Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity tests

Is applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only. Lays down test severity levels, test equipment, test set-up, test procedure, criteria for acceptance, etc. This new edition is based on IEC 61000-4-18 and includes changes in the test equipment and test procedures.

Relais de mesure et dispositifs de protection - Partie 22-1: Essais d'influence électrique - Essais d'immunité à l'onde oscillatoire amortie 1 MHz

Est applicable aux relais de mesure et dispositifs de protection à l'état neuf et tous les essais spécifiés sont uniquement des essais de type. Définit les classes de sévérité pour les essais, les matériels d'essai, l'installation d'essai, la procédure d'essai, les critères d'acceptation, etc. Cette nouvelle édition est basée sur la CEI 61000-4-18 et présente des modifications par rapport aux matériels et procédures d'essai.

General Information

Status
Replaced
Publication Date
08-Oct-2007
Current Stage
DELPUB - Deleted Publication
Completion Date
24-May-2013
Ref Project

Relations

Buy Standard

Standard
IEC 60255-22-1:2007 - Measuring relays and protection equipment - Part 22-1: Electrical disturbance tests - 1 MHz burst immunity tests Released:10/9/2007 Isbn:2831893313
English and French language
25 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC 60255-22-1
Edition 3.0 2007-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Measuring relays and protection equipment –
Part 22-1: Electrical disturbance tests – 1 MHz burst immunity tests

Relais de mesure et dispositifs de protection –
Partie 22-1: Essais d’influence électrique – Essais d’immunité à l’onde
oscillatoire amortie 1 MHz
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60255-22-1
Edition 3.0 2007-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Measuring relays and protection equipment –
Part 22-1: Electrical disturbance tests – 1 MHz burst immunity tests

Relais de mesure et dispositifs de protection –
Partie 22-1: Essais d’influence électrique – Essais d’immunité à l’onde
oscillatoire amortie 1 MHz
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
M
CODE PRIX
ICS 29.120.70 ISBN 2-8318-9331-3

– 2 – 60255-22-1 © IEC:2007
CONTENTS
FOREWORD.3

1 Scope and object .5
2 Normative references.5
3 Terms and definitions .5
4 Test severity levels .7
5 Test equipment.7
6 Test set-up .10
7 Test procedure .11
8 Criteria for acceptance.12
9 Test report.13

Figure 1 – Ports for measuring relays and protection equipment .7
Figure 2 – Common mode test between each independent port and earth .8
Figure 3 – Common mode test between each independent port and all other
independent ports coupled to earth.9
Figure 4 – Differential mode test.10
Figure 5 – Test set-up for communication ports with shielded and unshielded cables .12

Table 1 – Test voltages for the EUT ports.7
Table 2 – Criteria for acceptance.12

60255-22-1 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MEASURING RELAYS AND PROTECTION EQUIPMENT –

Part 22-1: Electrical disturbance tests –
1 MHz burst immunity tests
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60255-22-1 has been prepared by IEC technical committee 95:
Measuring relays and protection equipment.
This third edition cancels and replaces the second edition published in 2005. This standard
constitutes a technical revision. The main differences with respect to the previous edition are:
– this document is based on IEC 61000-4-18;
– a capacitor was added for testing shielded communication lines when earthed at one end
only;
– the test procedure for communication ports is clarified;
– the length of the communication cable for testing is fixed at 10 m;
– connection to earth removed in Figure 4 for test generator terminal.

– 4 – 60255-22-1 © IEC:2007
The text of this standard is based on the following documents:
CDV Report on voting
95/204/CDV 95/218/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
A list of all parts of the IEC 60255 series, under the general title Measuring relays and
protection equipment, can be found on the IEC website.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
60255-22-1 © IEC:2007 – 5 –
MEASURING RELAYS AND PROTECTION EQUIPMENT –

Part 22-1: Electrical disturbance tests –
1 MHz burst immunity tests
1 Scope and object
This part of IEC 60255 is based on IEC 61000-4-18, referring to that publication where
applicable, and specifies the general requirements for 1 MHz oscillatory wave immunity tests
for measuring relays and protection equipment for power system protection, including the
control, monitoring and process interface equipment used with the relays and protection
equipment.
The objective of the tests is to confirm that the equipment under test will operate correctly
when energised and subjected to repetitive damped oscillatory waves such as those originating
from closing or opening circuit breakers or disconnectors in high voltage substations or power
plants.
The requirements specified in this standard are applicable to measuring relays and protection
equipment in a new condition and all tests specified are type tests only.
The object of this standard is to state:
– definition of terms used;
– test severity levels;
– test equipment;
– test set-up;
– test procedure;
– criteria for acceptance;
– test report.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the referenced document (including any amendments) applies.
IEC 60255-6, Electrical relays – Part 6: Measuring relays and protection equipment
IEC 61000-4-18:2006, Electromagnetic Compatibility (EMC) – Part 4-18: Testing and
measurement techniques – Damped oscillatory wave immunity test
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

– 6 – 60255-22-1 © IEC:2007
3.1
auxiliary equipment
equipment necessary to provide the EUT with the signals required for normal operation and
equipment to verify the performance of the EUT
3.2
auxiliary power supply port
AC or DC auxiliary energising input of the EUT
3.3
burst
a sequence of a limited number of distinct pulses or an
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.