FprEN IEC 60034-9:2021
(Main)Rotating electrical machines - Part 9: Noise limits
Rotating electrical machines - Part 9: Noise limits
IEC 60034-9:2021 specifies test methods for the determination of sound power level of rotating electrical machines and specifies maximum A-weighted sound power levels for factory acceptance testing of network-supplied, rotating electrical machines in accordance with lEC 60034-1, having methods of cooling according to lEC 60034-6 and degrees of protection according to lEC 60034-5, and having the following characteristics: - standard design, either AC or DC, without additional special electrical, mechanical, or acoustical modifications intended to reduce the sound power level - rated output from 1 kW (or kVA) up to and including 5 500 kW (or kVA) - rated speed not greater than 3 750 min–1 This fifth edition cancels and replaces the fourth edition, published in 2003 and its amendment 1, published in 2007. This edition includes the following significant technical changes with respect to the previous edition: a) In Table 2 and Table 3 cooling methods IC01, IC11, IC21 and IC31, IC71, IC81 are now covered. b) This edition adds Table 3 for 60 Hz machines, whereas Table 2, which covers only 50 Hz machines, has no change in levels. c) In Table 3, grade A is added to harmonize the highest levels seen in IEC and NEMA, whereas grade B was added to harmonize the lowest, more restrictive levels seen in IEC and NEMA. d) The clause “Determination of noise increments caused by converter supply” has been shifted to Annex B and renamed “Information on typical noise increments caused by converter supply”.
Drehende elektrische Maschinen - Teil 9: Geräuschgrenzwerte
Machines électriques tournantes - Partie 9: Limites de bruit
IEC 60034-9:2021 spécifie les méthodes d’essai pour la détermination du niveau de puissance acoustique des machines électriques tournantes et spécifie les niveaux maximaux de puissance acoustique pondérée A pour les essais de réception en usine des machines électriques tournantes alimentées par réseau conformes à l’IEC 60034-1, dont les modes de refroidissement sont conformes à l’IEC 60034-6 et les degrés de protection conformes à l’IEC 60034-5, et qui présentent les caractéristiques suivantes: - conception normalisée, courant alternatif ou courant continu, sans modifications spéciales électriques, mécaniques ou acoustiques destinées à réduire le niveau de puissance acoustique - puissance assignée de 1 kW (ou kVA) jusqu'à 5 500 kW inclus (ou kVA) - vitesse assignée inférieure ou égale à 3 750 min–1 Cette cinquième édition annule et remplace la quatrième édition, parue en 2003 et son amendement 1, paru en 2007. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente: a) Le Tableau 2 et le Tableau 3 couvrent désormais les méthodes de refroidissement IC01, IC11, IC21 et IC31, IC71, IC81. b) La présente édition ajoute le Tableau 3 pour les machines de 60 Hz, tandis que le Tableau 2, qui ne couvre que les machines de 50 Hz, ne présente pas de modification de niveaux. c) Dans le Tableau 3, l’ajout du degré A vise à harmoniser les niveaux les plus élevés définis par l’IEC et NEMA, tandis que l’ajout du degré B visait à harmoniser les niveaux plus faibles mais plus restrictifs également définis par l’IEC et NEMA. d) L'article "Détermination de l’augmentation de bruit provoquée par l’alimentation du convertisseur" a été transféré dans l’Annexe B et renommé "Informations sur l’augmentation type de bruit provoquée par l’alimentation du convertisseur".
Električni rotacijski stroji - 9. del: Mejne vrednosti hrupa
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 60034-9:2021
01-april-2021
Električni rotacijski stroji - 9. del: Omejitve hrupa
Rotating electrical machines - Part 9: Noise limits
Drehende elektrische Maschinen - Teil 9: Geräuschgrenzwerte
Machines électriques tournantes - Partie 9: Limites de bruit
Ta slovenski standard je istoveten z: prEN IEC 60034-9:2021
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
29.160.01 Rotacijski stroji na splošno Rotating machinery in
general
oSIST prEN IEC 60034-9:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN IEC 60034-9:2021
oSIST prEN IEC 60034-9:2021
2/2034/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 60034-9 ED5
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2021-01-29 2021-04-23
SUPERSEDES DOCUMENTS:
2/1994/CD, 2/2022A/CC
IEC TC 2: ROTATING MACHINERY
SECRETARIAT: SECRETARY:
United Kingdom Mr Charles Whitlock
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if any, in
this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for Vote
(CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
TITLE:
Rotating electrical machines – Part 9: Noise limits
PROPOSED STABILITY DATE: 2024
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
oSIST prEN IEC 60034-9:2021
– 2 – IEC CDV 60034-9 IEC 2021
CONTENTS
CONTENTS . 2
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Methods of measurement . 9
5 Test conditions . 9
5.1 Machine mounting . 9
5.1.1 Precautions . 9
5.1.2 Resilient mounting . 9
5.1.3 Rigid mounting . 10
5.2 Test operating conditions . 10
6 Sound power level limits . 10
7 Determination of sound pressure level . 11
8 Declaration and verification of sound power values . 11
9 Bibliography . 12
Annex A (informative) – Levels of typical conversion values from power to pressure . 17
Annex B (informative) – Information on typical noise increments caused by converter
supply . 18
Table 1 – Maximum A-weighted sound power level, L in dB, at no-load (excluding
WA
motors according to Tables 2a and 2b) (Method of cooling, IC code, see IEC 60034-6)
(Method of protection, IP code, see IEC 60034-5) . 13
Table 2a – Maximum A-weighted sound power level, L in dB, at no-load, 50Hz,
WA
sinusoidal supply (for single speed three-phase cage induction motors) . 14
Table 2b – Maximum A-weighted sound power level, L in dB, at no-load, 60Hz,
WA
sinusoidal supply (for single speed three-phase cage induction motors) . 15
Table 3 –Expected increase, over no-load condition, in A-weighted sound power levels,
ΔL in dB, for rated load condition (for motors according to Table 2) . 16
WA
Table 4 – Typical values for measurement surface index for the conversion from sound
power to sound pressure based on using parallelepiped acc. to ISO 3744 . 17
oSIST prEN IEC 60034-9:2021
IEC CDV 60034-9 IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINES –
Part 9: Noise limits
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60034-9 has been prepared by IEC technical committee 2:
Rotating machinery.
Comment for CDV: The red font shows where the publication has been modified.
This fifth edition cancels and replaces the fourth edition 4.1 published in 2007 and all
amendments. This edition includes the following significant technical changes:
• In Tables 2 cooling methods IC01, IC11, IC21 and IC31, IC71, IC81 are now covered.
• This edition adds Table 2b for 60 Hz machines, whereas Table 2a, which covers only 50
Hz machines, has no change in levels.
• In Table 2b, grade A is added to harmonize the highest levels seen in IEC and NEMA,
whereas grade B was added to harmonize the lowest, more restrictive, levels seen in IEC
and NEMA.
oSIST prEN IEC 60034-9:2021
– 4 – IEC CDV 60034-9 IEC 2021
• The chapter “Determination of noise increments caused by converter supply” has been
shifted to Annex B and renamed to “Information on typical noise increments caused by
converter supply”
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the maintenance result date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date,
the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
oSIST prEN IEC 60034-9:2021
IEC CDV 60034-9 IEC 2021 – 5 –
1 INTRODUCTION
2 Acoustic quantities can be expressed in sound pressure terms or sound power terms. The use
3 of a sound power level, which can be specified independently of the measurement surface
4 and environmental conditions, avoids the complications associated with sound pressure
5 levels, which require additional data to be specified. Sound power levels provide a measure of
6 radiated energy and have advantages in acoustic analysis and design.
oSIST prEN IEC 60034-9:2021
– 6 – IEC CDV 60034-9 IEC 2021
9 ROTATING ELECTRICAL MACHINES –
11 Part 9: Noise limits
15 1 Scope
16 This part of IEC 60034:
17 – specifies test methods for the determination of sound power level of rotating electrical
18 machines;
19 – specifies maximum A-weighted sound power levels for factory acceptance testing of
20 network-supplied, rotating electrical machines in accordance with lEC 60034-1, having
21 methods of cooling according to lEC 60034-6 and degrees of protection according to
22 lEC 60034-5, and having the following characteristics:
23 • standard design, either a.c. or d.c., without additional special electrical, mechanical, or
24 acoustical modifications intended to reduce the sound power level;
25 • rated output from 1 kW (or kVA) up to and including 5 500 kW (or kVA);
–1
26 • rated speed not greater than 3 750 min .
27 Excluded are noise limits for a.c. motors supplied by converters. For these conditions see
28 Annex B for guidance.
29 The object of this standard is to determine maximum A-weighted sound power levels, L in
WA
30 decibels, dB, for airborne noise emitted by rotating electrical machines of standard design, as
31 a function of power, speed and load, and to specify the method of measurement and the test
32 conditions appropriate for the determination of the sound power level of the machines to
33 provide a standardized evaluation of machine noise up to the maximum specified sound
34 power levels. This standard does not provide correction for the existence of tonal
35 characteristics.
36 Sound pressure levels at a distance from the machine may be required in some applications,
37 such as hearing protection programs. Information is provided on such a procedure in Clause 7
38 based on a standardized test environment.
39 NOTE 1 This standard recognizes the economic reason for the availability of standard noise-level machines for
40 use in non-critical areas or for use with supplementary means of noise attenuation.
41 NOTE 2 Where sound power levels lower than those specified in Tables 1 or 2 are required, these should be
42 agreed between the manufacturer and the purchaser, as special electrical, mechanical, or acoustical design may
43 involve additional measures.
44 2 Normative references
45 The following referenced documents are indispensable for the application of this document.
46 For dated references, only the edition cited applies. For undated references, the latest edition
47 of the referenced document (including any amendments) applies.
48 IEC 60034-1, Rotating electrical machines – Part 1: Rating and performance
oSIST prEN IEC 60034-9:2021
IEC CDV 60034-9 IEC 2021 – 7 –
50 IEC 60034-5, Rotating electrical machines – Part 5: Degrees of protection provided by the
51 integral design of rotating electrical machines (IP code) – Classification
52 IEC 60034-6, Rotating electrical machines – Part 6: Methods of cooling (IC Code)
53 ISO 3741, Acoustics – Determination of sound power levels of noise sources using sound
54 pressure – Precision methods for reverberation rooms
55 ISO 3743-1, Acoustics – Determination of sound power l
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.