IEC 62552-3:2015/AMD1:2020

Amendment 1 - Household refrigerating appliances - Characteristics and test methods - Part 3: Energy consumption and volume

Amendement 1 - Appareils de réfrigération à usage ménager - Caractéristiques et méthodes d'essai - Partie 3: Consommation d'énergie et volume

General Information

• Status: Published
• Publication Date: 29-Nov-2020
• ICS: 97.030 - Domestic electrical appliances in general
• Technical Committee: SC 59M - Performance of electrical household and similar cooling and freezing appliances
• Drafting Committee: MT 2 - TC 59/SC 59M/MT 2
• Current Stage: PPUB - Publication issued
• Start Date: 11-Dec-2020
• Completion Date: 30-Nov-2020

Relations

• Amends: IEC 62552-3:2015 - Household refrigerating appliances - Characteristics and test methods - Part 3: Energy consumption and volume
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 62552-3 ®
Edition 1.0 2020-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Household refrigerating appliances – Characteristics and test methods –
Part 3: Energy consumption and volume

Appareils de réfrigération à usage ménager – Caractéristiques et méthodes
d'essai –
Partie 3: Consommation d'énergie et volume

IEC 62552-3:2015-02/AMD1:2020-11(en-fr)

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: [phone]
3, rue de Varembé [e-mail]
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and definitions clause of
IEC publications issued between 2002 and 2015. Some
IEC Customer Service Centre - webstore.iec.ch/csc entries have been collected from earlier publications of IEC
If you wish to give us your feedback on this publication or TC 37, 77, 86 and CISPR.

need further assistance, please contact the Customer Service

Centre: [e-mail].
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Recherche de publications IEC - Electropedia - www.electropedia.org
webstore.iec.ch/advsearchform Le premier dictionnaire d'électrotechnologie en ligne au
La recherche avancée permet de trouver des publications IEC monde, avec plus de 22 000 articles terminologiques en
en utilisant différents critères (numéro de référence, texte, anglais et en français, ainsi que les termes équivalents dans
comité d’études,…). Elle donne aussi des informations sur les 16 langues additionnelles. Egalement appelé Vocabulaire
projets et les publications remplacées ou retirées. Electrotechnique International (IEV) en ligne.

IEC Just Published - webstore.iec.ch/justpublished Glossaire IEC - std.iec.ch/glossary
Restez informé sur les nouvelles publications IEC. Just 67 000 entrées terminologiques électrotechniques, en anglais
Published détaille les nouvelles publications parues. et en français, extraites des articles Termes et définitions des
Disponible en ligne et une fois par mois par email. publications IEC parues entre 2002 et 2015. Plus certaines
entrées antérieures extraites des publications des CE 37, 77,
Service Clients - webstore.iec.ch/csc 86 et CISPR de l'IEC.

Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
[e-mail].
IEC 62552-3 ®
Edition 1.0 2020-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Household refrigerating appliances – Characteristics and test methods –

Part 3: Energy consumption and volume

Appareils de réfrigération à usage ménager – Caractéristiques et méthodes

d'essai –
Partie 3: Consommation d'énergie et volume

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 97.030 ISBN 978-2-8322-9068-2

– 2 – IEC 62552-3:2015/AMD1:2020
© IEC 2020
FOREWORD
This amendment has been prepared by subcommittee 59M: Performance of electrical household
and similar cooling and freezing appliances, of IEC technical committee 59: Performance of
household and similar electrical appliances.
The text of this amendment is based on the following documents:
FDIS Report on voting
59M/128/FDIS 59M/134/RVD
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
5.1 General
Replace the NOTE with the following new content:
NOTE Refer to the requirements in Annex B of IEC 62552-1:2015 and IEC 62552-1:2015/AMD1:2020 for variable
temperature compartments. For energy testing, these are operated on the function (continuous temperature
operating range) that uses the most energy.

9 Test report
Replace the existing content with the following new content:
A test report should be prepared that includes all of the relevant information listed in Annex F of
IEC 62552-1:2015/AMD:2020 for tests undertaken in accordance with this document.

© IEC 2020
A.1 General
Replace the fourth paragraph with the following new content:
The refrigerating appliance shall have air temperature sensors installed at the positions
specified in Annex D of IEC 62552-1:2015 and IEC 62552-1:2015/AMD1:2020. The
determination of compartment air temperature during energy testing shall be as specified in
Annex D of IEC 62552-1:2015 and IEC 62552-1:2015/AMD1:2020.

A.2.6.1 General
Replace the fourth paragraph with the following new content:
Where the ice storage space occupies a complete compartment, the temperature sensor
placements shall be in accordance with Annex D of IEC 62552-1:2015 and
IEC 62552-1:2015/AMD1:2020 (not A.2.6.5 of this document).

A.2.6.5 Position of the temperature sensor in automatic icemakers
Replace the first sentence of the first paragraph with the following:
An automatic icemaker bin shall have a single temperature sensor located in the
position specified as follows for all energy tests:

B.4.3 Case SS2 calculation of values
Replace Formula (13) with the following new formula:
ΔTh
dfj−i
TT( )− (13)

SS2−i av−endX−endY−i
(tt− )

end−−Y end X

Replace the definition of ∆Th with:
df-i
∆Th is the accumulated temperature difference over time in each compartment i in Kh
dfj-i
as determined in accordance with C.3.3 for the defrost and recovery period j
commencing at the end of period X
Replace Formula (14) with the following new formula:
Rt −−Rt Δt
end−−Y end X drj
CRt = (14)
SS2
(tt− )
end−−Y end X
Replace the definition ∆t of with:
dr
∆t is the additional compressor run time in h as determined in accordance with C.3.3
drj
for the defrost and recovery period j commencing at the end of period X

=
– 4 – IEC 62552-3:2015/AMD1:2020
© IEC 2020
C.3.3 Case DF1 calculation of values
Add the following new content below the NOTE:
During a load processing efficiency test, it is possible that one or more defrosts occur for
which a correction must be made. This correction is based on splitting the defrost and recovery
energy in a fixed part and the energy used by the defrost heater:
Fixed defrost adder: ∆E = ∆E − E (63)
df-adderj dfj df-heaterj
where:
E is the measured defrost heater energy during the defrost and recovery period j,
df-heaterj
expressed in Wh
NOTE This formula is applied to each valid defrost during steady state. A representative value for the fixed defrost
adder (∆E ) is determined in accordance with Formula (64) and is subsequently used in the evaluation of a load
df-adder
processing test [using Formula (51) or, if multiple defrost systems are present, Formula (65)].
C.4 Number of valid defrost and recovery periods
At the end of the clause, add the following note:
NOTE The defrost heater energy E and incremental defrost and recovery energy ∆E for new appliances and
df-heaterj dfj
appliances that have not been operated for some time may be initially low until the defrost heater energy stabilises.
C.5 Calculation of representative defrost energy and temperature
Replace Formula (22) with the following new formula:
m
ΔE
∑ dfj
j=1
ΔE = F (22)
df df
m
Add the following text below the line ∆E :
dfj
F is a regional scaling factor that can be used to compensate for frost load and usage factor,
df
which impacts the defrost intervals. The default value for F is 1,0.
df
Add the following paragraph above Formula (23):
To correct a load processing efficiency test where one or more defrosts occurs, a
representative value for the fixed defrost adder is defined:
m
ΔE
∑ df−adderj
j=1
ΔE = (64)
df−adder
m
D.2 Elapsed time defrost controllers
Replace NOTE 2 with the following new note:
NOTE 2 The same timers could be used as compressor run time controllers or as elapsed time controllers,
depending on how they are configured in the refrigerating appliance.

© IEC 2020
D.3 Compressor run time defrost controllers
Replace the entire clause with the following:
D.3 Compressor run time defrost controllers
For these controllers, the defrost interval is defined by the compressor run time (or on time in
hours) (or, in some cases, the compressor run time plus the maximum time allocated for defrost
heater operation). These controllers are only applicable to single-speed compressors. The
defrost interval is therefore approximately inversely proportional to the total heat load on the
refrigeration system (ambient temperature and user loads plus any internal heat loads). The
most common defrost run time controllers range from 6 h to 12 h of compressor run time.
Typically, this would result in defrost intervals of the order of 12 h to 30 h (elapsed time) at
elevated ambient temperatures and somewhat longer defrost intervals at lower ambient
temperatures.
NOTE 1 The same timers could be used as compressor run time controllers or as elapsed time controllers,
depending on how they are configured in the refrigerating appliance.
If the run time controller is not accessible (or where it is not clear whether the controller is a run
time controller) or where the laboratory is not able to directly measure the controller operation
and does not know its run time, the value for the proxy run time shall be measured by testing as
set out below. Any routine energy tests or other tests may be used for this purpose.
Each measurement shall be undertaken over a whole defrost control cycle and tests shall be
undertaken in at least two different ambient temperatures in order to verify that it is a run time
controller and to estimate the value of t . The period selected shall comply with the following
prt
requirements:
• the first defrost shall qualify as a valid defrost as specified in Clause C.3;
• the test period shall include at least part of the subsequent defrost and recovery period
that is initiated automatically without any intervention (defrost heater on).
The estimated proxy run time of the compressor run time defrost controller for a given set of
test data that complies with these requirements is given by:
t = t + t (25)
prtj crtj dhj
where
t is the estimated proxy run time of the compressor run time defrost controller for the test
prtj
period starting with defrost and recovery period j in h;
t is the measured compressor run time in h from the initiation of defrost heater operation
crtj
for defrost and recovery period j to the initiation of defrost heater operation for the
subsequent defrost and recovery period j + 1;
is the time from the start of the defrost heater on until the compressor restarts, in h,
t
dhj
during defrost and recovery period j where the timer advances during the heater
operation; otherwise, a value of zero if the timer does not advance during the heater
operation.
NOTE 2 A common configuration is that the defrost heater is allocated a fixed maximum time of operation in the
timer defrost controller (say 20 min). Th
...