iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC 61196-9-2:2022

(Main)

Coaxial communication cables - Part 9-2: Detail specification for 50-0,4 type RF flexible cables

Coaxial communication cables - Part 9-2: Detail specification for 50-0,4 type RF flexible cables

IEC 61196-9-2:2022 applies to coaxial communication cables described in IEC 61196-9. It specifies the requirements for 50-0,4 type RF flexible cables. These cables are used in routers, notebook computers, mobile phones or other electronics. The operating frequency is from 5 MHz to 6 000 MHz.

General Information

Status
Published
Publication Date
15-Mar-2022
ICS
33.120.10 - Coaxial cables. Waveguides
Technical Committee
SC 46A - Coaxial cables
Drafting Committee
WG 3 - TC 46/SC 46A/WG 3
Current Stage
PPUB - Publication issued
Start Date
11-Apr-2022
Completion Date
16-Mar-2022
Ref Project

Buy Standard

IEC 61196-9-2:2022 - Coaxial communication cables - Part 9-2: Detail specification for 50-0,4 type RF flexible cablesIEC 61196-9-2:2022 - Coaxial communication cables - Part 9-2: Detail specification for 50-0,4 type RF flexible cables
PreviousNext
Standard
IEC 61196-9-2:2022 - Coaxial communication cables - Part 9-2: Detail specification for 50-0,4 type RF flexible cables
English language
12 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC 61196-9-2
®

Edition 1.0 2022-03
INTERNATIONAL
STANDARD



Coaxial communication cables –
Part 9-2: Detail specification for 50-0,4 type RF flexible cables
IEC 61196-9-2:2022-03(en)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2022 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.


IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always
committee, …). It also gives information on projects, replaced have access to up to date content tailored to your needs.
and withdrawn publications.

Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and
and French, with equivalent terms in 19 additional languages.
once a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.

---------------------- Page: 2 ----------------------
IEC 61196-9-2

®


Edition 1.0 2022-03




INTERNATIONAL



STANDARD



















Coaxial communication cables –

Part 9-2: Detail specification for 50-0,4 type RF flexible cables


























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 33.120.10 ISBN 978-2-8322-1087-1




  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 3 ----------------------
– 2 – IEC 61196-9-2:2022 © IEC 2022
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Detail specification . 6
Annex A (normative) Cable identification and marking . 11
A.1 Cable identification . 11
A.1.1 Type name . 11
A.1.2 Variants . 11
A.2 Cable marking . 11
Annex B (normative) Maximum attenuation . 12

Table A.1 – Distinguishing number . 11
Table B.1 – Maximum attenuation .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC 61196-13:2023(Main)
Coaxial communication cables - Part 13 - Sectional specification for semi-rigid cables with silicon dioxide dielectric

IEC 61196-13:2023 specifies the materials and cable construction for semi-rigid coaxial communication cables with silicon dioxide dielectric, IEC type designation, identification, marking and labelling, standard rating and characteristics, requirements of finished cables, quality assessment, delivery and storage, etc.
This part of IEC 61196 applies to semi-rigid coaxial communication cables with silicon dioxide dielectric and tubular outer conductor. These cables are intended for use in applications requiring extreme environments as well as in nuclear power plants, oil rigs and aircraft engines.

  • Standard
    26 pages
    English language
    sale 15% off
IEC
IEC 61196-1-119:2023(Main)
Coaxial communication cables - Part 1-119: Electrical test methods - RF power for coaxial cables and cable assemblies

IEC 61196-1-119:2023 provides test methods for RF power rating and power withstanding of RF coaxial cables and cable assemblies at specified frequency, temperature and altitude.
This document is applicable to RF coaxial cables and cable assemblies.

  • Standard
    24 pages
    English language
    sale 15% off
IEC
IEC 61196-9:2023(Main)
Coaxial communication cables - Part 9: Sectional specification for flexible RF coaxial cables

IEC 61196-9:2023 specifies the materials and cable construction for RF flexible coaxial communication cables with solid or with semi-air-spaced dielectric, IEC type designation, identification, marking and labelling, standard rating and characteristics, requirements of finished cables, quality assessment, delivery and storage, etc.
This document applies to RF flexible coaxial communication cables for use in mobile communication systems, microwave test equipment and other fields. It is read in conjunction with IEC 61196-1:2005.

  • Standard
    18 pages
    English language
    sale 15% off
IEC
IEC 61196-8:2023(Main)
Coaxial communication cables - Part 8: Sectional specification for semi-flexible cables with fluoropolymer dielectric

IEC 61196-8:2023 specifies the materials and cable construction for semi-flexible coaxial communication cables with fluoropolymer dielectric, IEC type designation, identification, marking and labelling, standard rating and characteristics, requirements of finished cables, quality assessment, delivery and storage, etc.
This document applies to semi-flexible coaxial communication cables with fluoropolymer dielectric and tin soaked copper wire braid outer conductor. These cables are intended for use in mobile communication base station antenna systems, terrestrial microwave communication, radar systems and wireless equipment or other signal transmission equipment or units. It is read in conjunction with IEC 61196-1:2005.

  • Standard
    19 pages
    English language
    sale 15% off
IEC
IEC 61196-1-123:2023(Main)
Coaxial communication cables - Part 1-123: Electrical test methods - Test for attenuation constant of radiating cable

IEC 61196-1-123:2023 defines the test method to determine the attenuation constant of radiating coaxial communication cables that are intended for use in wireless communication systems such as tunnels, railways, highways, subways, elevators and other confined areas in which conventional antenna transmission is not satisfactory or even impossible.

  • Standard
    10 pages
    English language
    sale 15% off
IEC
IEC 61196-5:2022(Main)
Coaxial communication cables - Part 5: Sectional specification for CATV trunk and distribution cables

IEC 61196-5:2022, which is a sectional specification, applies to coaxial cables for analogue and digital one- and two-way signal transmission, for example for cable networks for television signals, sound signals and interactive services in accordance with IEC 60728-1, IEC 60728-1-1, IEC 60728-101, IEC 60728-10, ISO/IEC 11801-1 and ISO/IEC 11801-4. This includes also the transmission of BCT signals provided by a CATV, MATV or SMATV cable networks.
This document specifies the test procedures and requirements for trunk and distribution cables for temperatures between −40 °C and +65 °C and in the frequency range of 5 MHz to 2 000 MHz.
This fourth edition cancels and replaces the third edition published in 2018. This edition includes the following significant technical changes with respect to the previous edition:
a. complete revision; b. cable identification and marking has been added; c. Table B.1, cable types have been added.

  • Standard
    39 pages
    English language
    sale 15% off
IEC
IEC 61196-10:2022(Main)
Coaxial communication cables - Part 10: Sectional specification for semi-rigid cables with fluoropolymer dielectric

IEC 61196-10:2022 specifies the materials and cable construction for semi-rigid coaxial communication cables with fluoropolymer dielectric, IEC type designation, identification, marking and labelling, standard rating and characteristics, requirements of finished cables, quality assessment, delivery and storage, etc. This part of IEC 61196 applies to semi-rigid coaxial communication cables with fluoropolymer dielectric and tubular outer conductor. Semi-rigid coaxial communication cables with fluoropolymer dielectric are widely used in mobile communication systems, microwave test equipment, radar, aerospace and other fields.
This second edition cancels and replaces the first edition published in 2014. This edition includes the following significant technical changes with respect to the previous edition:
a. Title was changed to: Sectional specification for semi-rigid cables with fluoropolymer dielectric b. Dielectric: other fluoropolymer materials (such as FEP, PFA) were added c. Table 1 – Distinguishing number was added d. Table 2 – Rated temperature was added e. 7.4.8, Thermal cycling was deleted f. Annex A: Performance requirements of typical cables was added g. Annex B: Requirements for thermal shock was added

  • Standard
    25 pages
    English language
    sale 15% off
IEC
IEC 61196-10-1:2022(Main)
Coaxial communication cables - Part 10-1: Blank detail specification for semi-rigid cables with fluoropolymer dielectric

IEC 61196-10-1:2022 applies to coaxial communication cables described in IEC 61196-10, which specifies the requirements of semi-rigid coaxial communication cables with fluoropolymer dielectric and tubular outer conductors. Semi-rigid coaxial communication cables with fluoropolymer dielectric are widely used in mobile communication systems, microwave test equipment, radar, aerospace, electronic countermeasures and other fields.
This part of IEC 61196 is used in conjunction with IEC 61196-1 and IEC 61196-10, which determines the layout and style for detail specifications, based on the blank detail specification, that can be prepared by a national organization, a manufacturer, or a user.
This second edition cancels and replaces the first edition published in 2014. This edition includes the following significant technical changes with respect to the previous edition:
a. Title was changed to: Blank detail specification for semi-rigid cables with fluoropolymer dielectric.
b. Further changes in accordance with IEC 61196-10.

  • Standard
    11 pages
    English language
    sale 15% off
IEC
IEC 61196-1-326:2022(Main)
Coaxial communication cables - Part 1-326: Mechanical test methods - Hanger test

IEC 61196-1-326:2022 describes the test methods to evaluate the suitability of hangers to support a cable on an antenna tower, or on other constructions. This document also provides generic criteria to evaluate performance.

  • Standard
    12 pages
    English language
    sale 15% off
IEC
IEC 61196-4:2022(Main)
Coaxial communication cables - Part 4: Sectional specification for radiating cables

IEC 61196-4:2022 applies to radiating coaxial communication cables, and specifies the terms and definitions, material and construction, IEC type designation, standard rating and characteristics, identification, marking and labelling, requirements of finished cables, quality assessment, delivery and storage, etc.
This fourth edition cancels and replaces the third edition published in 2015 This edition includes the following significant technical changes with respect to the previous edition:
a. rewrote "1 Scope" to be consistent with other blank detail specifications of coaxial cables; b. updated different standards in "Clause 2 Normative references"; c. added the definitions of uniformly radiating type cable, stop frequency band and link loss; d. added different materials and constructions in 4.2 to 4.5; e. added "Clause 5 IEC type designation"; f. added a detailed rated temperature range of different materials in "6.2 Rated temperature range"; g. added detailed frequencies in "6.3 Operating frequency range"; h. added "6.4 Stop frequency band" and "6.5 Radiating characteristics"; i. added different detail requirements or typical values in 8.2.4, 8.2.7, 8.2.8, 8.4.3 to 8.4.8; j. deleted "7.4.4 Ovality of outer conductor"; k. added "8.2.11 Link loss", "8.4.9 Adhesion of dielectric", "8.4.10 Shrinkage for insulations", "8.4.11 Maximum pulling force of cable";
i. used IEC 61196-1-123 and IEC 61196-1-124 in the electrical requirements to replace Annex A and Annex B respectively and deleted Annex A and Annex B; m. added "Figure A.1 Example of testing coupling loss around circumferential orientation of radiating cable (Y-Z)" in Annex A.

  • Standard
    83 pages
    English language
    sale 15% off