Coaxial communication cables - Part 13 - Sectional specification for semi-rigid cables with silicon dioxide dielectric

IEC 61196-13:2023 specifies the materials and cable construction for semi-rigid coaxial communication cables with silicon dioxide dielectric, IEC type designation, identification, marking and labelling, standard rating and characteristics, requirements of finished cables, quality assessment, delivery and storage, etc.
This part of IEC 61196 applies to semi-rigid coaxial communication cables with silicon dioxide dielectric and tubular outer conductor. These cables are intended for use in applications requiring extreme environments as well as in nuclear power plants, oil rigs and aircraft engines.

General Information

Status
Published
Publication Date
17-Aug-2023
Technical Committee
Drafting Committee
Current Stage
PPUB - Publication issued
Start Date
08-Sep-2023
Completion Date
18-Aug-2023
Ref Project

Buy Standard

Standard
IEC 61196-13:2023 - Coaxial communication cables - Part 13 - Sectional specification for semi-rigid cables with silicon dioxide dielectric Released:8/18/2023
English language
26 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC 61196-13 ®
Edition 1.0 2023-08
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 13: Sectional specification for semi-rigid cables with silicon dioxide
dielectric
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 61196-13 ®
Edition 1.0 2023-08
INTERNATIONAL
STANDARD
Coaxial communication cables –

Part 13: Sectional specification for semi-rigid cables with silicon dioxide

dielectric
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS  33.120.10 ISBN 978-2-8322-7371-5

– 2 – IEC 61196-13:2023 © IEC 2023
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Materials and cable construction . 8
4.1 General . 8
4.2 Inner conductor . 8
4.2.1 Conductor material . 8
4.2.2 Conductor construction . 8
4.3 Dielectric . 8
4.4 Outer conductor . 8
4.5 Sheath (when applicable) . 9
5 Type name and identification of cable . 9
5.1 Type . 9
5.2 Variants . 9
5.3 Cable marking . 9
6 Identification, marking and labelling . 10
6.1 Cable identification . 10
6.2 Cable marking (when required) . 10
6.3 Labelling . 10
7 Standard rating and characteristics . 10
7.1 Nominal characteristic impedance . 10
7.2 Rated temperature and humidity range . 10
7.3 Operating frequency . 10
7.4 Average and peak power . 10
7.5 Bending radius . 10
8 Requirements for finished cables . 11
8.1 General . 11
8.2 Electrical requirements . 11
8.3 Environmental requirements . 12
8.4 Mechanical requirements . 13
9 Quality assessment . 13
10 Delivery and storage . 13
Annex A (normative) Performance requirements of typical cables . 14
A.1 Performance requirements . 14
A.2 Attenuation . 14
Annex B (normative) Gamma irradiation . 16
B.1 General . 16
B.2 Apparatus . 16
B.2.1 General . 16
B.2.2 Radiation source. 16
B.2.3 Attenuation testing equipment . 16
B.2.4 Radiation dosimeter . 16
B.2.5 Temperature-controlled container . 16
B.2.6 Test reel . 17
B.3 Preparation of specimens . 17

B.3.1 Test sample length . 17
B.3.2 Test reel . 17
B.4 Procedure . 17
B.4.1 General . 17
B.4.2 Calibration of radiation source . 17
B.4.3 Preparation and pre-conditioning . 17
B.4.4 Attenuation measurement for environmental background radiation . 18
B.4.5 Attenuation measurement for adverse nuclear environment . 18
B.5 Calculations . 18
B.6 Results . 19
B.6.1 Information to be provided . 19
B.6.2 Information available upon request . 19
Annex C (normative) Thermal shock . 20
C.1 General . 20
C.2 Test samples . 20
C.3 Test equipment . 20
C.4 Procedure . 20
C.4.1 Initial measurements . 20
C.4.2 Thermal shock . 20
C.4.3 Final measurements . 21
Annex D (informative) Quality assessment . 22
D.1 General . 22
D.2 Qualification approval and its maintenance . 22
D.2.1 Qualification approval . 22
D.2.2 Capability approval . 22
D.2.3 Quality conformance inspection . 22
Bibliography . 26

Figure 1 – Cable marking . 9

Table 1 – Rated temperature and humidity . 10
Table 2 – Electrical requirements . 11
Table 3 – Environmental requirements . 12
Table 4 – Mechanical requirements. 13
Table A.1 – Performance requirements of typical cables . 14
Table A.2 – Maximum attenuation . 15
Table C.1 – Test condition . 21
Table C.2 – Exposure time at temperature extremes . 21
Table D.1 – Qualification inspection . 23
Table D.2 – Quality conformance inspection . 25

– 4 – IEC 61196-13:2023 © IEC 2023
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –

Part 13: Sectional specification for semi-rigid cables
with silicon dioxide dielectric

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO)
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.