ISO 10333-1:2000/Amd 1:2002

Personal fall-arrest systems — Part 1: Full-body harnesses — Amendment 1

Systèmes individuels d'arrêt de chute — Partie 1: Harnais complet — Amendement 1

General Information

• Status: Published
• Publication Date: 13-Mar-2002
• ICS: 13.340.60 - Protection against falling and slipping
• Technical Committee: ISO/TC 94/SC 4 - Personal equipment for protection against falls
• Drafting Committee: ISO/TC 94/SC 4 - Personal equipment for protection against falls
• Current Stage: 6060 - International Standard published
• Completion Date: 14-Mar-2002

Relations

• Child: ISO 10333-1:2000 - Personal fall-arrest systems — Part 1: Full-body harnesses
• Effective Date: 15-Apr-2008
• Amends: ISO 10333-1:2000 - Personal fall-arrest systems — Part 1: Full-body harnesses
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10333-1
First edition
2000-07-01
AMENDMENT 1
2002-03-15

Personal fall-arrest systems —
Part 1:
Full-body harnesses
AMENDMENT 1
Systèmes individuels d'arrêt de chute —
Partie 1: Harnais complet
AMENDEMENT 1




Reference number
ISO 10333-1:2000/Amd.1:2002(E)
©
ISO 2002

---------------------- Page: 1 ----------------------
ISO 10333-1:2000/Amd.1:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland

ii © ISO 2002 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10333-1:2000/Amd.1:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this Amendment may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to International Standard ISO 10
...