ISO 11660-4:2012

Cranes — Access, guards and restraints — Part 4: Jib cranes

ISO 11660-4:2012 establishes the particular requirements relating to access, guards and restraints for jib cranes as defined in ISO 4306-1.

Appareils de levage à charge suspendue — Moyens d'accès, dispositifs de protection et de retenue — Partie 4: Grues à flèche

General Information

• Status: Published
• Publication Date: 05-Feb-2012
• ICS: 53.020.20 - Cranes
• Technical Committee: ISO/TC 96/SC 8 - Jib cranes
• Drafting Committee: ISO/TC 96/SC 8 - Jib cranes
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 22-Sep-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11660-4
First edition
2012-02-01
Cranes — Access, guards and restraints —
Part 4:
Jib cranes
Appareils de levage à charge suspendue — Moyens d’accès, dispositifs
de protection et de retenue —
Partie 4: Grues à flèche
Reference number
ISO 11660-4:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 11660-4:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11660-4:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11660-4 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 8, Jib cranes.
ISO 11660 consists of the following parts, under the general title Cranes — Access, guards and restraints:
— Part 1: General
— Part 2: Mobile cranes
— Part 3: Tower cranes
— Part 4: Jib cranes
— Part 5: Bridge and gantry cranes
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 11660-4:2012(E)
Cranes — Access, guards and restraints —
Part 4:
Jib cranes
1 Scope
This part of ISO 11660 establishes the particular requirements relating to access, guards and restraints for jib
cranes as defined in ISO 4306-1.
ISO 11660-1 establishes the general requirements for access to control stations and other areas of cranes as
defined in ISO 4306-1, during normal operations, maintenance, inspection, erection and dismantling. It also
deals with guards and restraints in general, concerning the protection of persons on or near the crane with
regard to moving parts, falling objects or live parts.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 11660-1:2008, Cranes — Access, guards and restraints — Part 1: General
ISO 13852, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 11660-1 apply.
4 Access
4.1 General
All control stations and other parts of the crane during normal operations, inspection, maintenance, erection or
dismantling operations, as necessary, shall be accessible by means of walkways, stairs, ladders, landings or
by mobile, ground-mounted access facilities.
4.2 Requirements
4.2.1 General design requirements for access
4.2.1.1 Compliance with ISO 11660-1
The design requirements for access shall comply with the clauses/subclauses of ISO 11660-1:2008 specified in
Table 1 below, completed by the corresponding subclauses of this part of ISO 11660 specified in the same table.
© ISO 2012 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 11660-4:2012(E)
Table 1 — Design requirements for access
Applicable clause/subclause Applicable subclause
Hazard/access means
of ISO 116
...