IEC PAS 61076-3-122:2015
(Main)Connectors for electronic equipment - Product requirements - Part 3-122: Detail specification for rugged 8-way, shielded, free and fixed connectors
Connectors for electronic equipment - Product requirements - Part 3-122: Detail specification for rugged 8-way, shielded, free and fixed connectors
IEC/PAS 61076-3-122:2015(E) covers 8-way unshielded free and fixed connectors, and is intended to specify the common dimensions, mechanical, electrical and environmental characteristics and tests for the family of IEC 61076-3 connectors. These connectors are intermateable and interoperable with other IEC 61076-3 series connectors. This PAS is a technical specification not fulfilling the requirements for a standard, but made available to the public. Key words: Connectors, Free and Fixed Connectors, 8-way shielded connector.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC PAS 61076-3-122 ®
Edition 1.0 2015-03
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
colour
inside
Connectors for electronic equipment – Product requirements –
Part 3-122: Detail specification for rugged 8-way, shielded, free and fixed
connectors
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing more than 30 000 terms and
Technical Specifications, Technical Reports and other definitions in English and French, with equivalent terms in 15
documents. Available for PC, Mac OS, Android Tablets and additional languages. Also known as the International
iPad. Electrotechnical Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a More than 60 000 electrotechnical terminology entries in
variety of criteria (reference number, text, technical English and French extracted from the Terms and Definitions
committee,…). It also gives information on projects, replaced clause of IEC publications issued since 2002. Some entries
and withdrawn publications. have been collected from earlier publications of IEC TC 37,
77, 86 and CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
IEC PAS 61076-3-122 ®
Edition 1.0 2015-03
PUBLICLY AVAILABLE
SPECIFICATION
PRE-STANDARD
colour
inside
Connectors for electronic equipment – Product requirements –
Part 3-122: Detail specification for rugged 8-way, shielded, free and fixed
connectors
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 31.220.10 ISBN 978-2-8322-1981-2
– 2 – IEC PAS 61076-3-122:2015 © IEC 2015
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Common features and typical connector pair . 7
4.1 View showing typical fixed and free connectors . 7
4.2 Mating information . 7
4.2.1 General . 7
4.2.2 Contacts – mating conditions . 8
4.2.3 Fixed connector TYP I . 9
4.2.4 Free connector TYP I . 12
4.2.5 Fixed connector TYP II . 14
4.2.6 Free connector TYP II . 17
5 Characteristics . 18
5.1 General . 18
5.2 Pin and pair grouping assignment . 18
5.3 Classification into climatic category . 19
5.4 Electrical characteristics . 19
5.4.1 Voltage proof . 19
5.4.2 Current-temperature derating . 19
5.4.3 Initial insulation resistance . 20
5.5 Mechanical characteristics . 20
5.5.1 Mechanical operation . 20
5.5.2 Insertion and withdrawal forces . 20
6 Tests and test schedule . 20
6.1 General . 20
6.2 Arrangement for contact resistance test . 21
6.3 Arrangement for vibration test (test phase EP5) . 22
6.4 Test procedures and measuring methods . 22
6.5 Preconditioning . 22
6.6 Test schedules . 23
6.6.1 General . 23
6.6.2 Basic (minimum) test schedule . 23
6.6.3 Full test schedule . 23
Figure 1 – View showing typical fixed and free connectors . 7
Figure 2 – Contact interface dimensions with terminated free connector . 8
Figure 3 – View of contact zone . 9
Figure 4 – Section D-D . 10
Figure 5 – Free connector Typ I . 12
Figure 6 – View of contact zone . 14
Figure 7 – Section D-D . 15
Figure 8 – Free connector . 17
Figure 9 – Fixed connector pin and pair grouping assignment (front view of connector) . 19
Figure 10 – Connector de-rating curve . 20
Figure 11 – Arrangement for contact resistance test . 21
Figure 12 – Arrangement for vibration test . 22
Table 1 – Dimensions for Figure 2 . 8
Table 2 – Dimensions for Figures 3 and 4 . 11
Table 3 – Dimensions for Figure 5 . 13
Table 4 – Dimensions for Figures 6 and 7 . 16
Table 5 – Dimensions for Figure 8 . 18
Table 6 – Climatic categories – selected values . 19
Table 7 – Test group P . 23
Table 8 – Test group AP . 24
Table 9 – Test group BP . 25
Table 10 – Test group CP . 26
Table 11 – Test group DP . 27
Table 12 – Test group EP . 28
Table 13 – Test group FP . 29
– 4 – IEC PAS 61076-3-122:2015 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
PRODUCT REQUIREMENTS –
Part 3-122: Detail specification for rugged 8-way,
shielded, free and fixed connectors
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
A PAS is a technical specification not fulfilling the requirements for a standard, but made
available to the public.
IEC PAS 61076-3-12
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.