Sound system equipment - Part 12: Application of connectors for broadcast and similar use

Applies to circular and concentric connectors to be used for the interconnection of sound system components for broadcast and similar use, gives the applications and contact arrangement and contact designation for these connectors.

Elektroakustische Geräte - Teil 12: Anwendung von Steckverbindern für Rundfunk-Studiobetrieb und ähnliche Zwecke

Equipements pour systèmes électroacoustiques - Partie 12: Application des connecteurs pour radiodiffusion et usage analogue

S'applique aux connecteurs circulaires et concentriques utilisés pour l'interconnexion des éléments de systèmes électroacoustiques pour la radiodiffusion et usage analogue; elle décrit leurs utilisations ainsi que la disposition et la désignation de leurs contacts.

Sound system equipment -- Part 12: Application of connectors for broadcast and similar use (IEC 60268-12:1987 + A1:1991)

General Information

Status
Published
Publication Date
19-Feb-1995
Withdrawal Date
20-Aug-1995
Current Stage
6060 - Document made available - Publishing
Start Date
20-Feb-1995
Completion Date
20-Feb-1995

Relations

Buy Standard

Standard
EN 60268-12:1999
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-1999
Sound system equipment -- Part 12: Application of connectors for broadcast and
similar use (IEC 60268-12:1987 + A1:1991)
Sound system equipment -- Part 12: Application of connectors for broadcast and similar
use
Elektroakustische Geräte -- Teil 12: Anwendung von Steckverbindern für Rundfunk-
Studiobetrieb und ähnliche Zwecke
Equipements pour systèmes électroacoustiques -- Partie 12: Application des
connecteurs pour radiodiffusion et usage analogue
Ta slovenski standard je istoveten z: EN 60268-12:1995
ICS:
33.160.50 Pribor Accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEI
NORME
INTERNATIONALE IEC
268-12
INTERNATIONAL
Deuxième édition
STAN DARD
Second edition
1987-03
Equipements pour systèmes électroacoustiques
Douzième partie:
Application des connecteurs pour radiodiffusion
et usage analogue
Sound system equipment
Part 12:
Application of connectors for Broadcast
and similar use
Droits de reproduction réservés — Copyright - all rights reserved
© IEC 1987
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
3, rue de Varembé Geneva, Switzerland
International Electrotechnical Commission
IEC web site http: //www.iec.ch
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch
CODE PRIX
Commission Electrotechnique Internationale
H
PRICE CODE
International Electrotechnical Commission
IEC MemayHapoaHaa 3nenrporexHHVecKan HoMHCCHta
Pour prix, voir catalogue en vigueur
• • For price, see current catalogue

0 IEC 1987 — 3—
268-12
CONTENTS
Page
FOREWORD
PREFACE 5
Clause
1. Scope
2. Object
3. General 7
4. Application and contact designation 7
SECTION ONE — CIRCULAR CONNECTORS
5. Types of connectors and their application 9
6. Connection data 11
SECTION TWO — CONCENTRIC CONNECTORS
7. Type of connectors and their application 13
8. Polarity 15
268-12 IEC1987 - 5 -
INTERNATIONAL ELECTROTECHNICAL COMMISSION
SOUND SYSTEM EQUIPMENT
Part 12: Application of connectors for broadcast
and similar use
FOREWORD
The formal decisions or agreements of the I E C on technical matters, prepared by Technical Committees on which all the
1)
ational consensus
National Committees having a special interest therein are represented, express, as nearly as possible, an inte rn
of opinion on the subjects dealt with.
2) They have the form of recommendations for international use and they are accepted by the National Committees in that
sense.
In order to promote international unification, the I E C expresses the wish that all National Committees should adopt the text of
3)
the I E C recommendation for their national rules in so far as national conditions will permit. Any divergence between the I E C
recommendation and the corresponding national rules should, as far as possible, be clearly indicated in the latter.
The I E C has not laid down any procedure concerning marking as an indication of approval and has no responsibility when an
4)
item of equipment is declared to comply with one of its recommendations.
PREFACE
This standard has been prepared by I E C Technical Committee No. 84: Equipment and Systems in the Field of Audio, Video
and Audiovisual Engineering.
This second edition replaces the first edition of I E C Publication 268-12 (1975).
The text of this report is based on the first edition and the following documents:
rt on Voting Two Months' Procedure Report on Voting
Six Months' Rule Repo
29B(CO)117 84(CO)6 84(CO)10 84(CO)17
Further information can be found in the relevant Reports on Voting indicated in the table above.
The following I E C publications are quoted in this standard:
Publications Nos. 65 (1985): Safety Requirements for Mains Operated Electronic and Related Apparatus for Household
and Similar General Use.
130-8 (1976): Connectors for Frequencies below 3 MHz, Part 8: Concentric Connectors for Audio Circuits
in Radio Receivers.
130-9 (1971): Part 9: Circular Connectors for Radio and Associated Sound Equipment.
268-2 (1971): Sound System Equipment, Part 2: Explanation of General Terms.
4: Microphones
268-4 (1972): Pa rt
rt 11: Application of Circular Connectors for the Interconnection of Sound System
268-11 (1981): Pa
Components.
268-15 (1978): Part 15: Preferred Matching Values for the Interconnection of Sound System Compo-
nents.
I E C 1987 — 7 —
268-12 ©
SOUND SYSTEM EQUIPMENT
Part 12: Application of connectors for broadcast
and similar use
Scope
1.
This standard applies to circular and concentric connectors to be used for the interconnection of
sound system components for broadcast and similar use and gives the applications and also the
contact arrangement and contact designation for these connectors.
2. Object
In sound systems for broadcast and similar use it is often necessary to connect pieces of
equipment from different manufacturers and even from various countries in order to achieve
desired objectives.
General
3.
3.1 The connectors shall comply with the electrical and mechanical requirements given in I E C
Publications:
– 130-8: Connectors for Frequencies below 3 MHz, Part 8: Concentric Connectors for Audio
Circuits in Radio Receivers;
– 130-9: Part 9: Circular Connectors for Radio and Associated Sound Equipment.
3.2 For safety considerations, reference is required to I E C Publication 65: Safety Requirements for
Mains Operated Electronic and Related Apparatus for Household and Similar General Use.
Notes 1. – The preferred electrical matching values for the interconnection of sound system components are given in I E C
Publication 268-15: Sound System Equipment, Part 15: Preferred Matching Values for the Interconnection of
Sound System Components.
2. – Connectors for the interconnection of sound system components for other applications are dealt with in I E C
Publication 268-11: Pa rt 11: Application of Circular Connectors for the Interconnection of Sound System
Components.
For applications other than those given in this standard, reference is required to I E C Publications 130-8 and
3. –
130-9. At present not all connectors referred to in this standard are included in these publications.
4. Application and contact designation
For circular connectors, the contact arrangement and application shall be as given in Table I and
the contact designation shall be as given in Table II. For concentric connectors the contact
arrangement and application shall be as given in Table III and the contact designation shall be as
given in Table IV.
— 9 —
268-12 IECC 1987
4.1 Terminology for concentric connectors
In Table III, the following types of connectors are identified:
– '/a in B-gauge concentric connector;
– 4.4 mm Bantam concentric connector.
SECTION ONE: CIRCULAR CONNECTOR
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.