iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60512-17-3:2010

(Main)

Connectors for electronic equipment - Tests and measurements - Part 17-3: Cable clamping tests - Test 17c: Cable clamp resistance to cable pull (tensile)

Connectors for electronic equipment - Tests and measurements - Part 17-3: Cable clamping tests - Test 17c: Cable clamp resistance to cable pull (tensile)

IEC 60512-17-3:2010 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the ability of a cable-clamping device to prevent longitudinal movement of the cable/wire bundle.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 17-3: Prüfungen der Kabelabfangung - Prüfung 17c: Widerstandsfähigkeit der Kabelabfangung gegen axialen Zug

Connecteurs pour équipements électroniques - Essais et mesures - Partie 17-3: Essais de maintien des câbles - Essai 17c: Résistance de la pince de maintien des câbles au tirage

La CEI 60512-17-3:2010 est utilisée pour les essais des connecteurs du domaine d'activité du comité d'études 48, lorsque la spécification particulière l'exige. Elle peut également être utilisée pour des dispositifs similaires lorsqu'une spécification particulière le stipule. L'objet de cette norme document est de définir une méthode d'essai normalisée pour évaluer l'aptitude d'un dispositif de pincement de câbles à empêcher le mouvement longitudinal du faisceau de câbles/fils.

Konektorji za elektronsko opremo - Preskusi in meritve - 17-3. del: Preskušanje kabelskih objemk - Preskus 17c: Odpornost kabelskih objemk proti vlečenju (natezna) (IEC 60512-17-3:2010)

Ta del IEC 60512 se, kadar ga zahteva podrobna specifikacija, uporablja za preskušanje konektorjev v okviru tehničnega odbora 48. Lahko se uporablja tudi za podobne naprave, kadar ga določa podrobna specifikacija. Cilj tega standarda je podrobno opisati standardno preskusno metodo za ocenjevanje zmožnosti kabelske objemke, da preprečuje vzdolžno premikanje snopa kablov/žic.

General Information

Status
Published
Publication Date
09-Sep-2010
Withdrawal Date
31-Aug-2013
ICS
31.220.01 - Electromechanical components in general
Technical Committee
CLC/SR 48B - Connectors
Drafting Committee
IEC/SC 48B - IEC_SC_48B
Parallel Committee
IEC/SC 48B - IEC_SC_48B
Current Stage
6060 - Document made available - Publishing
Start Date
10-Sep-2010
Completion Date
10-Sep-2010
Ref Project
SIST EN 60512-17-3:2010 - Connectors for electronic equipment - Tests and measurements - Part 17-3: Cable clamping tests - Test 17c: Cable clamp resistance to cable pull (tensile) (IEC 60512-17-3:2010)

Buy Standard

EN 60512-17-3:2010EN 60512-17-3:2010
PreviousNext
Standard
EN 60512-17-3:2010
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60512-17-3:2010
01-december-2010
.RQHNWRUML]DHOHNWURQVNRRSUHPR3UHVNXVLLQPHULWYHGHO3UHVNXãDQMH
NDEHOVNLKREMHPN3UHVNXVF2GSRUQRVWNDEHOVNLKREMHPNSURWLYOHþHQMX
QDWH]QD  ,(&
Connectors for electronic equipment - Tests and measurements - Part 17-3: Cable
clamping tests - Test 17c: Cable clamp resistance to cable pull (tensile) (IEC 60512-17-
3:2010)
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 17-3:
Prüfungen der Kabelabfangung - Prüfung 17c: Widerstandsfähigkeit der Kabelabfangung
gegen axialen Zug (IEC 60512-17-3:2010)
Connecteurs pour équipements électroniques - Essais et mesures - Partie 17-3: Essais
de maintien des câbles - Essai 17c: Résistance de la pince de maintien des câbles au
tirage (CEI 60512-17-3:2010)
Ta slovenski standard je istoveten z: EN 60512-17-3:2010
ICS:
21.060.70 Sponke in skobe Clamps and staples
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60512-17-3:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60512-17-3:2010

---------------------- Page: 2 ----------------------

SIST EN 60512-17-3:2010

EUROPEAN STANDARD
EN 60512-17-3

NORME EUROPÉENNE
September 2010
EUROPÄISCHE NORM

ICS 31.220.01


English version


Connectors for electronic equipment -
Tests and measurements -
Part 17-3: Cable clamping tests -
Test 17c: Cable clamp resistance to cable pull (tensile)
(IEC 60512-17-3:2010)


Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Essais et mesures - Einrichtungen - Mess- und Prüfverfahren -
Partie 17-3: Essais de maintien Teil 17-3: Prüfungen der Kabelabfangung -
des câbles - Prüfung 17c: Widerstandsfähigkeit
Essai 17c: Résistance de la pince der Kabelabfangung gegen axialen Zug
de maintien des câbles au tirage (IEC 60512-17-3:2010)
(CEI 60512-17-3:2010)




This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-17-3:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60512-17-3:2010
EN 60512-17-3:2010 - 2 -
Foreword
The text of document 48B/2156/FDIS, future edition 1 of IEC 60512-17-3, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60512-17-3 on 2010-09-01
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60512-17-3:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60512-17-3:2010
- 3 - EN 60512-17-3:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following refer
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60512-9-5:2020(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 9-5: Endurance tests - Test 9e: Current loading, cyclic
SIST EN IEC 60512-9-5:2020

IEC 60512-9-5:2020 is available as IEC 60512-9-5:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60512-9-5:2020 when required by the detail product specification, is used for testing connectors or solderless connections within the scope of technical committee 48. It may also be used for similar devices when specified in a detail product specification. The object of this document is to detail a standard method for subjecting solderless connections to thermal stress conditioning by cyclic current loading. This second edition cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - added method B and renamed the former test method as method A, to provide an alternative with more adjustable time “ON” and “OFF” for products with larger thermal mass. - added introduction to provide background of this revision.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-11-1:2019(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 11-1: Climatic tests - Test 11a - Climatic sequence
SIST EN IEC 60512-11-1:2019

IEC 60512-11-1:2019 when required by the detail (product) specification, is used for testing connectors within the scope of IEC technical committee 48. This test may also be used for similar devices (i.e. when the degradation mechanisms are the same) when specified in a detail (product) specification. The object of this test is to define a standard test method to assess the ability of connectors to function in a specified manner, in a specified environment which might be encountered during normal use, including storage. This document provides a standard composite test method for determining the suitability of connectors when subjected to environmental conditions consisting of a sequence of temperature, humidity and, where required, low air pressure environmental stresses. Key words: Connectors, Climatic Tests

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-23-3:2019(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 23-3: Screening and filtering tests - Test 23c: Shielding effectiveness of connectors and accessories - Line injection method
SIST EN IEC 60512-23-3:2019

This part of IEC 60512 defines a standard test method for measuring the shielding effectiveness SE of a shielded connector, or of a connector not provided with integral shield once fitted with a shielding accessory and terminated with a screened cable. The complete assembly has a continuous 360° shielding capability throughout its length. NOTE 1 Practically, continuous 360° shielding is not always achievable based on the geometry of the connector. NOTE 2 Shielding" is used in this document with the same meaning as "screening". This test method can be applied to shielded connectors and to connector accessories with shielding capability. The following different connector designs can be tested: - circular connectors; - rectangular connectors; - connectors for printed boards; - connector shielding accessories. NOTE 3 For the definition of "accessory" see IEV 581-24-10. A shielding accessory i.e. an accessory that confers shielding to a non-inherently shielded connector, may be a suitable set of shielded housings providing electrical continuity, along the mated connector set, between the screen of the (screened) cable at the cable outlet of the free cable connector housing and the metallic mounting surface for the fixed connector housing. The free connector housing is provided with a cable screen clamp. This test method utilizes the principle that the intrinsic shielding property of the connector/accessory/cable assembly is its surface transfer impedance ZT which can be expressed as the longitudinal voltage inside the shield, relative to the current flow on the outside shell. This test method is based on two impedance-matched circuits. See Figure 1 for the measurement principle. The connector specimen under test is integrated into the secondary circuit 02. The impedance-matched injection line of the primary circuit 01, which activates the electromagnetic field, runs parallel to the surface of the specimen under test. This test is also suitable for measuring the shielding effectiveness of a connector fitted with triaxial contacts terminated with shielded, twisted pair cables, as used in data bus systems. NOTE 4 This standard has been adopted by ASD-STAN (formerly known as AECMA) as EN 2591-212.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-8-3:2018(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 8-3: Static load tests (fixed connectors) - Test 8c: Robustness of actuating lever
SIST EN IEC 60512-8-3:2018

IEC 60512-8-3:2018 this part of IEC 60512, when required by the detail (product) specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices, when specified in a detail (product) specification. The object of this document is to detail a standard test method to assess the robustness of the actuating lever of a connector mating or release mechanism. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: this edition reflects IEC 60512-1-101, Blank detail specification and Subclause 4.2 (Preparation of specimen) is improved.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-24-1:2012(Main)
Connectors for electronic equipment - Tests and measurements - Part 24-1: Magnetic interference tests - Test 24a: Residual magnetism
SIST EN 60512-24-1:2013

IEC 60512-24-1:2010 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard method to measure the residual magnetism of a connector after exposure to a specified magnetic field.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-9-2:2012(Main)
Connectors for electronic equipment - Tests and measurements - Part 9-2: Endurance tests - Test 9b: Electrical load and temperature
SIST EN 60512-9-2:2012

IEC 60512-9-2:2011 when required by the detail specification, this part of IEC 60512, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the ability of a connector to withstand elevated temperatures with electrical loading. This standard cancels and replaces Test 9b of IEC 60512-5, issued in 1992.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-7-2:2012(Main)
Connectors for electronic equipment - Tests and measurements - Part 7-2: Impact tests (free connectors) - Test 7b: Mechanical strength impact
SIST EN 60512-7-2:2012

IEC 60512-7-2:2011 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the ability of a free connector on the end of a cable or wire bundle to withstand impacts it could receive when dropped onto a hard surface.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-9-3:2011(Main)
Connectors for electronic equipment - Tests and measurements - Part 9-3: Endurance tests - Test 9c: Mechanical operation (engaging/separating) with electrical load
SIST EN 60512-9-3:2011

IEC 60512-9-3:2011 defines a standard test method to assess the mechanical and electrical operational endurance, i.e. engaging and separating cycles, of a connector in an operating mode which includes a specified electrical load. This second edition cancels and replaces Test 9c of IEC 60512-5, issued in 1992, and constitutes a technical revision. The main technical changes with regard to the previous edition are as follows: - An additional requirement to 4.1 stating that if more than one electrical circuit is wired for testing, the wiring shall be carried out in a parallel electrical circuit. - Subclauses 4.3 through 4.7 were removed and replaced by 4.2 through 4.4. This publication is to be read in conjunction with IEC 60512-1:2001 and IEC 60512-1-100:2006.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-17-2:2011(Main)
Connectors for electronic equipment - Tests and measurements - Part 17-2: Cable clamping tests - Test 17b: Cable clamp resistance to cable rotation
SIST EN 60512-17-2:2011

IEC 60512-17-2:2011 when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard method to assess the ability of a cable-clamping device to allow rotary movement of the cable/wire bundle without damage to the external surface of the cable/wire bundle, the cable-clamping device, the connector or the sub-assembly. This standard cancels and replaces Test 17b of IEC 60512-5, issued in 1992, and constitutes a technical revision. This publication is to be read in conjunction with  IEC 60512-1:2001 and IEC 60512-1-100:2006.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60512-8-2:2011(Main)
Connectors for electronic equipment - Tests and measurements - Part 8-2: Static load tests (fixed connectors) - Test 8b: Static load, axial
SIST EN 60512-8-2:2011

IEC 60512-8-2:2011 when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to determine the ability of a fixed connector to withstand a steady axial force which might occur during normal use. This standard cancels and replaces Test 8b of IEC 60512-5, issued in 1992, and constitutes a technical revision. This publication is to be read in conjunction with IEC 60512-1:2001 and IEC 60512-1-100:2006.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day