transformers, reactors, power supply units and combinations thereof - Part 2-10: Particular requirements and tests for separating transformers with high insulation level and separating transformers with output voltages exceeding 1 000 V
SIST EN 61558-2-10:2014

IEC 61558-2-10:2014 deals with the safety of separating transformers with high insulation level and separating transformers with output voltages exceeding 1 000 V. Transformers incorporating electronic circuits are also covered by this standard. This first edition cancels and replaces Chapter ll Section Three of IEC 60989 published in 1991. It constitutes a technical revision. The main changes consist of a) updating this part in accordance with IEC 61558-1:2005, and b) adding power supply units to the scope. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. The transitional period is not longer than 3 years after the publication of this standard.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-16:2009/A1:2013(Amendment)
Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units
SIST EN 61558-2-16:2010/A1:2014

2013-08-19: Publication allocated to tnaqvi@cencenelec.eu

  • Amendment
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-26:2013(Main)
Safety of transformers, reactors, power supply units and combinations thereof - Part 2-26: Particular requirements and tests for transformers and power supply units for saving energy and other purposes
SIST EN 61558-2-26:2014

IEC 61558-2-26:2013 deals with the safety of transformers, power supply units and switch mode power supply units all for saving energy and other purposes in electrical installations by adjusting the output voltage and/or other electrical characteristics on the output circuits without interruption affected by the transformers, power supply unit and switch mode power supply unit. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip them for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-14:2013(Main)
Safety of transformers, reactors, power supply units and combination thereof - Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers
SIST EN 61558-2-14:2013

IEC 61558-2-14:2012 deals with safety of variable transformers for general applications and power supply units incorporating variable transformers for general applications. Transformers incorporating electronic circuits are also covered by this standard. This first edition cancels and replaces the chapter IV of the IEC 60989 published in 1991. It is a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) update of the existing text; b) complete editorial review. This part has the status of a group safety publication in accordance with IEC Guide 104:2010. The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-15:2012(Main)
Safety of transformers, reactors, power supply units and combinations thereof - Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations
SIST EN 61558-2-15:2012

IEC 61558-2-15:2011 deals with safety aspects of isolating transformers for the supply of medical locations. This second edition cancels and replaces the first edition published in 1999. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104:2010. The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. This publication is to be read in conjunction with IEC 61558-1:2005.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-12:2011(Main)
Safety of transformers, reactors, power supply units and combinations thereof - Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage
SIST EN 61558-2-12:2011

IEC 61558-2-12:2011 deals with the safety of constant voltage transformers for general applications and power supply units for constant voltage for general applications. Constant voltage transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 2001. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2009. This part has the status of a group safety publication in accordance with IEC Guide 104: The preparation of safety publications and the use of basic safety publications and group safety publications. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-20:2011(Main)
Safety of transformers, reactors, power supply units and combinations thereof - Part 2-20: Particular requirements and tests for small reactors
SIST EN 61558-2-20:2011

IEC 61558-2-20:2010 deals with the safety of small reactors for general applications. This part is applicable to stationary or portable, single-phase or polyphase, air-cooled (natural or forced) general purpose reactors including alternating current, premagnetised and current compensated independent or associated reactors. This second edition cancels and replaces the first edition published in 2000. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61558-2-9:2011(Main)
Safety of transformers, reactors, power supply units and combinations thereof - Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps
SIST EN 61558-2-9:2011

IEC 61558-2-9:2010 deals with the safety of transformers for class III handlamps for tungsten filament lamps and power supply units incorporating transformers for class III handlamps for tungsten filament lamps. Transformers incorporating electronic circuits are also covered by this standard. This second edition cancels and replaces the first edition published in 2002. It constitutes a technical revision. The main changes consist of updating this part in accordance with IEC 61558-1:2005, and adding power supply units to the scope. This part has the status of a group safety publication in accordance with IEC Guide 104. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months from the date of publication. In the meantime, the previous edition can still be ordered by contacting your local IEC member National Committee or the IEC Central Office.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day