IEC 61019-1:2004

Surface acoustic wave (SAW) resonators - Part 1: Generic specification

IEC 61019-1:2004 specifies the methods of test and general requirements for SAW resonators using either capability approval or qualification approval procedures of the IECQ system. This first edition of IEC 61019-1 cancels and replaces the first edition of IEC 61019-1-1 published in 1990 and the first edition of IEC 61019-1-2 published in 1993. It constitutes a technical revision.

Résonateurs à ondes acoustiques de surface (OAS) - Partie 1: Spécification générique

La CEI 61019-1:2004 spécifie les méthodes d'essai et les exigences générales pour les résonateurs à OAS utilisant soit les procédures d'agrément de savoir-faire, soit les procédures d'homologation du système IECQ. Cette première édition de la CEI 61019-1 annule et remplace la première édition de la CEI 61019-1-1 publiée en 1990 et la première édition de la CEI 61019-1-2 publiée en 1993. Elle constitue une révision technique.

General Information

• Status: Published
• Publication Date: 01-Nov-2004
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 31.140 - Piezoelectric devices
• Technical Committee: TC 49 - Piezoelectric, dielectric and electrostatic devices and associated materials for frequency control, selection and detection
• Drafting Committee: WG 10 - TC 49/WG 10
• Current Stage: PPUB - Publication issued
• Start Date: 28-Feb-2005
• Completion Date: 02-Nov-2004

Standards Content (Sample)

INTERNATIONAL IEC
STANDARD 61019-1
First edition
2004-11
Surface acoustic wave (SAW) resonators –
Part 1:
Generic specification
Reference number
Publication numbering
As from 1 January 1997 all IEC publications are issued with a designation in the
60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1.
Consolidated editions
The IEC is now publishing consolidated versions of its publications. For example,
edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the
base publication incorporating amendment 1 and the base publication incorporating
amendments 1 and 2.
Further information on IEC publications
The technical content of IEC publications is kept under constant review by the IEC,
thus ensuring that the content reflects current technology. Information relating to
this publication, including its validity, is available in the IEC Catalogue of
publications (see below) in addition to new editions, amendments and corrigenda.
Information on the subjects under consideration and work in progress undertaken
by the technical committee which has prepared this publication, as well as the list
of publications issued, is also available from the following:
• IEC Web Site (www.iec.ch)
• Catalogue of IEC publications
The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to
search by a variety of criteria including text searches, technical committees
and date of publication. On-line information is also available on recently issued
publications, withdrawn and replaced publications, as well as corrigenda.
• IEC Just Published
This summary of recently issued publications (www.iec.ch/online_news/ justpub)
is also available by email. Please contact the Customer Service Centre (see
below) for further information.
• Customer Service Centre
If you have any questions regarding this publication or need further assistance,
please contact the Customer Service Centre:

Email: [e-mail]
Tel: [phone]
Fax: [phone]
INTERNATIONAL IEC
STANDARD 61019-1
First edition
2004-11
Surface acoustic wave (SAW) resonators –
Part 1:
Generic specification
 IEC 2004  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale W
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – 61019-1  IEC:2004(E)
CONTENTS
FOREWORD.4

1 Scope.6
2 Normative references .6
3 Order of precedence.8
4 Terms and definitions .8
4.1 General terms .8
4.2 Operational properties.11
5 Preferred values for ratings and characteristics .19
5.1 Standard nominal frequency values in megahertz (MHz) .19
5.2 Standard operating temperature ranges in degrees Celsius (°C) .19
5.3 Standard values of load capacitance in picofarads (pF).19
5.4 Standard levels of drive in milliwatts (mW) .19
5.5 Standard values of minimum insertion attenuation in decibels (dB).19
5.6 Standard climatic category .20
5.7 Bump severity .20
5.8 Vibration severity .20
5.9 Shock severity.20
5.10 Fine leak rate .21
6 Marking .21
6.1 Resonator marking .21
6.2 Package marking.21
7 Quality assessment procedures.21
7.1 Primary stage of manufacture.21
7.2 Structurally similar components.21
7.3 Subcontracting .22
7.4 Incorporated components .22
7.5 Manufacturer’s approval .22
7.6 Approval procedures .22
7.7 Procedures for capability approval .23
7.8 Procedures for qualification approval.23
7.9 Test procedures .24
7.10 Screening requirements .24
7.11 Rework and repair work.24
7.12 Certified records of released lots.24
7.13 Validity of release.24
7.14 Release for delivery .24
7.15 Unchecked parameters.24
8 Test and measurement procedures.24
8.1 General .24
8.2 Test and measurement conditions .25
8.3 Visual inspection .26

61019-1  IEC:2004(E) – 3 –
8.4 Dimensions and gauging procedures .26
8.5 Measurement method of one-port resonator .26
8.6 Measurement method of two-port resonator.28
8.7 Mechanical and environmental test procedures .32
8.8 Endurance test procedure .37

Figure 1 – Basic configurations of SAW resonators.9
Figure 2 – One-port resonator equivalent circuit .12
Figure 3 – Vector admittance diagram of a one-port SAW resonator .14
Figure 4 – Typical frequency characteristics of a one-port SAW resonator inserted into
a transmission line in series (see 4.2.10.2.1 and 4.2.10.3.1).14
Figure 5 – Resonance and anti-resonance frequencies .15
Figure 6 – Two-port resonator equivalent circuits.17
Figure 7 – Typical frequency characteristics of a two-port resonator .18
Figure 8 – Reflection measurement .27
Figure 9 – Transmission measurement .29

– 4 – 61019-1  IEC:2004(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
SURFACE ACOUSTIC WAVE (SAW) RESONATORS –

Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61019-1 has been prepared by IEC technical committee 49:
Piezoelectric and dielectric devices for frequency control and selection.
This first edition of IEC 61019-1 cancels and replaces the first edition of IEC 61019-1-1
published in 1990 and the first edition of IEC 61019-1-2 published in 1993. It constitutes a
technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
49/689FDIS 49/698/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO IEC Directives, Part 2.

61019-1  IEC:2004(E) – 5 –
IEC 61019 consists of the following parts under the general title Surface acoustic wave (SAW)
resonators:
Part 1: Generic specification
Part 2: Guide to the use (at present under revision)
Part 3: Standard outlines and lead connections

The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

– 6 – 61019-1  IEC:2004(E)
SURFACE ACOUSTIC WAVE (SAW) RESONATORS –

Part 1: Generic specification
1 Scope
This part of IEC 61019 specifies the methods of test and general requirements for SAW
resonators using either capability approval or qualification approval procedures of the IECQ
system.
2 Normative references
The following referenced documents are indispensable f
...

IEC 61019-1 ®
Edition 1.0 2004-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Surface acoustic wave (SAW) resonators –
Part 1: Generic specification
Résonateurs à ondes acoustiques de surface (OAS) –
Partie 1: Spécification générique

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
 Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
 IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
 Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
 Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
 Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
 Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
 Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
 Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: [e-mail]
Tél.: [phone]
Fax: [phone]
IEC 61019-1 ®
Edition 1.0 2004-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Surface acoustic wave (SAW) resonators –
Part 1: Generic specification
Résonateurs à ondes acoustiques de surface (OAS) –
Partie 1: Spécification générique

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX W
ICS 31.140 ISBN 978-2-88912-596-8

– 2 – 61019-1  IEC:2004
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Order of precedence . 8
4 Terms and definitions . 8
4.1 General terms . 8
4.2 Operational properties . 11
5 Preferred values for ratings and characteristics . 19
5.1 Standard nominal frequency values in megahertz (MHz) . 19
5.2 Standard operating temperature ranges in degrees Celsius (°C) . 19
5.3 Standard values of load capacitance in picofarads (pF) . 19
5.4 Standard levels of drive in milliwatts (mW) . 19
5.5 Standard values of minimum insertion attenuation in decibels (dB) . 19
5.6 Standard climatic category . 20
5.7 Bump severity . 20
5.8 Vibration severity . 20
5.9 Shock severity . 20
5.10 Fine leak rate . 21
6 Marking . 21
6.1 Resonator marking . 21
6.2 Package marking . 21
7 Quality assessment procedures . 21
7.1 Primary stage of manufacture . 21
7.2 Structurally similar components . 21
7.3 Subcontracting . 22
7.4 Incorporated components . 22
7.5 Manufacturer’s approval . 22
7.6 Approval procedures . 22
7.7 Procedures for capability approval . 23
7.8 Procedures for qualification approval . 23
7.9 Test procedures . 24
7.10 Screening requirements . 24
7.11 Rework and repair work . 24
7.12 Certified records of released lots . 24
7.13 Validity of release . 24
7.14 Release for delivery . 24
7.15 Unchecked parameters . 24
8 Test and measurement procedures . 24
8.1 General . 24
8.2 Test and measurement conditions . 25
8.3 Visual inspection . 26
8.4 Dimensions and gauging procedures . 26
8.5 Measurement method of one-port resonator . 26
8.6 Measurement method of two-port resonator . 28
8.7 Mechanical and environmental test procedures . 32

61019-1  IEC:2004 – 3 –
8.8 Endurance test procedure . 37

Figure 1 – Basic configurations of SAW resonators . 9
Figure 2 – One-port resonator equivalent circuit . 12
Figure 3 – Vector admittance diagram of a one-port SAW resonator . 14
Figure 4 – Typical frequency characteristics of a one-port SAW resonator inserted into
a transmission line in series (see 4.2.10.2.1 and 4.2.10.3.1) . 14
Figure 5 – Resonance and anti-resonance frequencies . 15
Figure 6 – Two-port resonator equivalent circuits . 17
Figure 7 – Typical frequency characteristics of a two-port resonator . 18
Figure 8 – Reflection measurement . 27
Figure 9 – Transmission measurement . 29

– 4 – 61019-1  IEC:2004
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
SURFACE ACOUSTIC WAVE (SAW) RESONATORS –

Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical com
...