IEC 60335-2-90:2006/AMD1:2010
(Amendment)Amendment 1 - Household and similar electrical appliances - Safety - Part 2-90: Particular requirements for commercial microwave ovens
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-90: Particular requirements for commercial microwave ovens
IEC 60335-2-90-A1:2010 Amendment 1 NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication.
Amendement 1 - Appareils électrodomestiques et analogues - Sécurité - Partie 2-90: Règles particulières pour les fours à micro-ondes à usage commercial
CEI 60335-2-90-A1:2010 Amendement 1 NOTE L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication CEI, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 12 mois et au plus tard 36 mois après la date de publication.
General Information
Relations
Standards Content (Sample)
IEC 60335-2-90 ®
Edition 3.0 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 1
AMENDEMENT 1
Household and similar electrical appliances – Safety –
Part 2-90: Particular requirements for commercial microwave ovens
Appareils électrodomestiques et analogues – Sécurité –
Partie 2-90: Règles particulières pour les fours à micro-ondes à usage
commercial
IEC 60335-2-90:2006/A1:2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 60335-2-90 ®
Edition 3.0 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 1
AMENDEMENT 1
Household and similar electrical appliances – Safety –
Part 2-90: Particular requirements for commercial microwave ovens
Appareils électrodomestiques et analogues – Sécurité –
Partie 2-90: Règles particulières pour les fours à micro-ondes à usage
commercial
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
F
CODE PRIX
ICS 97.040.20 ISBN 978-2-88912-075-8
– 2 – 60335-2-90 Amend. 1 © IEC:2010
FOREWORD
This amendment has been prepared by subcommittee 61B: Safety of microwave ovens, of IEC
technical committee 61: Safety of household and similar electrical appliances.
The text of this standard is based on the following documents:
FDIS Report on voting
61B/416/FDIS 61B/424/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 12 months or later than 36 months from the date of publication.
____________
INTRODUCTION
Replace the fifth paragraph by the following:
When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal and generic standards covering a hazard are not applicable since they have been taken into
consideration when developing the general and particular requirements for the IEC 60335 series of standards. For
example, in the case of temperature requirements for surfaces on many appliances, generic standards, such as
ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.
60335-2-90 Amend. 1 © IEC:2010 – 3 –
1 Scope
Add before Note 101:
This standard also deals with microwave ovens intended to be used on board ships, for
which Annex EE is applicable.
2 Normative references
Replace the existing text by the following:
This clause of Part 1 is applicable except as follows.
Addition:
IEC 60068-2-6, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
IEC 60068-2-27, Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock
IEC 60068-2-52, Environmental testing – Part 2-52: Tests – Test Kb: Salt mist, cyclic (sodium
chloride solution)
7 Marking and instructions
7.1 Add the following text to the addition:
If appliances have accessible metal surfaces, other than working surfaces, that have a
temperature rise exceeding 90 K during the test of Clause 11, they shall be marked with
symbol IEC 60417-5041(2002-10) or with the substance of the following:
CAUTION: Hot surface.
7.6 Add the following to the addition:
[symbol IEC 60417-5041 (2002-10)] Caution, hot surface
7.14 Add the following paragraph to the addition:
The height of the triangle used with symbol IEC 60417-5041 (2002-10) shall be at least
12 mm.
18 Endurance
Replace the existing text by the following:
This clause of Part 1 is replaced by the following.
– 4 – 60335-2-90 Amend. 1 © IEC:2010
The door system, including hinges, microwave seals and other associated parts, shall be
constructed to withstand wear that may be expected in normal use.
Compliance is checked by the following test.
The door system is subjected to 100 000 cycles of operation with the appliance supplied at
rated voltage and containing an appropriate microwave-absorbing load. It is then subjected
to 100 000 cycles of operation without microwave generation.
The door is opened and closed as in normal use. It is opened from the closed position to a
position approximately 10° before fully open. The rate of operation is 6 cycles per minute.
With the agreement of the manufacturer the rate of operation without microwave generation
can be increased to 12 cycles per minute.
After the test, the microwave leakage shall not exceed the limit specified in Clause 32 and the
door system shall still function.
NOTE 101 Controls may be rendered inoperative in order to carry out the test.
NOTE 102 Components, the deterioration of which does not impair compliance with this standard, may be
replaced in order to complete the test.
NOTE 103 Bricks or additional water of maximum 1 000 g may be added if necessary to avoid stopping of the test
due to overheating.
22 Construction
Add the following new subclause:
22.119 If electronic circuits are used to provide protection against microwave leakage they
shall be designed so that a fault condition will not affect protection against microwave
leakage.
Compliance is checked by applying the tests in Clause 19 in conjunction with the
requirements and test specifications in 22.105, 22.106, 22.107 and 22.108.
Annexes
Add the following new Annex EE:
60335-2-90 Amend. 1 © IEC:2010 – 5 –
Annex EE
(normative)
Microwave ovens intended to be used on board ships
The following modifications to this standard are applicable for microwave ovens intended to
be used on board ships.
3 Terms and definitions
3.EE.101
open deck
area which is exposed to marine environment
3.EE.102
dayroom
area which may be exposed to marine environment from time to time
6 Classification
6.2 Addition:
Appliances for open deck use shall be IPX6.
7 Marking and instructions
7.12 Addition:
The instructions for use shall also include the substance of the following.
– usage on board ships;
– installation place (open deck protective enclosure, dayrooms);
– fastening means.
22 Construction
22.EE.101 Appliances shall withstand the pulses to which they may be subjected.
Compliance is checked by carrying out the half-sine pulse tests specified in IEC 60068-2-27
under the following conditions.
The appliance is fastened in its normal position of use to a shock-testing machine by means
of straps around the enclosure.
The type of pulse is a half-sine pulse and the severity is as follows.
– application of the half-sine pulse is in all 3 axes;
– peak acceleration: 250 m/s ,
– duration of each half-sine pulse: 6 ms;
– number of half-sine pulses in each direction: 1 000 ± 10.
– 6 – 60335-2-90 Amend. 1 © IEC:2010
The appliance shall show no damage that could impair compliance with 8.1, 16.3, Clause 29
and Clause 32 and connections shall not have worked loose.
22.EE.102 Appliances shall withstand the vibrations to which they may be subjected.
Compliance is checked by carrying out the vibration tests specified in IEC 60068-2-6 under
the following conditions.
The appliance is fastened in its normal position of use upon a vibration table by means of
straps around the enclosure. The type of vibration is sinusoidal and the severity is as follows.
– direction of vibration is vertical and horizontal;
– amplitude of vibration: 0,35 mm;
– sweep frequency range: 10 Hz to 150 Hz;
– duration of the test: 30 min.
The appliance shall show no damage that could impair compliance with 8.1, 16.3, Clause 29
and Clause 32 and connections shall not have worked loose.
31 Resistance to rusting
Replacement:
This clause of part 1 is applicable except as follows.
Addition:
Compliance is checked by the salt mist test Kb of IEC 60068-2-52:
– for open deck use severity 1 is applicable;
– for dayrooms use severity 2 is applicable.
Before the test, coatings are scratched by means a hardened steel pin, the end of which has
the form of a cone with an angle of 40°. Its tip is rounded with a radius of 0,25 mm ± 0,02 mm.
The pin is loaded so that the force exerted along its axis is 10 N ±0,5 N. The scratches are
made by drawing the pin along the surface of the coating at the speed of approximately
20 mm/s. Five scratches are made at least 5 mm apart and at least 5 mm from the edges.
After the test, the appliance shall not have deteriorated to such an extent that compliance with
this standard, in particular with Clauses 8 and 27, is impaired. The coating shall not be broken
and shall not have detached from the metal surface.
___________
– 8 – 60335-2-90 Amend. 1 © CEI:2010
AVANT-PROPOS
Le présent amendement a été établi par le sous-comité 61B, Sécurité des fours à micro-
ondes, du comité d'études 61 de la CEI: Sécurité des appareils électrodomestiques et
analogues
Le texte de cet amendement est issu des documents suivants:
F
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.