IEC PAS 60127-8:2014

Miniature fuses - Part 8: Fuse resistors with particular overcurrent protection

IEC/PAS 60127-8:2014(E) relates to fuse resistors with particular overcurrent protection rated up to 500 V a.c. and/or 500 V d.c. for printed circuits and other substrate systems, used for the protection of electric appliances, electronic equipment and component parts thereof, normally intended to be used indoors. It does not apply to fuse resistors with particular overcurrent protection for appliances intended to be used under special conditions, such as in a corrosive or explosive atmosphere. The object of this PAS is:
- to establish uniform requirements for fuse resistors with particular overcurrent protection so as to protect appliances or parts of appliances in the most suitable way;
- to define the performance of the fuse resistors with particular overcurrent protection, so as to give guidance to manufacturers of electrical appliances and electronic equipment and to ensure replacement of fuse resistors with particular overcurrent protection by those of similar dimensions and characteristics;
- to define methods of testing. This PAS applies in addition to the requirements of IEC 60127-1. Keywords: resistors with particular overcurrent protection, protection of electric appliances, electronic equipment and component parts

General Information

• Status: Replaced
• Publication Date: 15-Dec-2014
• ICS: 29.120.50 - Fuses and other overcurrent protection devices
• Technical Committee: SC 32C - Miniature fuses
• Current Stage: DELPUB - Deleted Publication
• Completion Date: 26-Jun-2018

Relations

• Revised: IEC 60127-8:2018 - Miniature fuses - Part 8: Fuse resistors with particular overcurrent protection
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC PAS 60127-8 ®
Edition 1.0 2014-12
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
Miniature fuses –
Part 8: Fuse resistors with particular overcurrent protection

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]

CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing more than 30 000 terms and
Technical Specifications, Technical Reports and other definitions in English and French, with equivalent terms in 14
documents. Available for PC, Mac OS, Android Tablets and additional languages. Also known as the International
iPad. Electrotechnical Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a More than 55 000 electrotechnical terminology entries in
variety of criteria (reference number, text, technical English and French extracted from the Terms and Definitions
committee,…). It also gives information on projects, replaced clause of IEC publications issued since 2002. Some entries
and withdrawn publications. have been collected from earlier publications of IEC TC 37,

77, 86 and CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC PAS 60127-8 ®
Edition 1.0 2014-12
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
Miniature fuses –
Part 8: Fuse resistors with particular overcurrent protection

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
T
ICS 29.120.50 ISBN 978-2-8322-1982-9

– 2 – IEC PAS 60127-8:2014 © IEC 2014

CONTENTS
FOREWORD . 4

INTRODUCTION . 6

1 Scope . 7

2 Normative references . 7

3 Terms and definitions . 8

4 General requirements . 10

5 Standard ratings . 10
6 Marking . 10
7 General notes on tests . 11
7.1 Atmospheric conditions for testing . 11
7.2 Type tests . 11
7.3 Fuse-bases for tests . 12
7.3.1 General requirements . 12
7.3.2 Through-hole mounting of fuse resistors with particular overcurrent
protection . 12
7.3.3 Surface mounting of fuse resistors with particular overcurrent protection . 12
7.4 Nature of supply . 12
8 Dimensions and construction . 12
8.1 Dimensions . 12
8.1.1 Creepage distances and clearances . 13
8.2 Construction . 13
8.3 Terminations . 14
8.3.1 Through-hole mount fuse resistors with particular overcurrent protection . 14
8.3.2 Surface mount fuse resistors with particular overcurrent protection . 14
8.4 Alignment and configuration of terminations . 14
8.5 Soldered joints . 15
8.6 Solderability of terminations . 15
8.7 Resistance to soldering heat . 15
9 Electrical requirements . 15
9.1 Resistance value . 15
9.2 Functioning characteristic at the minimum breaking dissipation. 15

9.2.1 Functioning characteristic at an ambient temperature of 70 °C . 15
9.2.2 Test at elevated temperature . 16
9.2.3 Test procedure . 16
9.2.4 Presentation of results . 16
9.3 Rated breaking capacity. 16
9.3.2 Criteria for satisfactory performance . 17
9.3.3 Insulation resistance . 17
9.4 Endurance tests . 17
9.5 Maximum sustained dissipation . 18
9.6 Pulse tests . 18
9.7 Temperature of fuse resistors with particular overcurrent protection. 18
9.8 Operating overvoltage . 18
Bibliography . 25

Figure 1 – Test board for through-hole mount fuse resistors with particular overcurrent

protection . 20

Figure 2 – Test board for surface mount fuse resistors with particular overcurrent

protection . 21

Figure 3 – Test fuse-base . 22

Figure 4 – Bending jig for surface mount fuse resistors with particular overcurrent

protection . 23

Figure 5 – Test circuit for the tests according to 9.3 . 24

Table 1 – Creepage distances and clearances (absolute minimum values) . 13
Table 2 – Test voltages for dielectric strength . 17
Table 3 – Testing schedule for individual dissipation ratings . 19

– 4 – IEC PAS 60127-8:2014 © IEC 2014

INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________
MINIATURE FUSES –
Part 8: Fuse resistors with particular overcurrent protection

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

A PAS is a technical specification not fulfilling the requirements for a standard, but made
available to the public.
IEC PAS 60127-8 has been processed by subcommittee 32C: Miniature fuses, of IEC
technical committee 32: Fuses.
The text of this PAS is based on the This PAS was approved for
following document: publication by the P-members of the
committee concerned as indicated in
the following document
Draft PAS Report on voting
32C/500/PAS 32C/503/RVD
Following publication of this PAS, which is a pre-standard publication, the technical committee
or subcommittee concerned may transform it into an International Standard.

A list of all parts in the IEC 60127, published under the general title Miniature fuses, can be

found on the IEC website.
This PAS shall remain valid for an initial maximum period of 3 years starting from the

publication date. The validity may be extended for a single period
...