ISO 19356:2016

Ships and marine technology — Marine cranes — Test specifications and procedures

ISO 19356:2016 describes the required tests and the testing procedures for marine cranes of metal construction. ISO 19356:2016 is applicable to the following types of marine cranes: - deck cranes mounted on ships for handling cargo or containers in harbour or sheltered water conditions; - floating cranes or grab cranes mounted on barges or pontoons for operating in harbour conditions; - engine room cranes, provision cranes, etc. mounted on ships (including floating docks) for handling equipment and stores in harbour conditions. NOTE Marine cranes in other types can refer to this document. ISO 19356:2016 does not apply to the following: - minimum ambient operating temperatures below −20 °C; - maximum ambient operating temperatures above +45 °C; - loads from accidents or collisions; - lifting operations below sea level; - transport, assembly, dismantling and decommissioning of cranes; - lifting accessories, i.e. any item between the crane and the load; - lifting operations involving more than one crane; - hand-powered cranes; - emergency rescue operations; - shore-side cargo handling cranes; - portable cranes on board; - lifting appliances for lifeboats, liferafts accommodation ladders, and pilot ladders; - launching appliances for survival craft and rescue boats; - gangways, accommodation and pilot ladders and their handling appliances. Cranes defined in this document are intended to comply with the requirements of class societies and flag states. It is also intended that reference be made to ILO and particularly the convention No. 152. Applicable regulations are those issued by the responsible classification societies and it is intended that national authorities be complied with.

Navires et technologie maritime — Grues maritimes — Spécifications et procédures de test

General Information

• Status: Published
• Publication Date: 20-Sep-2016
• ICS: 47.020.40 - Lifting and cargo handling equipment
• Technical Committee: ISO/TC 8/SC 4 - Outfitting and deck machinery
• Drafting Committee: ISO/TC 8/SC 4 - Outfitting and deck machinery
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 09-Aug-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 19356
First edition
2016-09-15
Ships and marine technology —
Marine cranes — Test specifications
and procedures
Navires et technologie maritime — Grues maritimes — Spécifications
et procédures de test
Reference number
ISO 19356:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 19356:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 19356:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Test specification and procedure requirements . 2
4.1 General requirements . 2
4.2 Functional test . 2
4.2.1 General. 2
4.2.2 Check items before functional test . 3
4.2.3 Functional test items . 3
4.2.4 Check items after functional test . 3
4.3 Bench test . 3
4.3.1 General. 3
4.3.2 Pre-test check . 3
4.3.3 Bench test items . 4
4.4 Inclination test . 5
4.5 Other tests . 5
Bibliography . 6
© ISO 2016 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 19356:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee
SC 4, Outfitting and deck machinery.
iv © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 19356:2016(E)
Ships and marine technology — Marine cranes — Test
specifications and procedures
1 Scope
This document describes the required tests and the testing procedures for marine cranes of metal
construction.
This document is applicable to the following types of marine cranes:
— deck cranes mounted on ships for handling cargo or containers in harbour or sheltered water
conditions;
— floating cranes or grab cranes mounted on barges or pontoons for operating in harbour conditions;
— engine room cranes, provision cranes, etc. mounted on ships (including floating docks) for handling
equipment and stores in harbour conditions.
NOTE Marine cranes in other types can refer to this document.
This document does not apply to the following:
— minimum ambient operating temperatures below −20 °C;
— maximum ambient operating temperatures above +45 °C;
— loads from accidents or collisions;
— lifting operations below sea level;
— transport, assembly, dismantling and decommissioning of cranes;
— lifting accessories, i.e. any item between the crane and the load;
— lifting operations involving more than one crane;
— hand-powered cranes;
— emergency rescue operations;
— shore-side cargo handling cranes;
— portable cranes on board;
— lifting appliances for lifeboats, liferafts accommodation ladders, and pilot ladders;
— launching appliances for survival craft and rescue boats;
— gangways, accommodation and pilot ladders and their handling appliances.
Cranes defined in this document are intended to comply with the requirements of class societies and
flag states. It is also intended that reference be made to ILO and particularly the convention No. 152.
Ap
...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 19356
ISO/TC 8/SC 4 Secretariat: SAC
Voting begins on: Voting terminates on:
2015-06-30 2015-09-30
Ships and Marine Technology — Marine cranes — Test
specification and procedures
Navires et technologie maritime — Grues maritimes — Spécification de test et procédures
ICS: 47.020.40
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19356:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015

---------------------- Page: 1 ----------------------
ISO/DIS 19356:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 19356:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test specification and procedure requirements . 2
4.1 General requirements . 2
4.2 Functional test . 2
4.3 Bench test . 3
4.4 Inclination test . 4
4.5 Other tests . 4
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 19356:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee
SC 4, Outfitting and Deck Machinery.
iv © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 19356:2015(E)
Ships and Marine Technology — Marine cranes — Test
specification and procedures
1 Scope
This International Standard specifies the requirements for the test specification and procedures of
marine cranes.
1.1 Marine cranes applicable to this International Standard include the following types of cranes:
Deck cranes mounted on ships for handling cargo or containers in harbour conditions;
Floating cranes or grab cranes mounted on barges or pontoons for operating in harbour conditions;
Engine room cranes and provision cranes etc. mounted on ships (including floating docks) for handling
equipment and stores in harbour conditions.
1.2 This International Standard does not apply to:
Transport, assembly, dismantling and decommissioning of cranes,
Lifting accessories, i.e. any item between the crane and the load,
Lifting operations involving more than one crane,
Hand powered cranes,
Emergency rescue operations (except training),
Shore-side cargo handling cranes,
Portable cranes on board,
Lifting appliances for lifeboats, liferafts accommodation ladders and pilot ladders.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edit
...