ISO 9477:2015

High strength cast steels for general engineering and structural purposes

ISO 9477:2015 specifies requirements for four grades of heat treated cast carbon and alloy steels for general engineering and structural purposes. In cases where castings are produced by welding component parts together, this International Standard does not cover the welding process or the properties of the weldment. The four steel grades are intended for service at ambient temperature. However, properties at other temperatures can be agreed on through the use of supplementary requirements in ISO 4990.

Aciers moulés à haute résistance pour construction mécanique et construction métallique d'usage général

General Information

• Status: Withdrawn
• Publication Date: 07-Sep-2015
• ICS: 77.140.80 - Iron and steel castings
• Technical Committee: ISO/TC 17/SC 11 - Steel castings
• Drafting Committee: ISO/TC 17/SC 11 - Steel castings
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 09-Nov-2023

Relations

• Revised: ISO 9477:2023 - High-strength cast steels for general engineering and structural purposes
• Effective Date: 06-Jun-2022
• Revises: ISO 9477:1992 - High strength cast steels for general engineering and structural purposes
• Effective Date: 12-Feb-2011

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 9477
Second edition
2015-09-15
High strength cast steels for general
engineering and structural purposes
Aciers moulés à haute résistance pour construction mécanique et
construction métallique d’usage général
Reference number
ISO 9477:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 9477:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 9477:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 General conditions for delivery . 1
4 Heat treatment . 1
5 Chemical requirements . 1
6 Mechanical properties . 1
7 Supplementary requirements . 2
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 9477:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 17, Steel, Subcommittee SC 11, Steel castings.
This second edition cancels and replaces the first edition (ISO 9477:1992), which has been technically
revised with the following changes:
—
...