ETSI EN 301 908-14 V7.1.1 (2015-07)
IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)
IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)
REN/MSG-TFES-011-14
Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 14. del: Bazne postaje za razviti prizemni radijski dostop za UMTS (E-UTRA)
Ta dokument se uporablja za radijsko opremo naslednjih vrst:
1) bazne postaje za razviti prizemni radijski dostop (E-UTRA). Ta dokument zajema zahteve za bazne postaje E-UTRA za izdaje 8, 9, 10 in 11 standarda 3GPP. To vključuje zahteve za pasove bazne postaje E-UTRA in pasove bazne postaje E-UTRA CA iz izdaje 12 standarda 3GPP.
Ta dokument zajema določbe člena 3(2) Direktive 1999/5/ES [i.2] (direktive R&TTE), ki določa, da »[...] mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.«
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks;Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive;Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-14 V7.1.1SIST EN 301 908-14 V7.1.1:2015en,fr,de01-oktober-2015SIST EN 301 908-14 V7.1.1:2015SLOVENSKI
STANDARD
SIST EN 301 908-14 V7.1.1:2015
ETSI EN 301 908-14 V7.1.1 (2015-07) IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)
HARMONISED EUROPEAN STANDARD SIST EN 301 908-14 V7.1.1:2015
ETSI ETSI EN 301 908-14 V7.1.1 (2015-07)2
Reference REN/MSG-TFES-011-14 Keywords 3G, 3GPP, cellular, digital, E-UTRA, IMT, IMT-2000, LTE, mobile, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-14 V7.1.1:2015
ETSI ETSI EN 301 908-14 V7.1.1 (2015-07)3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 Introduction . 6 1 Scope . 7 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 14 3.3 Abbreviations . 15 4 Technical requirements specifications . 16 4.1 Environmental profile . 16 4.2 Conformance requirements . 16 4.2.1 Introduction. 16 4.2.2 Operating band unwanted emissions . 20 4.2.2.1 Definition . 20 4.2.2.2 Limits . 20 4.2.2.2.1 Limits for Wide Area BS (Bands 1, 3, 8, 32, 33 and 34) . 21 4.2.2.2.2 Limits for Wide Area BS (Bands 7, 22, 38, 40, 42 and 43) . 23 4.2.2.2.3 Limits for Wide Area BS (Band 20 and 28) . 25 4.2.2.2.4 Limits for Local Area BS . 26 4.2.2.2.5 Limits for Home BS . 27 4.2.2.2.6 Limits for protection of DTT . 29 4.2.2.2.7 Limits for protection of adjacent band services . 30 4.2.2.2.8 Limits for medium range BS . 30 4.2.2.3 Conformance . 34 4.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 34 4.2.3.1 Definition . 34 4.2.3.2 Void. 34 4.2.3.3 Void. 34 4.2.3.4 Limits . 34 4.2.3.4.1 ACLR Limits . 35 4.2.3.4.2 Cumulative ACLR test requirement in non-contiguous spectrum limits . 36 4.2.3.5 Conformance . 37 4.2.4 Transmitter spurious emissions . 37 4.2.4.1 Definition . 37 4.2.4.2 Limits . 38 4.2.4.2.1 Spurious emissions . 38 4.2.4.2.2 Co-existence with other systems . 38 4.2.4.2.3 Protection of the BS receiver of own or different BS . 40 4.2.4.2.4 Co-existence with Home BS operating in other bands . 40 4.2.4.3 Conformance . 41 4.2.5 Base Station maximum output power . 41 4.2.5.1 Definition . 41 4.2.5.2 Limit . 41 4.2.5.3 Conformance . 42 4.2.6 Transmitter intermodulation . 42 4.2.6.1 Definition . 42 4.2.6.2 Limit . 42 4.2.6.3 Conformance . 43 4.2.7 Receiver spurious emissions . 43 4.2.7.1 Definition . 43 SIST EN 301 908-14 V7.1.1:2015
ETSI ETSI EN 301 908-14 V7.1.1 (2015-07)4 4.2.7.2 Limit . 43 4.2.7.3 Conformance . 43 4.2.8 Blocking characteristics . 44 4.2.8.1 Definition . 44 4.2.8.2 Limit . 44 4.2.8.3 Conformance . 46 4.2.9 Receiver intermodulation characteristics . 47 4.2.9.1 Definition . 47 4.2.9.2 Limit . 47 4.2.9.3 Conformance . 50 4.2.10 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 50 4.2.10.1 Definition . 50 4.2.10.2 Limit . 50 4.2.10.3 Conformance . 54 4.2.11 Home BS output power for adjacent UTRA channel protection. 54 4.2.11.1 Definition . 54 4.2.11.2 Limit . 54 4.2.11.3 Conformance . 55 4.2.12 Home BS output power for adjacent E-UTRA channel protection . 55 4.2.12.1 Definition and applicability . 55 4.2.12.2 Limit . 55 4.2.12.3 Conformance . 56 4.2.13 Home BS output power for co-channel E-UTRA protection . 56 4.2.13.1 Definition and applicability . 56 4.2.13.2 Limit . 56 4.2.13.3 Conformance . 57 5 Testing for compliance with technical requirements . 57 5.1 Environmental conditions for testing . 57 5.2 Interpretation of the measurement results . 58 5.3 Essential radio test suites . 59 5.3.1 Operating band unwanted emissions . 59 5.3.1.1 Initial conditions . 59 5.3.1.2 Procedure . 60 5.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 60 5.3.2.1 Initial conditions . 60 5.3.2.2 Procedure . 61 5.3.3 Transmitter spurious emissions . 61 5.3.3.1 Initial conditions . 61 5.3.3.2 Procedure . 62 5.3.4 Base Station maximum output power . 62 5.3.4.1 Initial conditions . 62 5.3.4.2 Procedure . 62 5.3.5 Transmitter intermodulation . 63 5.3.5.1 Initial conditions . 63 5.3.5.2 Procedures . 63 5.3.6 Receiver spurious emissions . 64 5.3.6.1 Initial conditions . 64 5.3.6.2 Procedure . 64 5.3.7 Blocking characteristics . 65 5.3.7.1 Initial conditions . 65 5.3.7.2 Procedure . 65 5.3.8 Receiver intermodulation characteristics . 66 5.3.8.1 Initial conditions . 66 5.3.8.2 Procedures . 66 5.3.9 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 67 5.3.9.1 Initial conditions . 67 5.3.9.2 Procedure for Adjacent Channel Selectivity . 67 5.3.9.3 Procedure for narrow-band blocking . 67 5.3.10 Home BS output power for adjacent UTRA channel protection. 68 5.3.10.1 Initial conditions . 68 5.3.10.2 Procedure . 68 SIST EN 301 908-14 V7.1.1:2015
ETSI ETSI EN 301 908-14 V7.1.1 (2015-07)5 5.3.11 Home BS output power for adjacent E-UTRA channel protection . 69 5.3.11.1 Initial conditions . 69 5.3.11.2 Procedure . 69 5.3.12 Home BS output power for co-channel E-UTRA protection . 70 5.3.12.1 Initial conditions . 70 5.3.12.2 Procedure . 70 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 72 Annex B (normative): Base Station configurations . 74 B.1 Reception with multiple receiver antenna connectors, receiver diversity . 74 B.2 Duplexers . 74 B.3 Power supply options . 74 B.4 Ancillary RF amplifiers . 75 B.5 BS using antenna arrays . 75 B.5.1 Receiver tests . 76 B.5.2 Transmitter tests . 76 B.6 Transmission with multiple transmitter antenna connectors . 77 B.7 BS with integrated Iuant BS modem . 77 Annex C (informative): Environmental profile specification . 78 Annex D: Void . 79 Annex E (informative): Bibliography . 80 History . 81
SIST EN 301 908-14 V7.1.1:2015
ETSI ETSI EN 301 908-14 V7.1.1 (2015-07)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonised Standard under the Directive 1999/5/EC [i.2]. The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A. The present document is part 14 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.7].
National transposition dates Date of adoption of this EN: 13 July 2015 Date of latest announcement of this EN (doa): 31 October 2015 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 April 2016 Date of withdrawal of any conflicting National Standard (dow): 30 April 2017
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in ETSI EG 201 399 [i.3]. SIST EN 301 908-14 V7.1.1:2015
ETSI ETSI EN 301 908-14 V7.1.1 (2015-07)7 1 Scope The present document applies to the following radio equipment types: 1) Base Station for Evolved Universal Terrestrial Radio Access (E-UTRA). This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1. Table 1-1: E-UTRA Base Station operating bands E-UTRA band Direction of transmission E-UTRA Base Station operating bands 1 Transmit
2 110 MHz to 2 170 MHz Receive
1 920 MHz to 1 980 MHz 3 Transmit
1 805 MHz to 1 880 MHz Receive
1 710 MHz to 1 785 MHz 7 Transmit
2 620 MHz to 2 690 MHz Receive
2 500 MHz to 2 570 MHz 8 Transmit
925 MHz to 960 MHz Receive
880 MHz to 915 MHz 20 Transmit
791 MHz to 821 MHz Receive
832 MHz to 862 MHz 22 Transmit
3 510 MHz to 3 590 MHz Receive
3 410 MHz to 3 490 MHz 28 Transmit 703 MHz to 748 MHz Receive 758 MHz to 803 MHz 32 (note) Transmit 1 452 MHz to 1 496 MHz Receive N/A 33 Transmit and Receive 1 900 MHz to 1 920 MHz 34 Transmit and Receive 2 010 MHz to 2 025 MHz 38 Transmit and Receive 2 570 MHz to 2 620 MHz 40 Transmit and Receive 2 300 MHz to 2 400 MHz 42 Transmit and Receive 3 400 MHz to 3 600 MHz 43 Transmit and Receive 3 600 MHz to 3 800 MHz NOTE: Restricted to E-UTRA operation when carrier aggregation is configured. The downlink operating band is paired with the uplink operating band (external) of the carrier aggregation configuration that is supporting the configured Pcell.
The present document covers requirements for E-UTRA Base Stations for 3GPP Release 8, 9, 10 and 11. This includes the requirements for E UTRA Base Station operating bands and E-UTRA CA operating bands from 3GPP Release 12. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2, which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. SIST EN 301 908-14 V7.1.1:2015
ETSI ETSI EN 301 908-14 V7.1.1 (2015-07)8 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applie
...
ETSI EN 301 908-14 V7.1.1 (2015-07)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA)
Base Stations (BS)
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-14 V7.1.1 (2015-07)
Reference
REN/MSG-TFES-011-14
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, LTE, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-14 V7.1.1 (2015-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 14
3.3 Abbreviations . 15
4 Technical requirements specifications . 16
4.1 Environmental profile . 16
4.2 Conformance requirements . 16
4.2.1 Introduction. 16
4.2.2 Operating band unwanted emissions . 20
4.2.2.1 Definition . 20
4.2.2.2 Limits . 20
4.2.2.2.1 Limits for Wide Area BS (Bands 1, 3, 8, 32, 33 and 34) . 21
4.2.2.2.2 Limits for Wide Area BS (Bands 7, 22, 38, 40, 42 and 43) . 23
4.2.2.2.3 Limits for Wide Area BS (Band 20 and 28) . 25
4.2.2.2.4 Limits for Local Area BS . 26
4.2.2.2.5 Limits for Home BS . 27
4.2.2.2.6 Limits for protection of DTT . 29
4.2.2.2.7 Limits for protection of adjacent band services . 30
4.2.2.2.8 Limits for medium range BS . 30
4.2.2.3 Conformance . 34
4.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 34
4.2.3.1 Definition . 34
4.2.3.2 Void. 34
4.2.3.3 Void. 34
4.2.3.4 Limits . 34
4.2.3.4.1 ACLR Limits . 35
4.2.3.4.2 Cumulative ACLR test requirement in non-contiguous spectrum limits . 36
4.2.3.5 Conformance . 37
4.2.4 Transmitter spurious emis sions . 37
4.2.4.1 Definition . 37
4.2.4.2 Limits . 38
4.2.4.2.1 Spurious emissions . 38
4.2.4.2.2 Co-existence with other systems . 38
4.2.4.2.3 Protection of the BS receiver of own or different BS . 40
4.2.4.2.4 Co-existence with Home BS operating in other bands . 40
4.2.4.3 Conformance . 41
4.2.5 Base Station maximum output power . 41
4.2.5.1 Definition . 41
4.2.5.2 Limit . 41
4.2.5.3 Conformance . 42
4.2.6 Transmitter intermodulation . 42
4.2.6.1 Definition . 42
4.2.6.2 Limit . 42
4.2.6.3 Conformance . 43
4.2.7 Receiver spurious emissions . 43
4.2.7.1 Definition . 43
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-14 V7.1.1 (2015-07)
4.2.7.2 Limit . 43
4.2.7.3 Conformance . 43
4.2.8 Blocking characteristics . 44
4.2.8.1 Definition . 44
4.2.8.2 Limit . 44
4.2.8.3 Conformance . 46
4.2.9 Receiver intermodulation characteristics . 47
4.2.9.1 Definition . 47
4.2.9.2 Limit . 47
4.2.9.3 Conformance . 50
4.2.10 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 50
4.2.10.1 Definition . 50
4.2.10.2 Limit . 50
4.2.10.3 Conformance . 54
4.2.11 Home BS output power for adjacent UTRA channel protection. 54
4.2.11.1 Definition . 54
4.2.11.2 Limit . 54
4.2.11.3 Conformance . 55
4.2.12 Home BS output power for adjacent E-UTRA channel protection . 55
4.2.12.1 Definition and applicability . 55
4.2.12.2 Limit . 55
4.2.12.3 Conformance . 56
4.2.13 Home BS output power for co-channel E-UTRA protection . 56
4.2.13.1 Definition and applicability . 56
4.2.13.2 Limit . 56
4.2.13.3 Conformance . 57
5 Testing for compliance with technical requirements . 57
5.1 Environmental conditions for testing . 57
5.2 Interpretation of the measurement results . 58
5.3 Essential radio test suites . 59
5.3.1 Operating band unwanted emissions . 59
5.3.1.1 Initial conditions . 59
5.3.1.2 Procedure . 60
5.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 60
5.3.2.1 Initial conditions . 60
5.3.2.2 Procedure . 61
5.3.3 Transmitter spurious emis sions . 61
5.3.3.1 Initial conditions . 61
5.3.3.2 Procedure . 62
5.3.4 Base Station maximum output power . 62
5.3.4.1 Initial conditions . 62
5.3.4.2 Procedure . 62
5.3.5 Transmitter intermodulation . 63
5.3.5.1 Initial conditions . 63
5.3.5.2 Procedures . 63
5.3.6 Receiver spurious emissions . 64
5.3.6.1 Initial conditions . 64
5.3.6.2 Procedure . 64
5.3.7 Blocking characteristics . 65
5.3.7.1 Initial conditions . 65
5.3.7.2 Procedure . 65
5.3.8 Receiver intermodulation characteristics . 66
5.3.8.1 Initial conditions . 66
5.3.8.2 Procedures . 66
5.3.9 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 67
5.3.9.1 Initial conditions . 67
5.3.9.2 Procedure for Adjacent Channel Selectivity . 67
5.3.9.3 Procedure for narrow-band blocking . 67
5.3.10 Home BS output power for adjacent UTRA channel protection. 68
5.3.10.1 Initial conditions . 68
5.3.10.2 Procedure . 68
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-14 V7.1.1 (2015-07)
5.3.11 Home BS output power for adjacent E-UTRA channel protection . 69
5.3.11.1 Initial conditions . 69
5.3.11.2 Procedure . 69
5.3.12 Home BS output power for co-channel E-UTRA protection . 70
5.3.12.1 Initial conditions . 70
5.3.12.2 Procedure . 70
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 72
Annex B (normative): Base Station configurations . 74
B.1 Reception with multiple receiver antenna connectors, receiver diversity . 74
B.2 Duplexers . 74
B.3 Power supply options . 74
B.4 Ancillary RF amplifiers . 75
B.5 BS using antenna arrays . 75
B.5.1 Receiver tests . 76
B.5.2 Transmitter tests . 76
B.6 Transmission with multiple transmitter antenna connectors . 77
B.7 BS with integrated Iuant BS modem . 77
Annex C (informative): Environmental profile specification . 78
Annex D: Void . 79
Annex E (informative): Bibliography . 80
History . 81
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-14 V7.1.1 (2015-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonised Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 14 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.7].
National transposition dates
Date of adoption of this EN: 13 July 2015
Date of latest announcement of this EN (doa): 31 October 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 April 2016
Date of withdrawal of any conflicting National Standard (dow): 30 April 2017
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in ETSI EG 201 399 [i.3].
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-14 V7.1.1 (2015-07)
1 Scope
The present document applies to the following radio equipment types:
1) Base Station for Evolved Universal Terrestrial Radio Access (E-UTRA).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Base Station operating bands
E-UTRA band Direction of transmission E-UTRA Base Station operating bands
1 Transmit 2 110 MHz to 2 170 MHz
Receive 1 920 MHz to 1 980 MHz
3 Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
7 Transmit 2 620 MHz to 2 690 MHz
Receive 2 500 MHz to 2 570 MHz
8 Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
20 Transmit 791 MHz to 821 MHz
Receive 832 MHz to 862 MHz
22 Transmit 3 510 MHz to 3 590 MHz
Receive 3 410 MHz to 3 490 MHz
Transmit 703 MHz to 748 MHz
28
Receive 758 MHz to 803 MHz
Transmit 1 452 MHz to 1 496 MHz
32
(note) Receive N/A
33 Transmit and Receive 1 900 MHz to 1 920 MHz
34 Transmit and Receive 2 010 MHz to 2 025 MHz
38 Transmit and Receive 2 570 MHz to 2 620 MHz
40 Transmit and Receive 2 300 MHz to 2 400 MHz
42 Transmit and Receive 3 400 MHz to 3 600 MHz
43 Transmit and Receive 3 600 MHz to 3 800 MHz
NOTE: Restricted to E-UTRA operation when carrier aggregation is configured. The downlink operating
band is paired with the uplink operating band (external) of the carrier aggregation configuration
that is supporting the configured Pcell.
The present document covers requirements for E-UTRA Base Stations for 3GPP Release 8, 9, 10 and 11. This includes
the requirements for E UTRA Base Station operating bands and E-UTRA CA operating bands from 3GPP Release 12.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-14 V7.1.1 (2015-07)
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Refer
...
Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA)
Base Stations (BS)
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
Reference
REN/MSG-TFES-011-14
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, LTE, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 14
3.3 Abbreviations . 15
4 Technical requirements specifications . 16
4.1 Environmental profile . 16
4.2 Conformance requirements . 16
4.2.1 Introduction. 17
4.2.2 Operating band unwanted emissions . 20
4.2.2.1 Definition . 20
4.2.2.2 Limits . 20
4.2.2.2.1 Limits for Wide Area BS (Bands 1, 3, 8, 32, 33 and 34) . 21
4.2.2.2.2 Limits for Wide Area BS (Bands 7, 22, 38, 40, 42 and 43) . 23
4.2.2.2.3 Limits for Wide Area BS (Band 20 and 28) . 25
4.2.2.2.4 Limits for Local Area BS . 26
4.2.2.2.5 Limits for Home BS . 27
4.2.2.2.6 Limits for protection of DTT . 29
4.2.2.2.7 Limits for protection of adjacent band services . 30
4.2.2.2.8 Limits for medium range BS . 30
4.2.2.3 Conformance . 34
4.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 34
4.2.3.1 Definition . 34
4.2.3.2 Void. 34
4.2.3.3 Void. 34
4.2.3.4 Limits . 34
4.2.3.4.1 ACLR Limits . 35
4.2.3.4.2 Cumulative ACLR test requirement in non-contiguous spectrum limits . 36
4.2.3.5 Conformance . 37
4.2.4 Transmitter spurious emis sions . 37
4.2.4.1 Definition . 37
4.2.4.2 Limits . 38
4.2.4.2.1 Spurious emissions . 38
4.2.4.2.2 Co-existence with other systems . 38
4.2.4.2.3 Protection of the BS receiver of own or different BS . 40
4.2.4.2.4 Co-existence with Home BS operating in other bands . 40
4.2.4.3 Conformance . 41
4.2.5 Base Station maximum output power . 41
4.2.5.1 Definition . 41
4.2.5.2 Limit . 41
4.2.5.3 Conformance . 42
4.2.6 Transmitter intermodulation . 42
4.2.6.1 Definition . 42
4.2.6.2 Limit . 42
4.2.6.3 Conformance . 43
4.2.7 Receiver spurious emissions . 43
4.2.7.1 Definition . 43
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
4.2.7.2 Limit . 43
4.2.7.3 Conformance . 44
4.2.8 Blocking characteristics . 44
4.2.8.1 Definition . 44
4.2.8.2 Limit . 44
4.2.8.3 Conformance . 46
4.2.9 Receiver intermodulation characteristics . 47
4.2.9.1 Definition . 47
4.2.9.2 Limit . 47
4.2.9.3 Conformance . 50
4.2.10 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 50
4.2.10.1 Definition . 50
4.2.10.2 Limit . 50
4.2.10.3 Conformance . 54
4.2.11 Home BS output power for adjacent UTRA channel protection. 54
4.2.11.1 Definition . 54
4.2.11.2 Limit . 54
4.2.11.3 Conformance . 55
4.2.12 Home BS output power for adjacent E-UTRA channel protection . 55
4.2.12.1 Definition and applicability . 55
4.2.12.2 Limit . 55
4.2.12.3 Conformance . 56
4.2.13 Home BS output power for co-channel E-UTRA protection . 56
4.2.13.1 Definition and applicability . 56
4.2.13.2 Limit . 57
4.2.13.3 Conformance . 58
5 Testing for compliance with technical requirements . 58
5.1 Environmental conditions for testing . 58
5.2 Interpretation of the measurement results . 58
5.3 Essential radio test suites . 59
5.3.1 Operating band unwanted emissions . 60
5.3.1.1 Initial conditions . 60
5.3.1.2 Procedure . 60
5.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 60
5.3.2.1 Initial conditions . 60
5.3.2.2 Procedure . 61
5.3.3 Transmitter spurious emis sions . 61
5.3.3.1 Initial conditions . 61
5.3.3.2 Procedure . 62
5.3.4 Base Station maximum output power . 62
5.3.4.1 Initial conditions . 62
5.3.4.2 Procedure . 63
5.3.5 Transmitter intermodulation . 63
5.3.5.1 Initial conditions . 63
5.3.5.2 Procedures . 63
5.3.6 Receiver spurious emissions . 64
5.3.6.1 Initial conditions . 64
5.3.6.2 Procedure . 64
5.3.7 Blocking characteristics . 65
5.3.7.1 Initial conditions . 65
5.3.7.2 Procedure . 65
5.3.8 Receiver intermodulation characteristics . 66
5.3.8.1 Initial conditions . 66
5.3.8.2 Procedures . 66
5.3.9 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 67
5.3.9.1 Initial conditions . 67
5.3.9.2 Procedure for Adjacent Channel Selectivity . 67
5.3.9.3 Procedure for narrow-band blocking . 68
5.3.10 Home BS output power for adjacent UTRA channel protection. 68
5.3.10.1 Initial conditions . 68
5.3.10.2 Procedure . 68
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
5.3.11 Home BS output power for adjacent E-UTRA channel protection . 69
5.3.11.1 Initial conditions . 69
5.3.11.2 Procedure . 69
5.3.12 Home BS output power for co-channel E-UTRA protection . 70
5.3.12.1 Initial conditions . 70
5.3.12.2 Procedure . 70
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 72
Annex B (normative): Base Station configurations . 74
B.1 Reception with multiple receiver antenna connectors, receiver diversity . 74
B.2 Duplexers . 74
B.3 Power supply options . 74
B.4 Ancillary RF amplifiers . 75
B.5 BS using antenna arrays . 75
B.5.1 Receiver tests . 76
B.5.2 Transmitter tests . 76
B.6 Transmission with multiple transmitter antenna connectors . 77
B.7 BS with integrated Iuant BS modem . 77
Annex C (informative): Environmental profile specification . 78
Annex D: Void . 79
Annex E (informative): Bibliography . 80
History . 81
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile
Standards Group (MSG), and is now submitted for the Vote phase of the ETSI standards EN Approval Procedure.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 14 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.7].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in ETSI EG 201 399 [i.3].
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
1 Scope
The present document applies to the following radio equipment types:
1) Base Station for Evolved Universal Terrestrial Radio Access (E-UTRA).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Base Station operating bands
E-UTRA band Direction of transmission E-UTRA Base Station operating bands
1 Transmit 2 110 MHz to 2 170 MHz
Receive 1 920 MHz to 1 980 MHz
3 Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
7 Transmit 2 620 MHz to 2 690 MHz
Receive 2 500 MHz to 2 570 MHz
8 Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
20 Transmit 791 MHz to 821 MHz
Receive 832 MHz to 862 MHz
22 Transmit 3 510 MHz to 3 590 MHz
Receive 3 410 MHz to 3 490 MHz
Transmit 703 MHz to 748 MHz
28
Receive 758 MHz to 803 MHz
Transmit N/A
32
(note) Receive 1 452 MHz to 1 496 MHz
33 Transmit and Receive 1 900 MHz to 1 920 MHz
34 Transmit and Receive 2 010 MHz to 2 025 MHz
38 Transmit and Receive 2 570 MHz to 2 620 MHz
40 Transmit and Receive 2 300 MHz to 2 400 MHz
42 Transmit and Receive 3 400 MHz to 3 600 MHz
43 Transmit and Receive 3 600 MHz to 3 800 MHz
NOTE: Restricted to E-UTRA operation when carrier aggregation is configured. The downlink operating
band is paired with the uplink operating band (external) of the carrier aggregation configuration
that is supporting the configured Pcell.
The present document covers requirements for E-UTRA Base Stations for 3GPP Release 8, 9, 10 and 11. This includes
the requirements for E UTRA Base Station operating bands and E-UTRA CA operating bands from 3GPP Release 12.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 908-14 V7.1.0 (2015-05)
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
re
...
Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA)
Base Stations (BS)
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
Reference
REN/MSG-TFES-011-14
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT,
IMT-2000, LTE, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2014.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Technical requirements specifications . 16
4.1 Environmental profile . 16
4.2 Conformance requirements . 16
4.2.1 Introduction. 16
4.2.2 Operating band unwanted emissions . 18
4.2.2.1 Definition . 18
4.2.2.2 Limits . 19
4.2.2.2.1 Limits for Wide Area BS (Bands 1, 3, 8, 33 and 34) . 20
4.2.2.2.2 Limits for Wide Area BS (Bands 7, 22, 38, 40, 42 and 43) . 21
4.2.2.2.3 Limits for Wide Area BS (Band 20) . 24
4.2.2.2.4 Limits for Local Area BS . 25
4.2.2.2.5 Limits for Home BS . 26
4.2.2.2.6 Limits for protection of DTT . 28
4.2.2.2.7 Limits for protection of adjacent band services . 29
4.2.2.2.8 Limits for medium range BS . 29
4.2.2.3 Conformance . 33
4.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 33
4.2.3.1 Definition . 33
4.2.3.2 Void. 34
4.2.3.3 Void. 34
4.2.3.4 Limits . 34
4.2.3.4.1 ACLR Limits . 34
4.2.3.4.2 Cumulative ACLR test requirement in non-contiguous spectrum limits . 35
4.2.3.5 Conformance . 36
4.2.4 Transmitter spurious emis sions . 37
4.2.4.1 Definition . 37
4.2.4.2 Limits . 37
4.2.4.2.1 Spurious emissions . 37
4.2.4.2.2 Co-existence with other systems . 37
4.2.4.2.3 Protection of the BS receiver of own or different BS . 39
4.2.4.2.4 Co-existence with Home BS operating in other bands . 39
4.2.4.3 Conformance . 40
4.2.5 Base Station maximum output power . 40
4.2.5.1 Definition . 41
4.2.5.2 Limit . 41
4.2.5.3 Conformance . 41
4.2.6 Transmitter intermodulation . 41
4.2.6.1 Definition . 41
4.2.6.2 Limit . 41
4.2.6.3 Conformance . 42
4.2.7 Receiver spurious emissions . 42
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
4.2.7.1 Definition . 42
4.2.7.2 Limit . 43
4.2.7.3 Conformance . 43
4.2.8 Blocking characteristics . 43
4.2.8.1 Definition . 43
4.2.8.2 Limit . 44
4.2.8.3 Conformance . 46
4.2.9 Receiver intermodulation characteristics . 46
4.2.9.1 Definition . 46
4.2.9.2 Limit . 47
4.2.9.3 Conformance . 50
4.2.10 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 50
4.2.10.1 Definition . 50
4.2.10.2 Limit . 50
4.2.10.3 Conformance . 54
4.2.11 Home BS output power for adjacent UTRA channel protection. 54
4.2.11.1 Definition . 54
4.2.11.2 Limit . 54
4.2.11.3 Conformance . 55
4.2.12 Home BS output power for adjacent E-UTRA channel protection . 55
4.2.12.1 Definition and applicability . 55
4.2.12.2 Limit . 55
4.2.12.3 Conformance . 56
4.2.13 Home BS output power for co-channel E-UTRA protection . 56
4.2.13.1 Definition and applicability . 56
4.2.13.2 Limit . 57
4.2.13.3 Conformance . 58
5 Testing for compliance with technical requirements . 58
5.1 Environmental conditions for testing . 58
5.2 Interpretation of the measurement results . 58
5.3 Essential radio test suites . 59
5.3.1 Operating band unwanted emissions . 60
5.3.1.1 Initial conditions . 60
5.3.1.2 Procedure . 60
5.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 61
5.3.2.1 Initial conditions . 61
5.3.2.2 Procedure . 61
5.3.3 Transmitter spurious emis sions . 62
5.3.3.1 Initial conditions . 62
5.3.3.2 Procedure . 62
5.3.4 Base Station maximum output power . 62
5.3.4.1 Initial conditions . 63
5.3.4.2 Procedure . 63
5.3.5 Transmitter intermodulation . 63
5.3.5.1 Initial conditions . 63
5.3.5.2 Procedures . 64
5.3.6 Receiver spurious emissions . 64
5.3.6.1 Initial conditions . 64
5.3.6.2 Procedure . 65
5.3.7 Blocking characteristics . 65
5.3.7.1 Initial conditions . 65
5.3.7.2 Procedure . 66
5.3.8 Receiver intermodulation characteristics . 66
5.3.8.1 Initial conditions . 67
5.3.8.2 Procedures . 67
5.3.9 Adjacent Channel Selectivity (ACS) and narrow-band blocking . 67
5.3.9.1 Initial conditions . 67
5.3.9.2 Procedure for Adjacent Channel Selectivity . 68
5.3.9.3 Procedure for narrow-band blocking . 68
5.3.10 Home BS output power for adjacent UTRA channel protection. 69
5.3.10.1 Initial conditions . 69
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
5.3.10.2 Procedure . 69
5.3.11 Home BS output power for adjacent E-UTRA channel protection . 69
5.3.11.1 Initial conditions . 69
5.3.11.2 Procedure . 70
5.3.12 Home BS output power for co-channel E-UTRA protection . 70
5.3.12.1 Initial conditions . 70
5.3.12.2 Procedure . 71
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 72
Annex B (normative): Base Station configurations . 74
B.1 Reception with multiple receiver antenna connectors, receiver diversity . 74
B.2 Duplexers . 74
B.3 Power supply options . 74
B.4 Ancillary RF amplifiers . 75
B.5 BS using antenna arrays . 75
B.5.1 Receiver tests . 76
B.5.2 Transmitter tests . 76
B.6 Transmission with multiple transmitter antenna connectors . 77
B.7 BS with integrated Iuant BS modem . 77
Annex C (informative): Environmental profile specification . 78
Annex D: Void . 79
Annex E (informative): Bibliography . 80
History . 81
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards
Group (MSG), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 14 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.7].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in ETSI EG 201 399 [i.3].
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
1 Scope
The present document applies to the following radio equipment types:
1) Base Station for Evolved Universal Terrestrial Radio Access (E-UTRA).
This radio equipment type is capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Base Station operating bands
E-UTRA band Direction of transmission E-UTRA Base Station operating bands
1 Transmit 2 110 MHz to 2 170 MHz
Receive 1 920 MHz to 1 980 MHz
3 Transmit 1 805 MHz to 1 880 MHz
Receive 1 710 MHz to 1 785 MHz
7 Transmit 2 620 MHz to 2 690 MHz
Receive 2 500 MHz to 2 570 MHz
8 Transmit 925 MHz to 960 MHz
Receive 880 MHz to 915 MHz
20 Transmit 791 MHz to 821 MHz
Receive 832 MHz to 862 MHz
22 Transmit 3 510 MHz to 3 590 MHz
Receive 3 410 MHz to 3 490 MHz
33 Transmit and Receive 1 900 MHz to 1 920 MHz
34 Transmit and Receive 2 010 MHz to 2 025 MHz
38 Transmit and Receive 2 570 MHz to 2 620 MHz
40 Transmit and Receive 2 300 MHz to 2 400 MHz
42 Transmit and Receive 3 400 MHz to 3 600 MHz
43 Transmit and Receive 3 600 MHz to 3 800 MHz
The present document covers requirements for E-UTRA Base Stations for 3GPP Release 8, 9, 10 and 11.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] Void.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-14 V7.0.1 (2014-11)
[2] ETSI TS 136 141 (V11.10.0) (09-2014): "LTE; Evolved Unive
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.