IEC TS 62312-2:2018
(Main)Guideline for synchronization of audio and video - Part 2: Methods for synchronization of audio and video systems
Guideline for synchronization of audio and video - Part 2: Methods for synchronization of audio and video systems
IEC TS 62312-2:2018 gives guidelines for methods of synchronization of audio and video. It describes the system model and general methods for the synchronization of audio and video. The methods exclude the synchronization of the signal source and the spatial delay of audio reproduction. IEC TS 62312-2:2018 cancels and replaces the first edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) fingerprint is newly introduced;
b) addition of the synchronization information from fingerprint (SMPTE spec.);
c) addition of the method for using the above information.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC TS 62312-2 ®
Edition 2.0 2018-11
TECHNICAL
SPECIFICATION
Guideline for synchronization of audio and video –
Part 2: Methods for synchronization of audio and video systems
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 62312-2 ®
Edition 2.0 2018-11
TECHNICAL
SPECIFICATION
Guideline for synchronization of audio and video –
Part 2: Methods for synchronization of audio and video systems
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.160.01 ISBN 978-2-8322-6188-0
– 2 – IEC TS 62312-2:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 System model . 7
4.1 Audio and video system . 7
4.2 System model . 7
4.3 Audio and video device . 7
4.4 Controller . 9
4.5 Source device and display device . 9
4.6 Controller function of audio and video device . 10
5 Methods for synchronization . 11
5.1 Information for synchronization . 11
5.1.1 Time-code information . 11
5.1.2 Latency information . 11
5.1.3 Synchronization information . 11
5.2 Methods for synchronization . 12
5.2.1 General . 12
5.2.2 Method with time-code information . 13
5.2.3 Method with latency information . 14
5.2.4 Method with synchronization information . 14
5.3 Method with IEC 60958-3 . 14
5.4 Method with IEC 61883-6 . 14
5.5 Method with other interface specifications . 15
Annex A (informative) Information for synchronization . 16
A.1 Time-code information . 16
A.2 Latency information . 16
A.3 Synchronization information . 16
Bibliography . 17
Figure 1 – System model . 7
Figure 2 – Audio and video device . 8
Figure 3 – Information and control in audio and video device . 9
Figure 4 – Source device . 10
Figure 5 – Display device . 10
Figure 6 – Audio amplifier . 10
Figure 7 – Controller function of audio and video device . 11
Figure 8 – Additional delay . 12
Figure 9 – Multiple reproductions . 13
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
GUIDELINE FOR SYNCHRONIZATION OF AUDIO AND VIDEO –
Part 2: Methods for synchronization of audio and video systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. In
exceptional circumstances, a technical committee may propose the publication of a Technical
Specification when
• the required support cannot be obtained for the publication of an International Standard,
despite repeated efforts, or
• the subject is still under technical development or where, for any other reason, there is the
future but no immediate possibility of an agreement on an International Standard.
Technical Specifications are subject to review within three years of publication to decide
whether they can be transformed into International Standards.
IEC 62312-2, which is a technical specification, has been prepared by technical area 11:
Quality for audio, video and multimedia systems, of IEC technical committee 100: Audio,
video and multimedia systems and equipment.
– 4 – IEC TS 62312-2:2018 © IEC 2018
This second edition cancels and replaces the first edition published in 2007. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) fingerprint is newly introduced;
b) addition of the synchronization information from fingerprint (SMPTE spec.);
c) addition of the method for using the above information.
The text of this Technical Specification is based on the following documents:
Draft TS Report on voting
100/3049/DTS 100/3106/RVDTS
Full information on the voting for the approval of this Technical Specification can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The list of all the parts of IEC 62312, published under the general title Guideline for
synchronization of audio and video, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• transformed into an International standard,
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
INTRODUCTION
Audio, video and multimedia systems and equipment have begun to use digital technologies.
Digital systems or equipment may cause delay of audio and video signals because digital
signal processing causes latency and delay. The unevenness of the delay between audio and
video can cause synchronization problems.
For instance, a digital broadcasting system uses signal compression of audio and video. A
receiver has signal decoders, and this can cause unevenness of the delay between audio and
...
IEC TS 62312-2 ®
Edition 2.0 2018-11
REDLINE VERSION
TECHNICAL
SPECIFICATION
colour
inside
Guideline for synchronization of audio and video –
Part 2: Methods for synchronization of audio and video systems
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 62312-2 ®
Edition 2.0 2018-11
REDLINE VERSION
TECHNICAL
SPECIFICATION
colour
inside
Guideline for synchronization of audio and video –
Part 2: Methods for synchronization of audio and video systems
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.160.01 ISBN 978-2-8322-6219-1
– 2 – IEC TS 62312-2:2018 RLV © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 2
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 System model . 7
4.1 Audio and video system . 7
Latency and delay .
4.2 System model . 7
4.3 Audio and video device . 8
4.4 Controller . 9
4.5 Source device and display device . 9
4.6 Controller function of audio and video device . 10
5 Methods for synchronization . 11
5.1 Information for synchronization . 11
5.1.1 Time-code information . 11
5.1.2 Latency information . 11
5.1.3 Synchronization information . 11
5.2 Methods for synchronization . 12
5.2.1 General . 12
5.2.2 Method with time-code information . 13
5.2.3 Method with latency information . 14
5.2.4 Method with synchronization information . 14
5.3 Method with IEC 60958-3 . 14
5.4 Method with IEC 61883-6 . 14
5.5 Method with other interface specifications . 15
Annex A (informative) Information for synchronization . 16
A.1 Time-code information . 16
A.2 Latency information . 16
A.3 Synchronization information . 16
Bibliography . 17
Figure 1 – System model . 7
Figure 2 – Audio and video device . 8
Figure 3 – Information and control in audio and video device . 9
Figure 4 – Source device . 10
Figure 5 – Display device . 10
Figure 6 – Audio amplifier . 10
Figure 7 – Controller function of audio and video device . 11
Figure 8 – Additional delay . 12
Figure 9 – Multiple reproductions . 13
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
GUIDELINE FOR SYNCHRONIZATION OF AUDIO AND VIDEO –
Part 2: Methods for synchronization of audio and video systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This redline version of the official IEC Standard allows the user to identify the changes
made to the previous edition. A vertical bar appears in the margin wherever a change
has been made. Additions are in green text, deletions are in strikethrough red text.
– 4 – IEC TS 62312-2:2018 RLV © IEC 2018
The main task of IEC technical committees is to prepare International Standards. In
exceptional circumstances, a technical committee may propose the publication of a Technical
Specification when
• the required support cannot be obtained for the publication of an International Standard,
despite repeated efforts, or
• the subject is still under technical development or where, for any other reason, there is the
future but no immediate possibility of an agreement on an International Standard.
Technical Specifications are subject to review within three years of publication to decide
whether they can be transformed into International Standards.
IEC 62312-2, which is a technical specification, has been prepared by technical area 11:
Quality for audio, video and multimedia systems, of IEC technical committee 100: Audio,
video and multimedia systems and equipment.
This second edition cancels and replaces the first edition published in 2007. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) fingerprint is newly introduced;
b) addition of the synchronization information from fingerprint (SMPTE spec.);
c) addition of the method for using the above information.
The text of this Technical Specification is based on the following documents:
Draft TS Report on voting
100/3049/DTS 100/3106/RVDTS
Full information on the voting for the approval of this Technical Specification can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The list of all the parts of IEC 62312, published under the general title Guideline for
synchronization of audio and video, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• transformed into an International standard,
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users shoul
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.