IEC 61196-5:2022
(Main)Coaxial communication cables - Part 5: Sectional specification for CATV trunk and distribution cables
Coaxial communication cables - Part 5: Sectional specification for CATV trunk and distribution cables
IEC 61196-5:2022, which is a sectional specification, applies to coaxial cables for analogue and digital one- and two-way signal transmission, for example for cable networks for television signals, sound signals and interactive services in accordance with IEC 60728-1, IEC 60728-1-1, IEC 60728-101, IEC 60728-10, ISO/IEC 11801-1 and ISO/IEC 11801-4. This includes also the transmission of BCT signals provided by a CATV, MATV or SMATV cable networks.
This document specifies the test procedures and requirements for trunk and distribution cables for temperatures between −40 °C and +65 °C and in the frequency range of 5 MHz to 2 000 MHz.
This fourth edition cancels and replaces the third edition published in 2018. This edition includes the following significant technical changes with respect to the previous edition:
a. complete revision; b. cable identification and marking has been added; c. Table B.1, cable types have been added.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61196-5 ®
Edition 4.0 2022-12
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 5: Sectional specification for CATV trunk and distribution cables
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 19 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 61196-5 ®
Edition 4.0 2022-12
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 5: Sectional specification for CATV trunk and distribution cables
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-6147-7
– 2 – IEC 61196-5:2022 © IEC 2022
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 8
4 Materials and cable construction . 8
4.1 Cable construction . 8
4.2 Inner conductor . 8
4.2.1 Conductor material . 8
4.2.2 Conductor construction . 8
4.3 Dielectric . 9
4.4 Outer conductor or screen . 9
4.5 Filling compounds . 9
4.6 Moisture barriers . 9
4.7 Wrapping layers . 9
4.8 Sheath . 9
4.9 Metallic protection . 10
4.10 Cable integral suspension strand (messenger wire) . 10
4.11 Oversheath . 10
4.12 Fauna proofing . 10
4.13 Chemical and/or environmental proofing . 10
4.14 Cable identification . 10
4.14.1 General . 10
4.14.2 Sheath marking . 10
4.14.3 Labelling . 11
4.15 Completed cable . 11
4.16 Standard ratings and characteristics . 11
5 Tests for completed cables . 11
5.1 General . 11
5.2 Electrical testing of the finished cable . 11
5.2.1 Low-frequency and DC electrical measurements . 11
5.2.2 High-frequency electrical and transmission test procedures and
requirements . 12
5.3 Environmental test procedures and requirements of the finished cable . 14
5.4 Test procedures and requirements of mechanical characteristics of the
finished cable. 14
5.5 Fire performance . 15
6 Quality assessment . 16
7 Delivery and storage . 16
Annex A (normative) Cable identification and marking . 17
A.1 Cable identification . 17
A.1.1 Type name . 17
A.1.2 Variants . 17
A.1.3 Screening classes . 18
A.2 Cable marking . 18
Annex B (informative) Cable types . 19
Table 1 – Low-frequency and DC test procedures and requirements . 12
Table 2 – High-frequency electrical and transmission test procedures and requirements . 13
Table 3 – Environmental test procedures and requirements of the finished cable . 14
Table 4 – Test procedures and requirements of mechanical characteristics of the
finished cable . 15
Table 5 – Fire performance requirements . 16
Table B.1 – Distribution and trunk cables – Preferred nominal dimensions and ratings . 19
– 4 – IEC 61196-5:2022 © IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –
Part 5: Sectional specification for CATV trunk
and distribution cables
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61196-5 has been prepared by subcommittee 46A: Coaxial cables, of IEC technical
committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive
components and accessories. It is an International Standard.
This fourth edition cancels and replaces the third edition published in 2018. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Clause 4: complete revision;
b) Annex A: cable identification and marking has been added;
c) Annex B: Table B.1, cable types have been added.
The text of this International Standard is based on the following documents:
Draft Report on voting
46A/1605/FDIS 46A/1610/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
A list of all parts in the IEC 61196 series, published under the general title Coaxial
communication cables, can be found on the IEC website.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
– 6 – IEC 611
...
IEC 61196-5 ®
Edition 4.0 2022-12
COMMENTED VERSION
INTERNATIONAL
STANDARD
colour
inside
Coaxial communication cables –
Part 5: Sectional specification for CATV trunk and distribution cables
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a
Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 19 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 61196-5 ®
Edition 4.0 2022-12
COMMENTED VERSION
INTERNATIONAL
STANDARD
colour
inside
Coaxial communication cables –
Part 5: Sectional specification for CATV trunk and distribution cables
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-6309-9
– 2 – IEC 61196-5:2022 CMV © IEC 2022
CONTENTS
FOREWORD .4
1 Scope .6
2 Normative references .6
3 Terms and definitions .8
4 Materials and cable construction.8
4.1 Cable construction .8
4.2 Inner conductor .8
4.2.1 Conductor material .8
4.2.2 Conductor construction .8
4.3 Dielectric .9
4.4 Outer conductor or screen .9
4.5 Filling compounds .9
4.6 Moisture barriers .9
4.7 Wrapping layers .9
4.8 Sheath .9
4.9 Metallic protection . 10
4.10 Cable integral suspension strand (messenger wire) . 10
4.11 Oversheath. 10
4.12 Fauna proofing . 10
4.13 Chemical and/or environmental proofing . 10
4.14 Cable identification . 10
4.14.1 General . 10
4.14.2 Sheath marking . 10
4.14.3 Labelling . 11
4.15 Completed cable . 11
4.16 Standard ratings and characteristics. 11
6 Identification and marking .
6.1 Cable identification .
6.2 Cable marking .
6.3 Labelling .
5 Tests for completed cables . 11
5.1 General . 11
5.2 Electrical testing of the finished cable . 12
5.2.1 Low-frequency and DC electrical measurements . 12
5.2.2 High-frequency electrical and transmission test procedures and
requirements . 12
5.3 Environmental test procedures and requirements of the finished cable . 14
5.4 Test procedures and requirements of mechanical characteristics of the
finished cable . 14
5.5 Fire performance . 15
6 Quality assessment . 16
7 Delivery and storage . 16
Annex A (normative) Cable identification and marking . 17
A.1 Cable identification . 17
A.1.1 Type name . 17
A.1.2 Variants . 17
A.1.3 Screening classes . 18
A.2 Cable marking . 18
Annex B (informative) Cable types . 19
List of comments . 20
Table 1 – Low-frequency and DC test procedures and requirements . 12
Table 2 – High-frequency electrical and transmission test procedures and requirements . 13
Table 3 – Environmental test procedures and requirements of the finished cable. 14
Table 4 – Test procedures and requirements of mechanical characteristics of the
finished cable. 15
Table 5 – Fire performance requirements . 16
Table B.1 – Distribution and trunk cables – Preferred nominal dimensions and ratings . 19
– 4 – IEC 61196-5:2022 CMV © IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –
Part 5: Sectional specification for CATV trunk
and distribution cables
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
This commented version (CMV) of the official standard IEC 61196-5:2022 edition 4.0
allows the user to identify the changes made to the previous IEC 61196-5:2018 edition
3.0. Furthermore, comments from IEC SC 46A experts are provided to explain the reasons
of the most relevant changes, or to clarify any part of the content.
A vertical bar appears in the margin wherever a change has been made. Additions are in
green text, deletions are in strikethrough red text. Experts' comments are identified by a
blue-background number. Mouse over a number to display a pop-up note with the
comment.
This publication contains the CMV and the official standard. The full list of comments is
available at the end of the CMV.
IEC 61196-5 has been prepared by subcommittee 46A: Coaxial cables, of IEC technical
committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive
components and accessories. It is an International Standard.
This fourth edition cancels and replaces the third edition published in 2018. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Clause 4: complete revision;
b) Annex A: cable identification and marking has been added;
c) Annex B: Table B.1, cable types have been added.
The t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.