iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC 60255-5

Electrical Relays - Part 5: Insulation coordination for measuring relays and protection equipment - Requirements and tests

Electrical Relays - Part 5: Insulation coordination for measuring relays and protection equipment - Requirements and tests

Lays down general requirements for the insulation coordination of measuring relays and protection equipment. Gives guidance for the selection of clearances and creepage distances and other aspects related to the insulation of measuring relays and protection equipment; specifies requirements for voltage tests and insulation resistance measurement.

Relais électriques - Partie 5: Coordination de l'isolement des relais de mesure et des dispositifs de protection - Prescriptions et essais

Donne des prescriptions générales pour la coordination de l'isolement des relais de mesure et des dispositifs de protection. Fournit les directives pour la sélection des distances d'isolement et des lignes de fuite et d'autres aspects liés à l'isolation des relais de mesure et des dispositifs de protection; donne des prescriptions pour les essais de tension et la mesure de la résistance d'isolement.

Electrical relays - Part 5: Insulation tests for electrical relays

General Information

Status
Not Published
ICS
29.120.70 - Relays
Technical Committee
TC 95 - Measuring relays and protection equipment
Current Stage
PPUB - Publication issued
Start Date
14-Dec-2000
Ref Project
SIST IEC 60255-5:1995 - Electrical Relays - Part 5: Insulation coordination for measuring relays and protection equipment - Requirements and tests

Buy Standard

IEC 60255-5:1995IEC 60255-5:1995
PreviousNext
Standard
IEC 60255-5:1995
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST IEC 60255-5:1995
01-avgust-1995
Electrical relays - Part 5: Insulation tests for electrical relays
Electrical Relays - Part 5: Insulation coordination for measuring relays and protection
equipment - Requirements and tests
Relais électriques - Partie 5: Coordination de l'isolement des relais de mesure et des
dispositifs de protection - Prescriptions et essais
Ta slovenski standard je istoveten z: IEC 60255-5
ICS:
29.120.70 Releji Relays
SIST IEC 60255-5:1995 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST IEC 60255-5:1995

---------------------- Page: 2 ----------------------

SIST IEC 60255-5:1995

---------------------- Page: 3 ----------------------

SIST IEC 60255-5:1995

---------------------- Page: 4 ----------------------

SIST IEC 60255-5:1995

---------------------- Page: 5 ----------------------

SIST IEC 60255-5:1995

---------------------- Page: 6 ----------------------

SIST IEC 60255-5:1995

---------------------- Page: 7 ----------------------

SIS
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC 60255-187-1:2021(Main)
Measuring relays and protection equipment - Part 187-1: Functional requirements for differential protection - Restrained and unrestrained differential protection of motors, generators and transformers

IEC 60255-187-1:2021 specifies the minimum requirements for functional and performance evaluation of (longitudinal) differential protection designed for the detection of faults in ac motors, generators and transformers. This document also defines how to document and publish performance test results. This document defines the influencing factors that affect the accuracy under steady state conditions and performance characteristics during dynamic conditions. The test methodologies for verifying performance characteristics and accuracy are also included in this document.
This document, together with IEC 60255-187-2 and IEC 60255-187-3, cancels and replaces IEC 60255-13. This document includes the following significant technical changes with respect to IEC 60255-13:
a) IEC 60255-13 has been significantly revised to follow the common structure of the functional standards for protection relays (IEC 60255-1xx series). IEC 60255-187-1 has been developed to address the restrained and unrestrained differential protection of motors, generators and transformers. The revisions include detailed description of the functions including the performance specification, testing and documentation requirements.
The contents of the corrigendum of April 2023 have been included in this copy.

  • Standard
    418 pages
    English and French language
    sale 15% off
IEC
IEC 60050-447:2020(Main)
International Electrotechnical Vocabulary (IEV) - Part 447: Measuring relays and protection equipment

IEC 60050-447:2020 gives the general terminology used in measuring relays and protection equipment, as well as general terms pertaining to specific applications and associated technologies. This new edition reviews and complements the previous one. It has the status of a horizontal standard in accordance with IEC Guide 108:2006. This terminology is consistent with the terminology developed in the other specialized parts of the IEV.

  • Standard
    170 pages
    English and French language
    sale 15% off
IEC
IEC 60255-181:2019(Main)
Measuring relays and protection equipment - Part 181: Functional requirements for frequency protection

IEC 60255-181:2019 specifies the minimum requirements for functional and performance evaluation of frequency protection. This document also defines how to document and publish performance test results.
This document covers the functions based on frequency measurement or rate of change of frequency measurements. This document also covers frequency protection where additional blocking elements are used.
This document defines the influencing factors that affect the accuracy under steady state conditions and performance characteristics during dynamic conditions. The test methodologies for verifying performance characteristics and accuracy are also included in this document.

  • Standard
    188 pages
    English and French language
    sale 15% off
IEC
IEC/IEEE 60255-118-1:2018(Main)
Measuring relays and protection equipment - Part 118-1: Synchrophasor for power systems - Measurements

IEC/IEEE 60255-118-1:2018 is used for synchronized phasor measurement systems in power systems. It defines a synchronized phasor (synchrophasor), frequency, and rate of change of frequency measurements. It describes time tag and synchronization requirements for measurement of all three of these quantities. It specifies methods for evaluating these measurements and requirements for compliance with the standard under both static and dynamic conditions. It defines a phasor measurement unit (PMU), which can be a stand-alone physical unit or a functional unit within another physical unit. This document does not specify hardware, software or a method for computing phasors, frequency, or rate of change of frequency.

  • Standard
    74 pages
    English language
    sale 15% off
IEC
IEC 60255-121:2014(Main)
Measuring relays and protection equipment - Part 121: Functional requirements for distance protection

IEC 60255-121:2014 specifies minimum requirements for functional and performance evaluation of distance protection function typically used in, but not limited to, line applications for effectively earthed, three-phase power systems. This standard also defines how to document and publish performance tests. This standard covers distance protection function whose operating characteristic can be defined on an impedance plane and includes specification of the protection function, measurement characteristics, phase selection, directionality, starting and time delay characteristics. The test methodologies for verifying performance characteristics and accuracy are included in this standard. The standard defines the influencing factors that affect the accuracy under steady state conditions and performance characteristics during dynamic conditions. It also includes the instrument transformer requirements for the protection function. The general requirements for measuring relays and protection equipment are defined in IEC 60255-1.

  • Standard
    302 pages
    English and French language
    sale 15% off
IEC
IEC 60255-27:2013(Main)
Measuring relays and protection equipment - Part 27: Product safety requirements

IEC 60255-27:2013 describes the product safety requirements for measuring relays and protection equipment having a rated a.c. voltage up to 1 000 V with a rated frequency up to 65 Hz, or a rated d.c. voltage up to 1 500 V. Above these limits, IEC 60664-1 is applicable for the determination of clearance, creepage distance and withstand test voltage. This standard details essential safety requirements to minimize the risk of fire and hazards caused by electric shock or injury to the user. This new edition includes the following significant technical changes with respect to the previous edition:
- the removal of tables and diagrams which are from other standards and referring instead directly to the source standard;
- all aspects of IEC 60255-5 have been covered and this standard will be withdrawn.

  • Standard
    197 pages
    English and French language
    sale 15% off
IEC
IEC 60255-149:2013(Main)
Measuring relays and protection equipment - Part 149: Functional requirements for thermal electrical relays

IEC 60255-149:2013 specifies minimum requirements for thermal protection relays. This standard includes specification of the protection function, measurement characteristics and test methodologies. The object is to establish a common and reproducible reference for evaluating dependent time relays which protect equipment from thermal damage by measuring a.c. current flowing through the equipment. Complementary input energizing quantities such as ambient, coolant, top oil and winding temperature may be applicable for the thermal protection specification set forth in this standard. This standard covers protection relays based on a thermal model with memory function.

  • Standard
    93 pages
    English and French language
    sale 15% off
IEC
IEC 60255-26:2013(Main)
Measuring relays and protection equipment - Part 26: Electromagnetic compatibility requirements

IEC 60255-26:2013 is applicable to measuring relays and protection equipment, taking into account combinations of devices to form schemes for power system protection including the control, monitoring, communication and process interface equipment used with those systems. This standard specifies the requirements for electromagnetic compatibility for measuring relays and protection equipment. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only. This new edition includes the following significant technical changes with respect to the previous edition:
- definition of test specifications, test procedures and acceptance criteria per phenomena and port under test in one document;
- extension of radiated emission measurement for frequencies above 1 GHz;
- limitation of radiated emission measurement at 3 m distance for small equipment only;
- addition of zone A and zone B test level on surge test;
- extension of tests on the auxiliary power supply port by a.c. and d.c. voltage dips, a.c. component in d.c. (ripple) and gradual shut-down/start-up;
- harmonization of acceptance criteria for immunity tests.

  • Standard
    92 pages
    English and French language
    sale 15% off
IEC
IEC 60255-24:2013(Main)
Measuring relays and protection equipment - Part 24: Common format for transient data exchange (COMTRADE) for power systems

IEC 60255-24:2013 defines a format for files containing transient waveform and event data collected from power systems or power system models. The format is intended to provide an easily interpretable form for use in exchanging data. The standard is for files stored on currently used physical media such as portable external hard drives, USB drives, flash drives, CD, and DVD. This standard defines a common format for the data files and exchange medium needed for the interchange of various types of fault, test, and simulation data. The main changes with respect to the previous edition are as follows:
- this new edition allows single file format (with extension .CFF) in lieu of four separate files;
- the single file with .CFF extension contains four sections of information corresponding to .CFG, .INF, .HDR, and .DAT. The DAT section is either in ASCII or Binary;
- the following additional data file types are also supported: binary32 and float32.

  • Standard
    144 pages
    English and French language
    sale 15% off
IEC
IEC 60255-127:2010(Main)
Measuring relays and protection equipment - Part 127: Functional requirements for over/under voltage protection

IEC 60255-127:2010 specifies minimum requirements for over/under voltage relays. The standard includes specification of the protection function, measurement characteristics and time delay characteristics.

  • Standard
    49 pages
    English and French language
    sale 15% off