IEC 61196-11:2016

Coaxial communication cables - Part 11: Sectional specification for semi-rigid cables with polyethylene (PE) dielectric

IEC 61196-11:2016 applies to semi-rigid coaxial communication cables with polyethylene (PE) dielectric and tubular outer conductor. These cables are intended for use in microwave and wireless equipments or other signal transmission equipments or units at frequencies above 500 MHz.
This publication is to be read in conjunction with IEC 61196-1:2005.

General Information

• Status: Published
• Publication Date: 04-Jan-2016
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 33.120.10 - Coaxial cables. Waveguides
• Technical Committee: SC 46A - Coaxial cables
• Drafting Committee: WG 3 - TC 46/SC 46A/WG 3
• Current Stage: DELPUB - Deleted Publication
• Start Date: 03-Feb-2021
• Completion Date: 16-Mar-2022

Relations

• Revised: IEC 61196-11:2022 - Coaxial communication cables - Part 11: Sectional specification for semi-rigid cables with polyethylene (PE) dielectric
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 61196-11 ®
Edition 1.0 2016-01
INTERNATIONAL
STANDARD
Coaxial communication cables –
Part 11: Sectional specification for semi-rigid cables with polyethylene (PE)
dielectric
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]
CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 15 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: [e-mail].
IEC61196-11 ®
Edition 1.0 2016-01
INTERNATIONAL
STANDARD
Coaxial communication cables –

Part 11: Sectional specification for semi-rigid cables with polyethylene (PE)

dielectric
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.120.10 ISBN 978-2-8322-3091-6

– 2 – IEC 61196-11:2016 © IEC 2016
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Materials and cable construction . 7
4.1 Cable construction . 7
4.2 Inner conductor . 7
4.2.1 Conductor material . 7
4.2.2 Conductor construction . 7
4.3 Dielectric . 8
4.4 Outer conductor . 8
4.5 Sheath . 8
5 Standard rating and characteristics . 9
5.1 Nominal characteristic wave impedance . 9
5.2 Rated temperature range . 9
5.3 Operating frequency . 9
5.4 Average and peak power . 9
6 Identification, marking and labelling . 9
6.1 Cable identification . 9
6.2 Cable marking . 9
6.3 Labelling . 9
7 Requirements of finished cables . 9
7.1 General . 9
7.2 Electrical requirements . 10
7.3 Environmental requirements . 11
7.4 Mechanical requirements . 12
7.5 Fire performance requirements . 13
8 Quality assessment . 13
9 Delivery and storage . 13

Table 1 – Rated temperature . 9
Table 2 – Electrical requirements . 10
Table 3 – Environmental requirements . 11
Table 4 – Mechanical requirements. 12
Table 5 – Fire performance requirements . 13

INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COAXIAL COMMUNICATION CABLES –

Part 11: Sectional specification for semi-rigid cables
with polyethylene (PE) dielectric

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61196-11 has been prepared by subcommittee 46A: Coaxial
cables, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and
microwave passive components and accessories.
The text of this standard is based on the following documents:
FDIS Report on voting
46A/1280/FDIS 46A/1291/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

– 4 – IEC 61196-11:2016 © IEC 2016
It is to be read in conjunction with IEC 61196-1:2005, on which it is based.
A list of all parts in the IEC 61196 series, under the general title: Coaxial communication
cables, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

COAXIAL COMMUNICATION CABLES –

Part 11: Sectional specification for semi-rigid cables
with polyethylene (PE) dielectric

1 Scope
This part of IEC 61196 applies to semi-rigid coaxial communication cables with polyethylene
(PE) dielectric and tubular outer conductor. These cables are intended for use in microwave
and wireless equipments or other signal transmission equipments or units at frequencies
above 500 MHz.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60068-1:2013, Environmental testing – Part 1: General and guidance
IEC 60096-0-1:2012, Radio frequency cables – Part 1- 0: Guide to the design of detail
specifications – Section 1 – Coaxial cables
IEC 60096-0-1:2012/ AMD1:___
IEC 60332-1-2, Tests on electric and optical fibre cables under fire conditions – Part 1-2: Test
for vertical flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-
mixed flame
IEC 60811-406:2012, Electric and optical fibre cables – Test methods for non-metallic
materials – Part 406: Miscellaneous tests – Resistance to stress cracking of polyethylene and
polypropylene compounds
IEC 60754-1, Test on gases evolved during combustion of materials from cables – Part 1:
Determination of the halogen acid gas content
IEC 61034-2, Measurement of smoke density of cables burning under defined conditions –
Part 2: Test procedure and requirements
IEC 61169-4, Radio-frequency connectors – Part 4: RF coaxial connectors with inner
diameter of outer conductor 16 mm (0,63 in) with screw lock – Characteristic impedance 50 Ω
(type 7-16)
IEC 61196-1 (all parts), Coaxial communication cables
IEC 61196-1:2005, Coaxial communication cables – Part 1: Generic specification – General,
definitions and requirements
___________
To be published.
– 6 –
...