IEC 60384-20-1:2008

Fixed capacitors for use in electronic equipment - Part 20-1: Blank detail specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors - Assessment level EZ

IEC 60384-20-1:2008 is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described.

Condensateurs fixes utilisés dans les équipements électroniques - Partie 20-1: Spécification particulière cadre - Condensateurs fixes pour montage en surface pour courant continu à diélectrique en film de sulfure de polyphénylène métallisé - Niveau d'assurance EZ

La CEI 60384-20-1:2008 est un document annexe à la spécification intermédiaire qui contient des exigences pour le modèle, la disposition et le contenu minimal des spécifications particulières. Les spécifications particulières qui ne satisfont pas aux exigences peuvent ne pas être considérées comme conformes aux spécifications de la CEI et ne doivent pas être décrites comme telles.

General Information

• Status: Withdrawn
• Publication Date: 21-Jan-2008
• Withdrawal Date: 06-Jul-2023
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 31.060.10 - Fixed capacitors
• Technical Committee: TC 40 - Capacitors and resistors for electronic equipment
• Current Stage: WPUB - Publication withdrawn
• Start Date: 07-Jul-2023
• Completion Date: 07-Jul-2023

Relations

• Corrected By: IEC 60384-20-1:2008/COR1:2008 - Corrigendum 1 - Fixed capacitors for use in electronic equipment - Part 20-1: Blank detail specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors - Assessment level EZ
• Effective Date: 05-Sep-2023
• Revises: IEC 60384-20-1:1996 - Fixed capacitors for use in electronic equipment - Part 20: Blank detail specification: Fixed metallized polyphenylene sulfide film dielectric chip d.c. capacitors. Assessment level EZ
• Effective Date: 05-Sep-2023

Standards Content (Sample)

IEC 60384-20-1
Edition 2.0 2008-01
INTERNATIONAL
STANDARD
QC 302001
Fixed capacitors for use in electronic equipment –
Part 20-1: Blank detail specification – Fixed metallized polyphenylene sulfide
film dielectric surface mount d.c. capacitors – Assessment level EZ

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,

please contact the address below or your local IEC member National Committee for further information.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: [e-mail]
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: [e-mail]
Tel.: [phone]
Fax: [phone]
IEC 60384-20-1
Edition 2.0 2008-01
INTERNATIONAL
STANDARD
QC 302001
Fixed capacitors for use in electronic equipment –
Part 20-1: Blank detail specification – Fixed metallized polyphenylene sulfide
film dielectric surface mount d.c. capacitors – Assessment level EZ

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
M
ICS 31.060.10 ISBN 2-8318-9548-0

– 2 – 60384-20-1 © IEC:2008(E)

INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 20-1: Blank detail specification –

Fixed metallized polyphenylene sulfide film

dielectric surface mount d.c. capacitors –

Assessment level EZ
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-20-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This second edition cancels and replaces the first edition published in 1996 and constitutes a
minor revision related to tables and references.
The text of this standard is based on the following documents:
FDIS Report on voting
40/1872/FDIS 40/1889/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

60384-20-1 © IEC:2008(E) – 3 –

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

The list of all parts of the IEC 60384 series, under the (new) general title Fixed capacitors for

use in electronic equipment, can be found on the IEC website.

The QC number that appears on the front cover of this publication is the specification number

in the IECQ Quality Assessment System for Electronic Components.

The committee has decided that the contents of this publication will remain unchanged until

the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in

the data related to the specific publication. At this date, the publication will be

• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
The contents of the corrigendum of February 2008 have been included in this copy.

– 4 – 60384-20-1 © IEC:2008(E)

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 20-1: Blank detail specification –

Fixed metallized polyphenylene sulfide film

dielectric surface mount d.c. capacitors –

Assessment level EZ
Blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style and layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in
accordance with IEC specifications nor shall they so be described.
In the preparation of detail specifications, the content of 1.4 of the sectional specification shall
be taken into account.
The numbers between brackets on the first page correspond to the following information
which shall be inserted in the position indicated.
Identification of the detail specification
[1] The "International Electrotechnical Commission" or the National Standards Organization
under whose authority the detail specification is drafted.
[2] The IEC or National Standards number of the detail specification, date of issue and any
further information required by the national system.
[3] The number and issue number of the IEC or national generic specification.
[4] The IEC number of the blank detail specification.
Identification of the capacitor
[5] A short description of the type of capacitor.
[6] Information on typical construction (when applicable).
When the capacitor is not designed for use in printed-board applications, this shall be
clearly stated in the detail specification in this position.
[7] Outline drawing with main dimensions which are of importance for interchangeability

and/or reference to the national or international documents for outlines. Alternatively,
this drawing may be given in an annex to the detail specification.
[8] Application or group of applications covered and/or assessment level.
NOTE The assessment level(s) to be used in a detail specification are selected from 3.5.4 of the sectional
specification. This implies that one blank detail specification may be used in combination with several assessment
levels, provided the grouping of the tests does not change.
[9] Reference data on the most important properties, to allow comparison between the
various capacitor types.
60384-20-1 © IEC:2008(E) – 5 –

IEC 60384-20-1XX
[2]
[1] QC 302001XXXXXX
ELECTRONIC COMPONENTS OF ASSESSED IEC 60384-20-1  [4]

QUALITY IN ACCORDANCE WITH: QC 302001

FIXED METALLIZED  [5]
[3]
POLYETHYLENE SULFIDE
FILM DIELECTRIC SURFACE MOUNT D.C.
Outline drawing: (see Table 1) CAPACITORS
[.angle projection]
[6]
[7]
Assessment level(s): EZ  [8]
[Other shapes are permitted within the dimensions given.]

Information on the availability of components qualified to this
detail specification is given in the Register of Approvals

(9)
1 General data
1.1 Recommended method(s) of mounting (to be inserted)
See 1.4.2 of IEC 60384-20.
1.2 Dimensions
Table 1 – Dimensions
Dimensions
Case size
mm
reference
L W H L L L .
1 1 1 2 3 4
When there is no case size reference, Table 1 may be omitted and the dimensions shall be
given in Table 2, which then becomes Table 1.
The dimensions shall be given as maximum dimensions or as nominal dimensions with a
tolerance.
– 6 – 60384-20-1 © IEC:2008(E)

1.3 Ratings and characteristics

Capacitance range (see Table 2)

Tolerance on rated capacitance

Rated voltage (see Table 2)
Category voltage (if applicable) (see Table 2)

Climatic category
Rated temperature
Maximum a.c. voltage (if applicable)

Maximum pulse load (if applicable)
Tangent of loss angle
Insulation resistance
Table 2 – Values of capacitance and of voltage related to case sizes
Rated voltage
a
Category voltage
Case size Case size Case size Case size
Rated capacitance
(in nF and/or μF)
a
If different from the rated voltage.

1.4 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60384-1, Fixed capacitors for use in electronic equipment – Part 1: Generic specification
IEC 60384-20, Fixed capacitors for use in electronic equipment – Part 20: Sectional
specification – Fixed metallized polyphenylene sulfide film dielectric surface mount d.c.
capacitors
1.5 Marking
The marking of the capacitor and the package shall be in accordance with the requirements of

1.6 of IEC 60384-20.
The details of the marking of the component and package shall be given in full in the detail
specification.
1.6 Ordering information
Orders for capacitors covered by this specification shall contain, in clear or in coded form, the
following minimum information:
a) rated capacitance;
b) tolerance on rated capacitance;
c) rated d.c. voltage;
d) number and issue reference of the detail specification and style reference;
e) packaging instructions.
60384-20-1 © IEC:2008(E) – 7 –

1.7 Certified records of released lots

Required/not required.
1.8 Additional information (not for inspection purposes)

1.9 Additional or increased severities or requirements to those specified in the
generic and/or sectional specification

NOTE Additions or increased requirements should be specified only when essential.

Table 3 – Other characteristics

This table is to be used for defining characteristics which are additional to,
or more severe than, those given in the sectional specification.

2 Inspection requirements
2.1 Procedures
2.1.1 For qualification approval, the procedures shall be in accordance with 3.4 of the
sectional specification IEC 60384-20.
2.1.2 For quality conformance inspection, the test schedule (Table 4) includes sampling,
periodicity, severities and requirements. The formation of inspection lots is covered by 3.5.1
of IEC 60384-20.
– 8 – 60384-20-1 © IEC:2008(E)

Table 4 – Test schedule for quality conformance inspection

D IL n c
Subclause number or a Performance
Conditions of test
a c a
c
and test ND requirements
Group A inspection
(lot-by-lot)
d
Sub-group A0
ND 100 %
4.3.2 Capacitance   Within specified tolerance
...

IEC 60384-20-1 ®
Edition 2.0 2008-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fixed capacitors for use in electronic equipment –
Part 20-1: Blank detail specification – Fixed metallized polyphenylene sulfide film
dielectric surface mount d.c. capacitors – Assessment level EZ

Condensateurs fixes utilisés dans les équipements électroniques –
Partie 20-1: Spécification particulière cadre – Condensateurs fixes pour montage
en surface pour courant continu à diélectrique en film de sulfure de
polyphénylène métallisé – Niveau d’assurance EZ

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office Tel.: [phone]
3, rue de Varembé Fax: [phone]
CH-1211 Geneva 20 [e-mail]
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.

IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: [e-mail].

A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.

Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.
Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: [e-mail].
IEC 60384-20-1 ®
Edition 2.0 2008-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fixed capacitors for use in electronic equipment –

Part 20-1: Blank detail specification – Fixed metallized polyphenylene sulfide film

dielectric surface mount d.c. capacitors – Assessment level EZ

Condensateurs fixes utilisés dans les équipements électroniques –

Partie 20-1: Spécification particulière cadre – Condensateurs fixes pour montage

en surface pour courant continu à diélectrique en film de sulfure de

polyphénylène métallisé – Niveau d’assurance EZ

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX M
ICS 31.060.10 ISBN 978-2-83220-701-7

– 2 – 60384-20-1  IEC:2008
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 20-1: Blank detail specification –
Fixed metallized polyphenylene sulfide film
dielectric surface mount d.c. capacitors –
Assessment level EZ
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-20-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This second edition cancels and replaces the first edition published in 1996 and constitutes a
minor revision related to tables and references.
This bilingual version (2013-05) corresponds to the monolingual English version, published in
2008-01.
60384-20-1  IEC:2008 – 3 –
The text of this standard is based on the following documents:
FDIS Report on voting
40/1872/FDIS 40/1889/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
The French version of this standard has not been voted upon.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The list of all parts of the IEC 60384 series, under the (new) general title Fixed capacitors for
use in electronic equipment, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
The contents of the corrigendum of February 2008 have been included in this copy.

– 4 – 60384-20-1  IEC:2008
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 20-1: Blank detail specification –
Fixed metallized polyphenylene sulfide film
dielectric surface mount d.c. capacitors –
Assessment level EZ
Blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style and layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in
accordance with IEC specifications nor shall they so be described.
In the preparation of detail specifications, the content of 1.4 of the sectional specification shall
be taken into account.
The numbers between brackets on the first page correspond to the following information
which shall be inserted in the position indicated.
Identification of the detail specification
[1] The "International Electrotechnical Commission" or the National Standards Organization
under whose authority the detail specification is drafted.
[2] The IEC or National Standards number of the detail specification, date of issue and any
further information required by the national system.
[3] The number and issue number of the IEC or national generic specification.
[4] The IEC number of the blank detail specification.
Identification of the capacitor
[5] A short description of the type of capacitor.
[6] Information on typical construction (when applicable).
When the capacitor is not designed for use in printed-board applications, this shall be
clearly stated in the detail specification in this position.
[7] Outline drawing with main dimensions which are of importance for interchangeability
and/or reference to the national or international documents for outlines. Alternatively,
this drawing may be given in an annex to the detail specification.
[8] Application or group of applications covered and/or assessment level.
NOTE The assessment level(s) to be used in a detail specification are selected from 3.5.4 of the sectional
specification. This implies that one blank detail specification may be used in combination with several assessment
levels, provided the grouping of the tests does not change.
[9] Reference data on the most important properties, to allow comparison between the
various capacitor types.
60384-20-1  IEC:2008 – 5 –
IEC 60384-20-1XX
[2]
[1] QC 302001XXXXXX
ELECTRONIC COMPONENTS OF ASSESSED IEC 60384-20-1  [4]
QUALITY IN ACCORDANCE WITH: QC 302001

FIXED METALLIZED  [5]
[3] POLYETHYLENE SULFIDE
FILM DIELECTRIC SURFACE MOUNT D.C.
Outline drawing: (see Table 1) CAPACITORS
[.angle projection]
[6]
[7]
Assessment level(s): EZ  [8]
[Other shapes are permitted within the dimensions given.]

Information on the availability of components qualified to this
detail specification is given in the Register of Approvals

(9)
1 General data
1.1 Recommended method(s) of mounting (to be inserted)
See 1.4.2 of IEC 60384-20.
1.2 Dimensions
Table 1 – Dimensions
Dimensions
Case size
mm
reference
L W H L L L .
1 1 1 2 3 4
When there is no case size reference, Table 1 may be omitted and the dimensions shall be
given in Table 2, which then becomes Table 1.
The dimensions shall be given as maximum dimensions or as nominal dimensions with a
tolerance.
– 6 – 60384-20-1  IEC:2008
1.3 Ratings and characteristics
Capacitance range (see Table 2)
Tolerance on rated capacitance
Rated voltage (see Table 2)
Category voltage (if applicable) (see Table 2)
Climatic category
Rated temperature
Maximum a.c. voltage (
...