ETSI EN 301 502 V12.1.1 (2015-03)
Global System for Mobile communications (GSM); Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive
Global System for Mobile communications (GSM); Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive
REN/MSG-0017
Globalni sistem mobilnih komunikacij (GSM) - Harmonizirani EN za opremo za bazne postaje, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
Ta dokument zajema določbe člena 3(2) Direktive 1999/5/ES [i.2] (direktive R&TTE), ki določa, da »[...] mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.«
Kar zadeva motnje sistemov, ki delujejo v sosednjih pasovih, so v Poročilo 146 Odbora za elektronske komunikacije [i.4] vključena navodila za enega ali več operaterjev baznih sprejemno-oddajnih postaj (BTS).
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE [i.2].
General Information
Standards Content (Sample)
Draft ETSI EN 301 502 V12.0.1 (2014-10)
Harmonized European Standard
Global System for Mobile communications (GSM);
Harmonized EN for Base Station Equipment covering the
essential requirements of article 3.2 of the R&TTE Directive
2 Draft ETSI EN 301 502 V12.0.1 (2014-10)
Reference
REN/MSG-0017
Keywords
base station, cellular, ER-GSM, GSM, R-GSM
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 301 502 V12.0.1 (2014-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 11
3 Definitions and abbreviations . 12
3.1 Definitions . 12
3.2 Abbreviations . 14
4 Technical requirements specifications . 16
4.1 Environmental profile . 16
4.2 Conformance requirements . 16
4.2.1 Void . 16
4.2.1a Introduction. 17
4.2.2 Mean transmitted RF carrier power . 17
4.2.2.1 Definition . 17
4.2.2.2 Limit . 17
4.2.2.3 Conformance . 18
4.2.3 Void . 18
4.2.4 Adjacent channel power . 18
4.2.4.1 Spectrum due to modulation and wideband noise . 18
4.2.4.1.1 Definition. 18
4.2.4.1.2 Limit . 18
4.2.4.1.3 Conformance . 20
4.2.4.2 Switching transients spectrum . 21
4.2.4.2.1 Definition. 21
4.2.4.2.2 Limit . 21
4.2.4.2.3 Conformance . 21
4.2.5 Spurious emissions from the transmitter antenna connector . 21
4.2.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 21
4.2.5.1.1 Definition. 21
4.2.5.1.2 Limit . 21
4.2.5.1.3 Conformance . 21
4.2.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 21
4.2.5.2.1 Definition. 22
4.2.5.2.2 Limit . 22
4.2.5.2.3 Conformance . 23
4.2.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 23
4.2.5.3.1 Definition. 23
4.2.5.3.2 Limit . 23
4.2.5.3.3 Conformance . 23
4.2.6 Intermodulation attenuation . 23
4.2.6.1 Definition . 23
4.2.6.2 Limit . 23
4.2.6.2.1 For BTS not belonging to a multicarrier BTS class . 23
4.2.6.2.2 For BTS belonging to a multicarrier BTS class . 24
4.2.6.3 Conformance . 24
4.2.7 Intra Base Station System intermodulation attenuation . 24
ETSI
4 Draft ETSI EN 301 502 V12.0.1 (2014-10)
4.2.7.1 Definition . 24
4.2.7.2 Limit . 25
4.2.7.2.1 For BTS not belonging to a multicarrier BTS class . 25
4.2.7.2.2 For BTS belonging to a multicarrier BTS class . 25
4.2.7.3 Conformance . 25
4.2.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 25
4.2.8.1 Definition . 25
4.2.8.2 Limit . 25
4.2.9 Void . 27
4.2.10 Void . 27
4.2.11 Reference Interference Level . 27
4.2.11.1 Definition . 27
4.2.11.2 Limit . 27
4.2.11.3 Conformance . 33
4.2.12 Blocking Characteristics . 33
4.2.12.1 Definition . 34
4.2.12.2 Limit . 34
4.2.12.2.1 Blocking . 34
4.2.12.2.2 Spurious response . 35
4.2.12.3 Conformance . 35
4.2.13 Intermodulation characteristics . 35
4.2.13.1 Definition . 35
4.2.13.2 Limit . 35
4.2.13.3 Conformance . 35
4.2.14 AM suppression . 35
4.2.14.1 Definition . 35
4.2.14.2 Limit . 35
4.2.14.3 Conformance . 36
4.2.15 Spurious emissions from the receiver antenna connector . 36
4.2.15.1 Definition . 36
4.2.15.2 Limit . 36
4.2.15.3 Conformance . 36
4.2.16 Radiated spurious emissions . 36
4.2.16.1 Definition . 36
4.2.16.2 Limit . 36
4.2.16.3 Conformance . 36
5 Testing for compliance with technical requirements . 37
5.1 Environmental conditions for testing . 37
5.2 Interpretation of the measurement results . 37
5.3 Essential radio test suites . 38
5.3.1 Void . 38
5.3.2 Mean transmitted RF carrier power . 38
5.3.2.1 Test case . 38
5.3.2.2 Test Environment . 39
5.3.3 Void . 39
5.3.4 Adjacent channel power . 39
5.3.4.1 Spectrum due to modulation and wideband noise . 39
5.3.4.1.1 Test case . 39
5.3.4.1.2 Test Environment . 40
5.3.4.2 Switching transients spectrum . 40
5.3.4.2.1 Test case . 40
5.3.4.2.2 Test Environment . 41
5.3.5 Spurious emissions from the transmitter antenna connector . 41
5.3.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 41
5.3.5.1.1 Test case . 41
5.3.5.1.2 Test Environment . 42
5.3.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 42
5.3.5.2.1 For BTS not belonging to a multicarrier BTS class . 42
5.3.5.2.2 For BTS belonging to a multicarrier BTS class . 43
ETSI
5 Draft ETSI EN 301 502 V12.0.1 (2014-10)
5.3.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 45
5.3.5.3.1 Test case . 45
5.3.5.3.2 Test Environment . 46
5.3.6 Intermodulation attenuation . 46
5.3.6.1 Test case . 46
5.3.6.2 Test Environment . 47
5.3.7 Intra Base Station System intermodulation attenuation . 48
5.3.7.1 Test case . 48
5.3.7.2 Test Environment . 49
5.3.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 49
5.3.8.1 Test case . 49
5.3.8.2 Test Environment . 51
5.3.9 Void . 51
5.3.10 Void . 51
5.3.11 Reference Interference Level . 51
5.3.11.1 Test case . 51
5.3.11.2 Test Environment . 59
5.3.12 Blocking Characteristics . 59
5.3.12.1 Test case . 59
5.3.12.2 Test Environment . 65
5.3.13 Intermodulation characteristics . 65
5.3.13.1 Test case . 65
5.3.13.2 Test Environment . 66
5.3.14 AM suppression . 66
5.3.14.1 Test case . 66
5.3.14.2 Test Environment . 68
5.3.15 Spurious emissions from the receiver antenna connector . 68
5.3.15.1 Test case . 68
5.3.15.2 Test Environment . 68
5.3.16 Radiated spurious emissions . 69
5.3.16.1 Test case . 70
5.3.16.2 Test Environment . 71
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 72
Annex B (normative): General test conditions and declarations . 74
B.1 Declaration by manufacturer . 74
B.1.1 Output power and determination of power class . 74
B.1.2 Specified frequency range . 75
B.1.3 Frequency hopping . 75
B.1.4 Void . 75
B.1.5 Downlink discontinuous transmission (DTX) . 75
B.2 BTS Configurations . 76
B.2.1 Receiver diversity . 76
B.2.2 Duplexers . 76
B.2.3 Power supply options . 77
B.2.4 Ancillary RF amplifiers . 77
B.2.5 BSS using antenna arrays . 78
B.2.6 BTS supporting 8-PSK modulation . 79
B.2.7 BTS supporting additional modulations in EGPRS2 . 79
B.2.8 Supported Symbol Rate . 79
B.2.9 Support of RTTI and/or FANR . 79
B.2.10 Multicarrier BTS . 80
B.2.11 BTS supporting VAMOS . 81
B.2.12 BTS supporting ER-GSM . 81
Annex C (normative): Test environments . 82
C.1 Normal test environment . 82
ETSI
6 Draft ETSI EN 301 502 V12.0.1 (2014-10)
C.2 Extreme test environment . 82
C.2.1 Extreme temperature . 83
C.3 Void . 83
C.4 Power supply . 83
Annex D: Void . 84
Annex E (informative): Bibliography . 85
History . 86
ETSI
7 Draft ETSI EN 301 502 V12.0.1 (2014-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards
Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The update to version 12.1.1 of the present document includes the following major changes:
• Inclusion of BTS equipment supporting operation in the ER-GSM 900 band.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.5].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
8 Draft ETSI EN 301 502 V12.0.1 (2014-10)
1 Scope
The present document applies to the following radio equipment type:
1) GSM base stations.
Table 1-1: GSM Base Station System frequency bands
GSM band Direction of GSM Base Station System relevant frequency bands
transmission
P-GSM 900 Transmit 935 MHz to 960 MHz
Receive 890 MHz to 915 MHz
E-GSM 900 Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
R-GSM 900 Transmit 921 MHz to 960 MHz
Receive 876 MHz to 915 MHz
ER-GSM 900 Transmit 918 MHz to 960 MHz
Receive 873 MHz to 915 MHz
DCS 1 800 Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
GSM 450 Transmit 460,4 MHz to 467,6 MHz
Receive 450,4 MHz to 457,6 MHz
GSM 480 Transmit 488,8 MHz to 496 MHz
Receive 478,8 MHz to 486 MHz
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In regards to interference to systems operating in adjacent bands guidance for single carrier BTS and multicarrier BTS
is provided in ECC Report 146 [i.4].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI TR 121 905 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; Vocabulary for 3GPP
Specifications (3GPP TR 21.905 version 12.0.0 Release 12)".
ETSI
9 Draft ETSI EN 301 502 V12.0.1 (2014-10)
[2] ETSI TS 151 021 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Base Station System (BSS) equipment specification; Radio aspects (3GPP TS 51.021
version 12.2.0 Release 12)".
[3] ETSI TS 145 002 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Multiplexing and multiple access on the radio path (3GPP TS 45.002 version 12.2.0 Release 12)".
[4] ETSI TS 145 004 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Modulation (3GPP TS 45.004 version 12.0.0 Release 12)".
[5] ETSI TS 145 005 (V12.3.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Radio Transmission and reception (3GPP TS 45.005 version 12.3.0 Release 12)".
[6] Void.
[7] ETSI TS 145 010 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Radio subsystem synchronization (3GPP TS 45.010 version 12.0.0 Release 12)".
[8] Void.
[9] Void.
[10] ETSI EN 300 019-1-0 (V2.1.2) (09-2003): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of
environmental conditions; Introduction".
[11] ETSI EN 300 019-1-3 (V2.4.1) (04-2014): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of
environmental conditions; Stationary use at weatherprotected locations".
[12] ETSI EN 300 019-1-4 (V2.2.1) (04-2014): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-4: Classification of
environmental conditions; Stationary use at non-weatherprotected locations".
[13] Void.
[14] Void.
[15] ETSI TS 124 022 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); Radio Link Protocol (RLP) for circuit
switched bearer and teleservices (3GPP TS 24.022 version 12.0.0 Release 12)".
[16] ETSI TS 148 020 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Rate adaption on the Base Station System - Mobile-services Switching Centre (BSS-MSC)
interface (3GPP TS 48.020 version 12.0.0 Release 12)".
[17] Recommendation ITU-T O.153 (10-1992): "Basic Parameters for the measurement of error
performance at bit rates below the primary rate".
[18] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain".
[19] Void.
[20] Void.
[21] Void.
[22] ETSI EN 300 019-2-3 (V2.3.1) (04-2013): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 2-3: Specification of
environmental tests; Stationary use at weatherprotected locations".
[23] ETSI EN 300 019-2-4 (V2.3.1) (08-2013): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of
environmental tests; Stationary use at non-weatherprotected locations".
ETSI
10 Draft ETSI EN 301 502 V12.0.1 (2014-10)
[24] IEC EN 60721-1 (ed.2.2, 10-2002): "Classification of environmental conditions:
Part 1: Environmental parameters and their severities".
[25] IEC EN 60721-2-1 (ed.2.0, 06-2013): "Classification of environmental conditions -
Part 2-1: Environmental conditions appearing in nature - Temperature and humidity".
[26] IEC EN 60721-2-4 (ed.1.1, 10-2002): "Classification of environmental conditions -
Part 2-4: Environmental conditions appearing in nature - Solar radiation and temperature".
[27] IEC EN 60721-3-0 (ed.1.1, 10-2002): "Classification of environmental conditions -
Part 3: Classification of groups of environmental parameters and their severities - Introduction".
[28] ETSI EN 301 908-1 (V6.2.1) (04-2013): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common
requirements".
[29] ETSI EN 301 908-18 (V7.1.0) (04-2014): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 18: E-UTRA, UTRA and
GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)".
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of Harmonized Standards for application under the R&TTE Directive".
[i.4] ECC Report 146: "Compatibility between GSM MCBTS and other services (TRR, RSBN/PRMG,
HC-SDMA, GSM-R, DME, MIDS, DECT) operating in the 900 and 1800 MHz frequency bands",
6th July 2010.
[i.5] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
[i.6] ETSI TS 144 060 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station System (BSS)
interface; Radio Link Control / Medium Access Control (RLC/MAC) protocol (3GPP TS 44.060
version 12.2.0 Release 12)".
[i.7] CEPT/ERC/Recommendation 74-01E (01-2011): "Unwanted emissions in the spurious domain".
[i.8] ETSI TR 100 028 (all parts) (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
[i.9] ETSI TS 145 001 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Physical layer on the radio path; General description (3GPP TS 45.001 version 12.0.0
Release 12)".
[i.10] ETSI TR 145 050 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Background for Radio Frequency (RF) requirements (3GPP TR 45.050 version 12.0.0
Release 12)".
ETSI
11 Draft ETSI EN 301 502 V12.0.1 (2014-10)
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in TR 121 905 [1] and the following apply:
8-PSK: Modulation type as defined in TS 145 004 [4], clause 3.
16-QAM: Modulation type as defined in TS 145 004 [4], clause 4 for EGPRS2-A and clause 5 for EGRPS2-B.
32-QAM: Modulation type as defined in TS 145 004 [4], clause 4 for EGPRS2-A and clause 5 for EGRPS2-B.
ancillary RF amplifier: piece of equipment, which when connected by RF coaxial cables to the BTS, has the primary
function to provide amplification between the transmit and/or receive antenna connector of a BTS and an antenna
without requiring any control signal to fulfil its amplifying function
AQPSK: Modulation type as defined in TS 145 004 [4], clause 6.
base station RF bandwidth: instantaneous bandwidth in which a BTS belonging to a multicarrier BTS class transmits
or transmits and receives multiple carriers simultaneously
Base Station System Test Equipment (BSSTE): See annex B in TS 151 021 [2].
BSS: BTS or integrated BSS
NOTE: If a separate BSC is required to perform tests on a BTS, the BSC may be regarded as test equipment and
the environmental conditions of the BSC need not be controlled.
carrier frequency: centre of the ARFCN under test
circuit switched logical channels: all the standard GSM logical channels, including traffic channels (TCH), common
control channels (RACH) and dedicated control channels (SDCCH, SACCH)
E-GSM: extended GSM 900 band (includes P-GSM band)
ECSD: any subset of the E-TCH traffic channels and related control channels
EGPRS: any subset of the packet traffic channels PDTCH/MCS-1 to MCS-9 and related control channels
EGPRS2: any of EGPRS2-A and EGPRS2-B
EGPRS2-A: packet traffic channels utilizing any subset of the packet traffic channels MCS-1 to 6 and PDTCH/UAS-7
to UAS-11 in uplink, together with MCS-1 to 4 a
...
HARMONIZED EUROPEAN STANDARD
Global System for Mobile communications (GSM);
Harmonized EN for Base Station Equipment covering the
essential requirements of article 3.2 of the R&TTE Directive
2 ETSI EN 301 502 V12.1.1 (2015-03)
Reference
REN/MSG-0017
Keywords
base station, cellular, ER-GSM, GSM, R-GSM
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 502 V12.1.1 (2015-03)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 10
3 Definitions and abbreviations . 11
3.1 Definitions . 11
3.2 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental profile . 14
4.2 Conformance requirements . 15
4.2.1 Void . 15
4.2.1a Introduction. 16
4.2.2 Mean transmitted RF carrier power . 16
4.2.2.1 Definition . 16
4.2.2.2 Limit . 16
4.2.2.3 Conformance . 17
4.2.3 Void . 17
4.2.4 Adjacent channel power . 17
4.2.4.1 Spectrum due to modulation and wideband noise . 17
4.2.4.1.1 Definition. 17
4.2.4.1.2 Limit . 17
4.2.4.1.3 Conformance . 19
4.2.4.2 Switching transients spectrum . 19
4.2.4.2.1 Definition. 19
4.2.4.2.2 Limit . 19
4.2.4.2.3 Conformance . 20
4.2.5 Spurious emissions from the transmitter antenna connector . 20
4.2.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 20
4.2.5.1.1 Definition. 20
4.2.5.1.2 Limit . 20
4.2.5.1.3 Conformance . 20
4.2.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 20
4.2.5.2.1 Definition. 20
4.2.5.2.2 Limit . 20
4.2.5.2.3 Conformance . 21
4.2.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 22
4.2.5.3.1 Definition. 22
4.2.5.3.2 Limit . 22
4.2.5.3.3 Conformance . 22
4.2.6 Intermodulation attenuation . 22
4.2.6.1 Definition . 22
4.2.6.2 Limit . 22
4.2.6.2.1 For BTS not belonging to a multicarrier BTS class . 22
4.2.6.2.2 For BTS belonging to a multicarrier BTS class . 22
4.2.6.3 Conformance . 23
4.2.7 Intra Base Station System intermodulation attenuation . 23
4.2.7.1 Definition . 23
ETSI
4 ETSI EN 301 502 V12.1.1 (2015-03)
4.2.7.2 Limit . 23
4.2.7.2.1 For BTS not belonging to a multicarrier BTS class . 23
4.2.7.2.2 For BTS belonging to a multicarrier BTS class . 23
4.2.7.3 Conformance . 23
4.2.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 24
4.2.8.1 Definition . 24
4.2.8.2 Limit . 24
4.2.9 Void . 25
4.2.10 Void . 25
4.2.11 Reference Interference Level . 26
4.2.11.1 Definition . 26
4.2.11.2 Limit . 26
4.2.11.3 Conformance . 32
4.2.12 Blocking Characteristics . 32
4.2.12.1 Definition . 32
4.2.12.2 Limit . 33
4.2.12.2.1 Blocking . 33
4.2.12.2.2 Spurious response . 33
4.2.12.3 Conformance . 34
4.2.13 Intermodulation characteristics . 34
4.2.13.1 Definition . 34
4.2.13.2 Limit . 34
4.2.13.3 Conformance . 34
4.2.14 AM suppression . 34
4.2.14.1 Definition . 34
4.2.14.2 Limit . 34
4.2.14.3 Conformance . 34
4.2.15 Spurious emissions from the receiver antenna connector . 34
4.2.15.1 Definition . 34
4.2.15.2 Limit . 35
4.2.15.3 Conformance . 35
4.2.16 Radiated spurious emissions . 35
4.2.16.1 Definition . 35
4.2.16.2 Limit . 35
4.2.16.3 Conformance . 35
5 Testing for compliance with technical requirements . 35
5.1 Environmental conditions for testing . 35
5.2 Interpretation of the measurement results . 36
5.3 Essential radio test suites . 37
5.3.1 Void . 37
5.3.2 Mean transmitted RF carrier power . 37
5.3.2.1 Test case . 37
5.3.2.2 Test Environment . 38
5.3.3 Void . 38
5.3.4 Adjacent channel power . 38
5.3.4.1 Spectrum due to modulation and wideband noise . 38
5.3.4.1.1 Test case . 38
5.3.4.1.2 Test Environment . 39
5.3.4.2 Switching transients spectrum . 39
5.3.4.2.1 Test case . 39
5.3.4.2.2 Test Environment . 40
5.3.5 Spurious emissions from the transmitter antenna connector . 40
5.3.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 40
5.3.5.1.1 Test case . 40
5.3.5.1.2 Test Environment . 40
5.3.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 41
5.3.5.2.1 For BTS not belonging to a multicarrier BTS class . 41
5.3.5.2.2 For BTS belonging to a multicarrier BTS class . 42
ETSI
5 ETSI EN 301 502 V12.1.1 (2015-03)
5.3.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 43
5.3.5.3.1 Test case . 44
5.3.5.3.2 Test Environment . 44
5.3.6 Intermodulation attenuation . 44
5.3.6.1 Test case . 44
5.3.6.2 Test Environment . 46
5.3.7 Intra Base Station System intermodulation attenuation . 46
5.3.7.1 Test case . 46
5.3.7.2 Test Environment . 47
5.3.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 47
5.3.8.1 Test case . 47
5.3.8.2 Test Environment . 49
5.3.9 Void . 50
5.3.10 Void . 50
5.3.11 Reference Interference Level . 50
5.3.11.1 Test case . 50
5.3.11.2 Test Environment . 58
5.3.12 Blocking Characteristics . 58
5.3.12.1 Test case . 58
5.3.12.2 Test Environment . 64
5.3.13 Intermodulation characteristics . 64
5.3.13.1 Test case . 64
5.3.13.2 Test Environment . 65
5.3.14 AM suppression . 65
5.3.14.1 Test case . 65
5.3.14.2 Test Environment . 67
5.3.15 Spurious emissions from the receiver antenna connector . 67
5.3.15.1 Test case . 67
5.3.15.2 Test Environment . 67
5.3.16 Radiated spurious emissions . 68
5.3.16.1 Test case . 69
5.3.16.2 Test Environment . 70
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 71
Annex B (normative): General test conditions and declarations . 73
B.1 Declaration by manufacturer . 73
B.1.1 Output power and determination of power class . 73
B.1.2 Specified frequency range . 74
B.1.3 Frequency hopping . 74
B.1.4 Void . 74
B.1.5 Downlink discontinuous transmission (DTX) . 74
B.2 BTS Configurations . 74
B.2.1 Receiver diversity . 75
B.2.2 Duplexers . 75
B.2.3 Power supply options . 76
B.2.4 Ancillary RF amplifiers . 76
B.2.5 BSS using antenna arrays . 76
B.2.6 BTS supporting 8-PSK modulation . 78
B.2.7 BTS supporting additional modulations in EGPRS2 . 78
B.2.8 Supported Symbol Rate . 78
B.2.9 Support of RTTI and/or FANR . 78
B.2.10 Multicarrier BTS . 78
B.2.11 BTS supporting VAMOS . 79
B.2.12 BTS supporting ER-GSM . 80
Annex C (normative): Test environments . 81
C.1 Normal test environment . 81
ETSI
6 ETSI EN 301 502 V12.1.1 (2015-03)
C.2 Extreme test environment . 81
C.2.1 Extreme temperature . 81
C.3 Void . 82
C.4 Power supply . 82
Annex D: Void . 83
Annex E (informative): Bibliography . 84
History . 85
ETSI
7 ETSI EN 301 502 V12.1.1 (2015-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The update to version 12.1.1 of the present document includes the following major changes:
• Inclusion of BTS equipment supporting operation in the ER-GSM 900 band.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.5].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
National transposition dates
Date of adoption of this EN: 24 February 2015
Date of latest announcement of this EN (doa): 31 May 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2015
Date of withdrawal of any conflicting National Standard (dow): 30 November 2016
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
8 ETSI EN 301 502 V12.1.1 (2015-03)
1 Scope
The present document applies to the following radio equipment type:
1) GSM base stations.
Table 1-1: GSM Base Station System frequency bands
GSM band Direction of GSM Base Station System relevant frequency bands
transmission
P-GSM 900 Transmit 935 MHz to 960 MHz
Receive 890 MHz to 915 MHz
E-GSM 900 Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
R-GSM 900 Transmit 921 MHz to 960 MHz
Receive 876 MHz to 915 MHz
ER-GSM 900 Transmit 918 MHz to 960 MHz
Receive 873 MHz to 915 MHz
DCS 1 800 Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
GSM 450 Transmit 460,4 MHz to 467,6 MHz
Receive 450,4 MHz to 457,6 MHz
GSM 480 Transmit 488,8 MHz to 496 MHz
Receive 478,8 MHz to 486 MHz
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In regards to interference to systems operating in adjacent bands guidance for single carrier BTS and multicarrier BTS
is provided in ECC Report 146 [i.4].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TR 121 905 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); LTE; Vocabulary for 3GPP
Specifications (3GPP TR 21.905 version 12.0.0 Release 12)".
[2] ETSI TS 151 021 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Base Station System (BSS) equipment specification; Radio aspects (3GPP TS 51.021
version 12.2.0 Release 12)".
ETSI
9 ETSI EN 301 502 V12.1.1 (2015-03)
[3] ETSI TS 145 002 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Multiplexing and multiple access on the radio path (3GPP TS 45.002 version 12.2.0 Release 12)".
[4] ETSI TS 145 004 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Modulation (3GPP TS 45.004 version 12.0.0 Release 12)".
[5] ETSI TS 145 005 (V12.3.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Radio Transmission and reception (3GPP TS 45.005 version 12.3.0 Release 12)".
[6] Void.
[7] ETSI TS 145 010 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Radio subsystem synchronization (3GPP TS 45.010 version 12.0.0 Release 12)".
[8] Void.
[9] Void.
[10] ETSI EN 300 019-1-0 (V2.1.2) (09-2003): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of
environmental conditions; Introduction".
[11] ETSI EN 300 019-1-3 (V2.4.1) (04-2014): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of
environmental conditions; Stationary use at weatherprotected locations".
[12] ETSI EN 300 019-1-4 (V2.2.1) (04-2014): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-4: Classification of
environmental conditions; Stationary use at non-weatherprotected locations".
[13] Void.
[14] Void.
[15] ETSI TS 124 022 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Universal Mobile Telecommunications System (UMTS); Radio Link Protocol (RLP) for circuit
switched bearer and teleservices (3GPP TS 24.022 version 12.0.0 Release 12)".
[16] ETSI TS 148 020 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Rate adaption on the Base Station System - Mobile-services Switching Centre (BSS-MSC)
interface (3GPP TS 48.020 version 12.0.0 Release 12)".
[17] Recommendation ITU-T O.153 (10-1992): "Basic Parameters for the measurement of error
performance at bit rates below the primary rate".
[18] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain".
[19] Void.
[20] Void.
[21] Void.
[22] ETSI EN 300 019-2-3 (V2.3.1) (04-2013): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 2-3: Specification of
environmental tests; Stationary use at weatherprotected locations".
[23] ETSI EN 300 019-2-4 (V2.3.1) (08-2013): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of
environmental tests; Stationary use at non-weatherprotected locations".
[24] IEC EN 60721-1 (ed.2.2, 10-2002): "Classification of environmental conditions:
Part 1: Environmental parameters and their severities".
[25] IEC EN 60721-2-1 (ed.2.0, 06-2013): "Classification of environmental conditions -
Part 2-1: Environmental conditions appearing in nature - Temperature and humidity".
ETSI
10 ETSI EN 301 502 V12.1.1 (2015-03)
[26] IEC EN 60721-2-4 (ed.1.1, 10-2002): "Classification of environmental conditions -
Part 2-4: Environmental conditions appearing in nature - Solar radiation and temperature".
[27] IEC EN 60721-3-0 (ed.1.1, 10-2002): "Classification of environmental conditions -
Part 3: Classification of groups of environmental parameters and their severities - Introduction".
[28] ETSI EN 301 908-1 (V6.2.1) (04-2013): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common
requirements".
[29] ETSI EN 301 908-18 (V7.1.2) (07-2014): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 18: E-UTRA, UTRA and
GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of Harmonized Standards for application under the R&TTE Directive".
[i.4] ECC Report 146: "Compatibility between GSM MCBTS and other services (TRR, RSBN/PRMG,
HC-SDMA, GSM-R, DME, MIDS, DECT) operating in the 900 and 1800 MHz frequency bands",
6th July 2010.
[i.5] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
[i.6] ETSI TS 144 060 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station System (BSS)
interface; Radio Link Control / Medium Access Control (RLC/MAC) protocol (3GPP TS 44.060
version 12.2.0 Release 12)".
[i.7] CEPT/ERC/Recommendation 74-01E (01-2011): "Unwanted emissions in the spurious domain".
[i.8] ETSI TR 100 028 (all parts) (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
[i.9] ETSI TS 145 001 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Physical layer on the radio path; General description (3GPP TS 45.001 version 12.0.0
Release 12)".
[i.10] ETSI TR 145 050 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+);
Background for Radio Frequency (RF) requirements (3GPP TR 45.050 version 12.0.0
Release 12)".
ETSI
11 ETSI EN 301 502 V12.1.1 (2015-03)
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in TR 121 905 [1] and the following apply:
8-PSK: Modulation type as defined in TS 145 004 [4], clause 3.
16-QAM: Modulation type as defined in TS 145 004 [4], clause 4 for EGPRS2-A and clause 5 for EGRPS2-B.
32-QAM: Modulation type as defined in TS 145 004 [4], clause 4 for EGPRS2-A and clause 5 for EGRPS2-B.
ancillary RF amplifier: piece of equipment, which when connected by RF coaxial cables to the BTS, has the primary
function to provide amplification between the transmit and/or receive antenna connector of a BTS and an antenna
without requiring any control signal to fulfil its amplifying function
AQPSK: Modulation type as defined in TS 145 004 [4], clause 6.
base station RF bandwidth: instantaneous bandwidth in which a BTS belonging to a multicarrier BTS class transmits
or transmits and receives multiple carriers simultaneously
Base Station System Test Equipment (BSSTE): See annex B in TS 151 021 [2].
BSS: BTS or integrated BSS
NOTE: If a separate BSC is required to perform tests on a BTS, the BSC may be regarded as test equipment and
the environmental conditions of the BSC need not be controlled.
carrier frequency: centre of the ARFCN under test
circuit switched logical channels: all the standard GSM logical channels, including traffic channels (TCH), common
control channels (RACH) and dedicated control channels (SDCCH, SACCH)
E-GSM: extended GSM 900 band (includes P-GSM band)
ECSD: any subset of the E-TCH traffic channels and related control channels
EGPRS: any subset of t
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.7(Global System for Mobile communications (GSM) - Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive33.070.50Globalni sistem za mobilno telekomunikacijo (GSM)Global System for Mobile Communication (GSM)ICS:Ta slovenski standard je istoveten z:EN 301 502 V12.1.1SIST EN 301 502 V12.1.1:2015en01-oktober-2015SIST EN 301 502 V12.1.1:2015SLOVENSKI
STANDARD
HARMONIZED EUROPEAN STANDARD SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 2
Reference REN/MSG-0017 Keywords base station, cellular, ER-GSM, GSM, R-GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 10 3 Definitions and abbreviations . 11 3.1 Definitions . 11 3.2 Abbreviations . 13 4 Technical requirements specifications . 14 4.1 Environmental profile . 14 4.2 Conformance requirements . 15 4.2.1 Void . 15 4.2.1a Introduction. 16 4.2.2 Mean transmitted RF carrier power . 16 4.2.2.1 Definition . 16 4.2.2.2 Limit . 16 4.2.2.3 Conformance . 17 4.2.3 Void . 17 4.2.4 Adjacent channel power . 17 4.2.4.1 Spectrum due to modulation and wideband noise . 17 4.2.4.1.1 Definition. 17 4.2.4.1.2 Limit . 17 4.2.4.1.3 Conformance . 19 4.2.4.2 Switching transients spectrum . 19 4.2.4.2.1 Definition. 19 4.2.4.2.2 Limit . 19 4.2.4.2.3 Conformance . 20 4.2.5 Spurious emissions from the transmitter antenna connector . 20 4.2.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit band . 20 4.2.5.1.1 Definition. 20 4.2.5.1.2 Limit . 20 4.2.5.1.3 Conformance . 20 4.2.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit band . 20 4.2.5.2.1 Definition. 20 4.2.5.2.2 Limit . 20 4.2.5.2.3 Conformance . 21 4.2.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the BTS transmit band . 22 4.2.5.3.1 Definition. 22 4.2.5.3.2 Limit . 22 4.2.5.3.3 Conformance . 22 4.2.6 Intermodulation attenuation . 22 4.2.6.1 Definition . 22 4.2.6.2 Limit . 22 4.2.6.2.1 For BTS not belonging to a multicarrier BTS class . 22 4.2.6.2.2 For BTS belonging to a multicarrier BTS class . 22 4.2.6.3 Conformance . 23 4.2.7 Intra Base Station System intermodulation attenuation . 23 4.2.7.1 Definition . 23 SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 4 4.2.7.2 Limit . 23 4.2.7.2.1 For BTS not belonging to a multicarrier BTS class . 23 4.2.7.2.2 For BTS belonging to a multicarrier BTS class . 23 4.2.7.3 Conformance . 23 4.2.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 24 4.2.8.1 Definition . 24 4.2.8.2 Limit . 24 4.2.9 Void . 25 4.2.10 Void . 25 4.2.11 Reference Interference Level . 26 4.2.11.1 Definition . 26 4.2.11.2 Limit . 26 4.2.11.3 Conformance . 32 4.2.12 Blocking Characteristics . 32 4.2.12.1 Definition . 32 4.2.12.2 Limit . 33 4.2.12.2.1 Blocking . 33 4.2.12.2.2 Spurious response . 33 4.2.12.3 Conformance . 34 4.2.13 Intermodulation characteristics . 34 4.2.13.1 Definition . 34 4.2.13.2 Limit . 34 4.2.13.3 Conformance . 34 4.2.14 AM suppression . 34 4.2.14.1 Definition . 34 4.2.14.2 Limit . 34 4.2.14.3 Conformance . 34 4.2.15 Spurious emissions from the receiver antenna connector . 34 4.2.15.1 Definition . 34 4.2.15.2 Limit . 35 4.2.15.3 Conformance . 35 4.2.16 Radiated spurious emissions . 35 4.2.16.1 Definition . 35 4.2.16.2 Limit . 35 4.2.16.3 Conformance . 35 5 Testing for compliance with technical requirements . 35 5.1 Environmental conditions for testing . 35 5.2 Interpretation of the measurement results . 36 5.3 Essential radio test suites . 37 5.3.1 Void . 37 5.3.2 Mean transmitted RF carrier power . 37 5.3.2.1 Test case . 37 5.3.2.2 Test Environment . 38 5.3.3 Void . 38 5.3.4 Adjacent channel power . 38 5.3.4.1 Spectrum due to modulation and wideband noise . 38 5.3.4.1.1 Test case . 38 5.3.4.1.2 Test Environment . 39 5.3.4.2 Switching transients spectrum . 39 5.3.4.2.1 Test case . 39 5.3.4.2.2 Test Environment . 40 5.3.5 Spurious emissions from the transmitter antenna connector . 40 5.3.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit band . 40 5.3.5.1.1 Test case . 40 5.3.5.1.2 Test Environment . 40 5.3.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit band . 41 5.3.5.2.1 For BTS not belonging to a multicarrier BTS class . 41 5.3.5.2.2 For BTS belonging to a multicarrier BTS class . 42 SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 5 5.3.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the BTS transmit band . 43 5.3.5.3.1 Test case . 44 5.3.5.3.2 Test Environment . 44 5.3.6 Intermodulation attenuation . 44 5.3.6.1 Test case . 44 5.3.6.2 Test Environment . 46 5.3.7 Intra Base Station System intermodulation attenuation . 46 5.3.7.1 Test case . 46 5.3.7.2 Test Environment . 47 5.3.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 47 5.3.8.1 Test case . 47 5.3.8.2 Test Environment . 49 5.3.9 Void . 50 5.3.10 Void . 50 5.3.11 Reference Interference Level . 50 5.3.11.1 Test case . 50 5.3.11.2 Test Environment . 58 5.3.12 Blocking Characteristics . 58 5.3.12.1 Test case . 58 5.3.12.2 Test Environment . 64 5.3.13 Intermodulation characteristics . 64 5.3.13.1 Test case . 64 5.3.13.2 Test Environment . 65 5.3.14 AM suppression . 65 5.3.14.1 Test case . 65 5.3.14.2 Test Environment . 67 5.3.15 Spurious emissions from the receiver antenna connector . 67 5.3.15.1 Test case . 67 5.3.15.2 Test Environment . 67 5.3.16 Radiated spurious emissions . 68 5.3.16.1 Test case . 69 5.3.16.2 Test Environment . 70 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 71 Annex B (normative): General test conditions and declarations . 73 B.1 Declaration by manufacturer . 73 B.1.1 Output power and determination of power class . 73 B.1.2 Specified frequency range . 74 B.1.3 Frequency hopping . 74 B.1.4 Void . 74 B.1.5 Downlink discontinuous transmission (DTX) . 74 B.2 BTS Configurations . 74 B.2.1 Receiver diversity . 75 B.2.2 Duplexers . 75 B.2.3 Power supply options . 76 B.2.4 Ancillary RF amplifiers . 76 B.2.5 BSS using antenna arrays . 76 B.2.6 BTS supporting 8-PSK modulation . 78 B.2.7 BTS supporting additional modulations in EGPRS2 . 78 B.2.8 Supported Symbol Rate . 78 B.2.9 Support of RTTI and/or FANR . 78 B.2.10 Multicarrier BTS . 78 B.2.11 BTS supporting VAMOS . 79 B.2.12 BTS supporting ER-GSM . 80 Annex C (normative): Test environments . 81 C.1 Normal test environment . 81 SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 6 C.2 Extreme test environment . 81 C.2.1 Extreme temperature . 81 C.3 Void . 82 C.4 Power supply . 82 Annex D: Void . 83 Annex E (informative): Bibliography . 84 History . 85
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The update to version 12.1.1 of the present document includes the following major changes: • Inclusion of BTS equipment supporting operation in the ER-GSM 900 band. The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.5]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
National transposition dates Date of adoption of this EN: 24 February 2015 Date of latest announcement of this EN (doa): 31 May 2015 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 November 2015 Date of withdrawal of any conflicting National Standard (dow): 30 November 2016
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 8 1 Scope The present document applies to the following radio equipment type: 1) GSM base stations. Table 1-1: GSM Base Station System frequency bands GSM band Direction of transmission GSM Base Station System relevant frequency bands P-GSM 900 Transmit
935 MHz to 960 MHz Receive
890 MHz to 915 MHz E-GSM 900 Transmit
925 MHz to 960 MHz Receive
880 MHz to 915 MHz R-GSM 900 Transmit
921 MHz to 960 MHz Receive 876 MHz to 915 MHz ER-GSM 900 Transmit
918 MHz to 960 MHz Receive 873 MHz to 915 MHz DCS 1 800 Transmit 1 805 MHz to 1 880 MHz Receive 1 710 MHz to 1 785 MHz GSM 450 Transmit 460,4 MHz to 467,6 MHz Receive 450,4 MHz to 457,6 MHz GSM 480 Transmit 488,8 MHz to 496 MHz Receive 478,8 MHz to 486 MHz
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2, which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In regards to interference to systems operating in adjacent bands guidance for single carrier BTS and multicarrier BTS is provided in ECC Report 146 [i.4]. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] ETSI TR 121 905 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Vocabulary for 3GPP Specifications (3GPP TR 21.905 version 12.0.0 Release 12)". [2] ETSI TS 151 021 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Base Station System (BSS) equipment specification; Radio aspects (3GPP TS 51.021 version 12.2.0 Release 12)". SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 9 [3] ETSI TS 145 002 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Multiplexing and multiple access on the radio path (3GPP TS 45.002 version 12.2.0 Release 12)". [4] ETSI TS 145 004 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Modulation (3GPP TS 45.004 version 12.0.0 Release 12)". [5] ETSI TS 145 005 (V12.3.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Radio Transmission and reception (3GPP TS 45.005 version 12.3.0 Release 12)". [6] Void. [7] ETSI TS 145 010 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Radio subsystem synchronization (3GPP TS 45.010 version 12.0.0 Release 12)". [8] Void. [9] Void. [10] ETSI EN 300 019-1-0 (V2.1.2) (09-2003): "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction". [11] ETSI EN 300 019-1-3 (V2.4.1) (04-2014): "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of environmental conditions; Stationary use at weatherprotected locations". [12] ETSI EN 300 019-1-4 (V2.2.1) (04-2014): "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-4: Classification of environmental conditions; Stationary use at non-weatherprotected locations". [13] Void. [14] Void. [15] ETSI TS 124 022 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); Radio Link Protocol (RLP) for circuit switched bearer and teleservices (3GPP TS 24.022 version 12.0.0 Release 12)". [16] ETSI TS 148 020 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Rate adaption on the Base Station System - Mobile-services Switching Centre (BSS-MSC) interface (3GPP TS 48.020 version 12.0.0 Release 12)". [17] Recommendation ITU-T O.153 (10-1992): "Basic Parameters for the measurement of error performance at bit rates below the primary rate". [18] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain". [19] Void. [20] Void. [21] Void. [22] ETSI EN 300 019-2-3 (V2.3.1) (04-2013): "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-3: Specification of environmental tests; Stationary use at weatherprotected locations". [23] ETSI EN 300 019-2-4 (V2.3.1) (08-2013): "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-4: Specification of environmental tests; Stationary use at non-weatherprotected locations". [24] IEC EN 60721-1 (ed.2.2, 10-2002): "Classification of environmental conditions: Part 1: Environmental parameters and their severities". [25] IEC EN 60721-2-1 (ed.2.0, 06-2013): "Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity". SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 10 [26] IEC EN 60721-2-4 (ed.1.1, 10-2002): "Classification of environmental conditions - Part 2-4: Environmental conditions appearing in nature - Solar radiation and temperature". [27] IEC EN 60721-3-0 (ed.1.1, 10-2002): "Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Introduction". [28] ETSI EN 301 908-1 (V6.2.1) (04-2013): "IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements". [29] ETSI EN 301 908-18 (V7.1.2) (07-2014): "IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 18: E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. [i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the R&TTE Directive". [i.4] ECC Report 146: "Compatibility between GSM MCBTS and other services (TRR, RSBN/PRMG, HC-SDMA, GSM-R, DME, MIDS, DECT) operating in the 900 and 1800 MHz frequency bands", 6th July 2010. [i.5] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. [i.6] ETSI TS 144 060 (V12.2.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station System (BSS) interface; Radio Link Control / Medium Access Control (RLC/MAC) protocol (3GPP TS 44.060 version 12.2.0 Release 12)". [i.7] CEPT/ERC/Recommendation 74-01E (01-2011): "Unwanted emissions in the spurious domain". [i.8] ETSI TR 100 028 (all parts) (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.9] ETSI TS 145 001 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Physical layer on the radio path; General description (3GPP TS 45.001 version 12.0.0 Release 12)". [i.10] ETSI TR 145 050 (V12.0.0) (10-2014): "Digital cellular telecommunications system (Phase 2+); Background for Radio Frequency (RF) requirements (3GPP TR 45.050 version 12.0.0 Release 12)". SIST EN 301 502 V12.1.1:2015
ETSI ETSI EN 301 502 V12.1.1 (2015-03) 11 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TR 121 905 [1] and the following apply: 8-PSK: Modulation type as defined in TS 145 004 [4], clause 3. 16-QAM: Modulation type as defined in TS 145 004 [4], clause 4 for EGPRS2-A and clause 5 for EGRPS2-B. 32-QAM: Modulation type as defined in TS 145 004 [4], clause 4 for EGPRS2-A and clause 5 for EGRPS2-B. ancillary RF amplifier: piece of equipment, which when connected by RF coaxial cables to the BTS, has the primary function to provide amplification between the transmit and/or receive antenna connector of a BTS and an antenna without requiring any control signal to fulfil its amplifying function AQPSK: Modulation type as defined in TS 145 004 [4], clause 6. base station RF bandwidth: instantaneous bandwidth in which a BTS belonging to a multicarrier BTS class transmits or transmits and receives multiple carriers simultaneously Base Station System Test Equipment (BSSTE): See annex B in TS 151 021 [2]. BSS: BTS or integrated BSS NOTE: If a separate BSC is required to perform tests on a BTS, the BSC may be regarded as test equipment and the environmental conditions of the BSC need not be controlled. carrier frequency: centre of the ARFCN under test circuit switched logical channels: all the standard GSM logical channels, including traffic channels (TCH), common control channels (RACH) and dedicated control channels (SDCCH, SACCH) E-GSM: extended GSM 900 band (includes P-GSM band) ECSD: any subset of the E-TCH traffic channels and related control channels EGPRS: any subset of the packet traffic channels PDTCH/MCS-1 to MCS-9 and related control channels EGPRS2: any of EGPRS2-A and EGPRS2-B EGPRS2-A: packet traffic channels utilizing any subse
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...