EN 60684-3-214:2005

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, shrink ratio 3:1 - Thick and medium wall

This standard gives the requirements for two types of heat-shrinkable, not flame retarded, polyolefin sleeving with a nominal shrink ratio of 3:1 and with thick and medium wall. This sleeving has been found suitable at temperatures up to 135 °C. - Type A: Medium wall - internal diameter of upt to 180,0 mm. - Type B: Thick wall - internal diameter of up to 160,0 mm.

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 214: Wärmeschrumpfende Polyolefinschläuche, nicht-flammwidrig, Schrumpfverhältnis 3:1 - Dickwandig und mittlere Wanddicke

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 214: Gaines thermorétractables en polyoléfine, non retardées à la flamme, rapport de rétreint 3:1 - Paroi moyenne et épaisse

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 214. list: Toplotno skrčljive poliolefinske cevi, ne ognjevarne, razmerje krčenja 3:1 - Debela in srednje debela stena (IEC 60684-3-214:2005)

General Information

• Status: Withdrawn
• Publication Date: 08-Dec-2005
• Withdrawal Date: 31-Oct-2008
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: CLC/SR 15 - Insulating materials
• Drafting Committee: IEC/TC 15 - IEC_TC_15
• Parallel Committee: IEC/SC 15C - IEC_SC_15C
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 24-Dec-2016
• Ref Project: SIST EN 60684-3-214:2008 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, shrink ratio 3:1 - Thick and medium wall

Relations

• Replaced By: EN 60684-3-214:2014 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, thick and medium wall
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2008
*LENHL]RODFLMVNHFHYLGHO6SHFLILNDFLMH]DSRVDPH]QHWLSHFHYLOLVW
7RSORWQRVNUþOMLYHSROLROHILQVNHFHYLQHRJQMHYDUQHUD]PHUMHNUþHQMD'HEHOD
LQVUHGQMHGHEHODVWHQD,(&
Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving --
Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, shrink ratio 3:1 -
Thick and medium wall
Isolierschläuche -- Teil 3: Anforderungen für einzelne Schlauchtypen -- Blatt 214:
Wärmeschrumpfende Polyolefinschläuche, nicht-flammwidrig, Schrumpfverhältnis 3:1 -
Dickwandig und mittlere Wanddicke
Gaines isolantes souples -- Partie 3: Spécifications pour types particuliers de gaines --
Feuille 214: Gaines thermorétractables en polyoléfine, non retardées à la flamme,
rapport de rétreint 3:1 - Paroi moyenne et épaisse
Ta slovenski standard je istoveten z: EN 60684-3-214:2005
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60684-3-214
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2005

ICS 29.035.20
English version
Flexible insulating sleeving
Part 3: Specifications for individual types of sleeving
Sheet 214: Heat-shrinkable, polyolefin sleeving,
not flame retarded, shrink ratio 3:1 -
Thick and medium wall
(IEC 60684-3-214:2005)
Gaines isolantes souples Isolierschläuche
Partie 3: Spécifications pour types Teil 3: Anforderungen für einzelne
particuliers de gaines Schlauchtypen
Feuille 214: Gaines thermorétractables Blatt 214: Wärmeschrumpfende
en polyoléfine, non retardées à la flamme, Polyolefinschläuche, nicht-flammwidrig,
rapport de rétreint 3:1 - Schrumpfverhältnis 3:1 -
Paroi moyenne et épaisse Dickwandig und mittlere Wanddicke
(CEI 60684-3-214:2005) (IEC 60684-3-214:2005)

This European Standard was approved by CENELEC on 2005-11-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60684-3-214:2005 E

Foreword
The text of document 15/230/FDIS, future edition 2 of IEC 60684-3-214, prepared by IEC TC 15,
Standards on specifications for electrical insulating materials, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 60684-3-214 on 2005-11-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-11-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60684-3-214:2005 was approved by CENELEC as a
European Standard without any modification.
__________
- 3 - EN 60684-3-214:2005
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60296 2003 Fluids for electrotechnical applications - EN 60296 2004
Unused mineral insulating oils for + corr. September 2004
transformers and switchgear
IEC 60684-1 2003 Flexible insulating sleeving EN 60684-1 2003
Part 1: Definitions and general
requirements
IEC 60684-2 1997 Part 2: Methods of test EN 60684-2 1997
A1 2003 A1 2003
IEC 60757 1983 Code for designation of colours HD 457 S1 1985

ISO 846 1997 Plastics - Evaluation of the action of EN ISO 846 1997
microorganisms
INTERNATIONAL IEC
STANDARD 60684-3-214
Second edition
2005-11
Flexible insulating sleeving –
Part 3:
Specifications for individual types of sleeving –
Sheet 214: Heat-shrinkable, polyolefin sleeving, not
flame retarded, shrink ratio 3:1 –
Thick and medium wall
 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale L
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – 60684-3-214  IEC:2005(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5

1 Scope.6
2 Normative references.6
3 Designation.7
4 Conditions of test.7
5 Requirements.7
6 Sleeving conformance.7

Table 1 – Dimensional and mass requirements – Type A .8
Table 2 – Dimensional and mass requirements – Type B .8
Table 3 – Property requirements .9
Table 4 – Requirements for breakdown voltage .10
Table 5 – Resistance to selected fluids .11
Table 6 – Additional property requirements.11

60684-3-214  IEC:2005(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 214: Heat-shrinkable, polyolefin sleeving,
not flame retarded, shrink ratio 3:1 – Thick and medium wall

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60684-3-214 has been prepared by IEC technical committee 15:
Standards on specifications for electrical Insulating materials.
This second edition replaces the first edition (2001) and constitutes a technical revision.
The main change with respect to the previous edition is as follows:
The thermal endurance test method according to IEC 60216 has been replaced with a long
term ageing test i.e. 3 000 h (see Amendment 1 to IEC 60684-2), at the recommended
maximum temperature found suitable for use, to provide safe thermal test data within a
workable time scale.
– 4 – 60684-3-214  IEC:2005(E)
The text of this standard is based on the following documents:
FDIS Report on voting
15/230/FDIS 15/248/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

60684-3-214  IEC:2005(E) – 5 –
INTRODUCTION
This International Standard is one of a series which deals with flexible insulating sleeving for
electrical purposes.
The series consists of three parts:
– Part 1: Definitions and general requirements (IEC 60684-1)
– Part 2: Methods of test (IEC 60684-2)
– Part 3: Specifications for individual types of sleeving (IEC 60684-3)
This standard comprises one of the sheets of Part 3 as follows:
Sheet 214: Heat-shrinkable, polyolefin sleeving, not flame retarded, shrink ratio 3:1 – Thick
and medium wall
– 6 – 60684-3-214  IEC:2005(E)
FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 214: Heat-shrinkable, polyolefin sleeving,
not flame retarded, shrink ratio 3:1 – Thick and medium wall

1 Scope
This standard gives the requirements for two types of heat-shrinkable, not flame retarded,
polyolefin sleeving with a nominal shrink ratio of 3:1 and with thick and medium wall. This
sleeving has been found suitable at temperatures up to 135 °C.
– Type A: Medium wall – internal diameter of up to 180,0 mm.
– Type B
...