ISO 10762:1997
(Main)Hydraulic fluid power — Cylinder mounting dimensions — 10 MPa (100 bar) series
Hydraulic fluid power — Cylinder mounting dimensions — 10 MPa (100 bar) series
Transmissions hydrauliques — Dimensions d'interchangeabilité des vérins — Série 10 MPa (100 bar)
Fluidna tehnika - Hidravlika - Vgradne mere valjev - Vrsta 10 MPa (100 barov)
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 10762
First edition
1997-12-01
Hydraulic fluid power — Cylinder mounting
dimensions — 10 MPa (100 bar) series
Transmissions hydrauliques — Dimensions d'interchangeabilité des
vérins — Série 10 MPa (100 bar)
A
Reference number
ISO 10762:1997(E)
---------------------- Page: 1 ----------------------
ISO 10762:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 10762 was prepared by Technical Committee
ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders.
Annex A of this International Standard is for information only.
© ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
---------------------- Page: 2 ----------------------
©
ISO ISO 10762:1997(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled
through a liquid under pressure within an enclosed circuit.
One component of such systems is the fluid power cylinder. This is a
device which converts power into linear mechanical force and motion. It
consists of a movable element, i.e. a piston and piston rod, operating
within a cylindrical bore.
iii
---------------------- Page: 3 ----------------------
©
INTERNATIONAL STANDARD ISO ISO 10762:1997(E)
Hydraulic fluid power — Cylinder mounting dimensions —
10 MPa (100 bar) series
1 Scope
1)
This International Standard establishes mounting dimensions for cylinders for use at 10 MPa [100 bar ], as required
for interchangeability of these cylinders.
NOTE — This International Standard allows manufacturers of hydraulic equipment flexibility in the design of 10 MPa (100 bar)
cylinders and does not restrict technical development; however, it does provide basic guidelines.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 273:1979, Fasteners — Clearance holes for bolts and screws.
ISO 286-2:1988, ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for
holes and shafts.
2)
ISO 1179-1:— , Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with
elastomeric or metal-to-metal sealing — Part 1: Threaded ports.
ISO 3320:1987, Fluid power systems and components — Cylinder bores and piston rod diameters — Metric series.
ISO 4395:1978, Fluid power systems and components — Cylinders — Piston rod thread dimensions and types.
ISO 5598:1985, Fluid power systems and components — Vocabulary.
ISO 6149-1:1993, Connections for fluid power and general use — Ports and stud ends with ISO 261 threads and
O-ring sealing — Part 1: Ports with O-ring seal in truncated housing.
ISO 8133:1991, Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar) compact series — Accessory
mounting dimensions.
5 2
1) 1 bar = 0,1 MPa = 10 Pa; 1 MPa = 1 N/mm
2) To be published. (Revision, in part, of ISO 1179:1981)
1
---------------------- Page: 4 ----------------------
©
ISO
ISO 10762:1997(E)
3 Definitions
For the purposes of this International Standard, the definitions given in ISO 5598 and the following definitions
apply.
3.1 cylinder: Device which converts fluid power into linear mechanical force and motion.
3.2 cylinder bore: Internal diameter of the cylinder body.
3.3 piston rod: Element which transmits mechanical force and motion from the piston.
3.4 mounting: Device by which a cylinder is fastened to its mating element.
4 Dimensions
Mounting dimensions for cylinders manufactured in accordance with this International Standard shall be as given in
figures 1 to 13 and tables 1 to 13. Most tolerances are in accordance with ISO 286-2.
5 Bore sizes
The following bore sizes in accordance with ISO 3320, in millimetres, are included in this series:
40 — 50 — 63 — 80 — 100 — 125 — 160 — 200
6 Mounting types
This International Standard includes the following mounting types which conform to ISO 6099:
ME5 — Rectangular flange, integral with head (see figure 3 and table 3)
ME6 — Cap, rectangular flange (see figure 4 and table 4)
MP1 — Cap, fixed clevis (see figure 5 and table 5)
MP3 — Cap, fixed eye (see figure 6 and table 6)
MP5 — Cap, fixed eye with spherical plain bearing (see figure 7 and table 7)
MS2 — Side lugs (see figure 8 and table 8)
MT1 — Head, integral trunnion (male) (see figure 9 and table 9)
MT4 — Intermediate, fixed or movable trunnion (male) (see figure 10 and table 10)
MX1 — Both ends, studs or tie rods extended (see figure 11 and table 11)
MX2 — Cap, studs or tie rods extended (see figure 12 and table 12)
MX3 — Head, studs or tie rods extended (see figure 13 and table 13)
7 Piston rod characteristics
7.1 This International Standard covers piston rods which have a shouldered male thread end (see figure 1 and
table 1 for basic dimensions).
7.2 For internally threaded rod ends, see ISO 4395.
2
---------------------- Page: 5 ----------------------
©
ISO
ISO 10762:1997(E)
7.3 If other piston rod diameters or other piston rod threads are required, those specified in ISO 3320 and
ISO 4395 shall be used.
8 Identification statement (Reference to this International Standard)
Use the following statement in test reports, catalogues and sales literature when electing to comply with this
International Standard:
“Interchangeable mounting dimensions for 10 MPa (100 bar) cylinders are selected in accordance with
ISO 10762:1997, Hydraulic fluid power — Cylinder mounting dimensions — 10 MPa (100 bar) series.”
Figure 1 — Basic dimensions
Table 1 — Basic dimensions
Dimensions in millimetres
1) 2)
MM KK A E H
Bore
max. max. max.
18 or 28 M14 · 1,5 18
40 52 5
28 M20 · 1,5 28
22 or 36 M16 · 1,5 22
50 65 5
36 M27 · 2 36
28 or 45 M20 · 1,5 28
63 77 3
45 M33 · 2 45
36 or 56 M27 · 2 36
80 96 4
56 M42 · 2 56
45 or 70 M33 · 2 45
100 115 5
70 M48 · 2 63
56 or 90 M42 · 2 56
125 140 —
90 M64 · 3 85
70 or 110 M48 · 2 63
160 18
...
SLOVENSKI STANDARD
SIST ISO 10762:1998
01-december-1998
Fluidna tehnika - Hidravlika - Vgradne mere valjev - Vrsta 10 MPa (100 barov)
Hydraulic fluid power -- Cylinder mounting dimensions -- 10 MPa (100 bar) series
Transmissions hydrauliques -- Dimensions d'interchangeabilité des vérins -- Série 10
MPa (100 bar)
Ta slovenski standard je istoveten z: ISO 10762:1997
ICS:
23.100.20 +LGUDYOLþQLYDOML Cylinders
SIST ISO 10762:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 10762:1998
---------------------- Page: 2 ----------------------
SIST ISO 10762:1998
INTERNATIONAL ISO
STANDARD 10762
First edition
1997-12-01
Hydraulic fluid power — Cylinder mounting
dimensions — 10 MPa (100 bar) series
Transmissions hydrauliques — Dimensions d'interchangeabilité des
vérins — Série 10 MPa (100 bar)
A
Reference number
ISO 10762:1997(E)
---------------------- Page: 3 ----------------------
SIST ISO 10762:1998
ISO 10762:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 10762 was prepared by Technical Committee
ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders.
Annex A of this International Standard is for information only.
© ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
---------------------- Page: 4 ----------------------
SIST ISO 10762:1998
©
ISO ISO 10762:1997(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled
through a liquid under pressure within an enclosed circuit.
One component of such systems is the fluid power cylinder. This is a
device which converts power into linear mechanical force and motion. It
consists of a movable element, i.e. a piston and piston rod, operating
within a cylindrical bore.
iii
---------------------- Page: 5 ----------------------
SIST ISO 10762:1998
---------------------- Page: 6 ----------------------
SIST ISO 10762:1998
©
INTERNATIONAL STANDARD ISO ISO 10762:1997(E)
Hydraulic fluid power — Cylinder mounting dimensions —
10 MPa (100 bar) series
1 Scope
1)
This International Standard establishes mounting dimensions for cylinders for use at 10 MPa [100 bar ], as required
for interchangeability of these cylinders.
NOTE — This International Standard allows manufacturers of hydraulic equipment flexibility in the design of 10 MPa (100 bar)
cylinders and does not restrict technical development; however, it does provide basic guidelines.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 273:1979, Fasteners — Clearance holes for bolts and screws.
ISO 286-2:1988, ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for
holes and shafts.
2)
ISO 1179-1:— , Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with
elastomeric or metal-to-metal sealing — Part 1: Threaded ports.
ISO 3320:1987, Fluid power systems and components — Cylinder bores and piston rod diameters — Metric series.
ISO 4395:1978, Fluid power systems and components — Cylinders — Piston rod thread dimensions and types.
ISO 5598:1985, Fluid power systems and components — Vocabulary.
ISO 6149-1:1993, Connections for fluid power and general use — Ports and stud ends with ISO 261 threads and
O-ring sealing — Part 1: Ports with O-ring seal in truncated housing.
ISO 8133:1991, Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar) compact series — Accessory
mounting dimensions.
5 2
1) 1 bar = 0,1 MPa = 10 Pa; 1 MPa = 1 N/mm
2) To be published. (Revision, in part, of ISO 1179:1981)
1
---------------------- Page: 7 ----------------------
SIST ISO 10762:1998
©
ISO
ISO 10762:1997(E)
3 Definitions
For the purposes of this International Standard, the definitions given in ISO 5598 and the following definitions
apply.
3.1 cylinder: Device which converts fluid power into linear mechanical force and motion.
3.2 cylinder bore: Internal diameter of the cylinder body.
3.3 piston rod: Element which transmits mechanical force and motion from the piston.
3.4 mounting: Device by which a cylinder is fastened to its mating element.
4 Dimensions
Mounting dimensions for cylinders manufactured in accordance with this International Standard shall be as given in
figures 1 to 13 and tables 1 to 13. Most tolerances are in accordance with ISO 286-2.
5 Bore sizes
The following bore sizes in accordance with ISO 3320, in millimetres, are included in this series:
40 — 50 — 63 — 80 — 100 — 125 — 160 — 200
6 Mounting types
This International Standard includes the following mounting types which conform to ISO 6099:
ME5 — Rectangular flange, integral with head (see figure 3 and table 3)
ME6 — Cap, rectangular flange (see figure 4 and table 4)
MP1 — Cap, fixed clevis (see figure 5 and table 5)
MP3 — Cap, fixed eye (see figure 6 and table 6)
MP5 — Cap, fixed eye with spherical plain bearing (see figure 7 and table 7)
MS2 — Side lugs (see figure 8 and table 8)
MT1 — Head, integral trunnion (male) (see figure 9 and table 9)
MT4 — Intermediate, fixed or movable trunnion (male) (see figure 10 and table 10)
MX1 — Both ends, studs or tie rods extended (see figure 11 and table 11)
MX2 — Cap, studs or tie rods extended (see figure 12 and table 12)
MX3 — Head, studs or tie rods extended (see figure 13 and table 13)
7 Piston rod characteristics
7.1 This International Standard covers piston rods which have a shouldered male thread end (see figure 1 and
table 1 for basic dimensions).
7.2 For internally threaded rod ends, see ISO 4395.
2
---------------------- Page: 8 ----------------------
SIST ISO 10762:1998
©
ISO
ISO 10762:1997(E)
7.3 If other piston rod diameters or other piston rod threads are required, those specified in ISO 3320 and
ISO 4395 shall be used.
8 Identification statement (Reference to this International Standard)
Use the following statement in test reports, catalogues and sales literature when electing to comply with this
International Standard:
“Interchangeable mounting dimensions for 10 MPa (100 bar) cylinders are selected in accordance with
ISO 10762:1997, Hydraulic fluid power — Cylinder mounting dimensions — 10 M
...
NORME ISO
INTERNATIONALE 10762
Première édition
1997-12-01
Transmissions hydrauliques — Dimensions
d'interchangeabilité des vérins —
Série 10 MPa (100 bar)
Hydraulic fluid power — Cylinder mounting dimensions —
10 MPa (100 bar) series
A
Numéro de référence
ISO 10762:1997(F)
---------------------- Page: 1 ----------------------
ISO 10762:1997(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération
mondiale d'organismes nationaux de normalisation (comités membres de
l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une
étude a le droit de faire partie du comité technique créé à cet effet. Les
organisations internationales, gouvernementales et non gouvernemen-
tales, en liaison avec l'ISO participent également aux travaux. L'ISO colla-
bore étroitement avec la Commission électrotechnique internationale (CEI)
en ce qui concerne la normalisation électrotechnique.
Les projets de Normes internationales adoptés par les comités techniques
sont soumis aux comités membres pour vote. Leur publication comme
Normes internationales requiert l'approbation de 75 % au moins des
comités membres votants.
La Norme internationale ISO 10762 a été élaborée par le comité technique
ISO/TC 131, Transmissions hydrauliques et pneumatiques, sous-comité
SC 3, Vérins.
L'annexe A de la présente Norme internationale est donnée uniquement à
titre d'information.
© ISO 1997
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publi-
cation ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun pro-
cédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord
écrit de l'éditeur.
Organisation internationale de normalisation
Case postale 56 • CH-1211 Genève 20 • Suisse
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Imprimé en Suisse
ii
---------------------- Page: 2 ----------------------
©
ISO ISO 10762:1997(F)
Introduction
Dans les systèmes de transmissions hydrauliques, l'énergie est transmise
et commandée par l'intermédiaire d'un liquide sous pression circulant en
circuit fermé.
L'un des organes de ces systèmes de transmissions est le vérin
hydraulique. Un vérin est un appareil qui transforme l'énergie du fluide en
énergie mécanique agissant linéairement. Il est constitué d'un élément
mobile composé d'un piston et d'une tige de piston se déplaçant à
l'intérieur d'un alésage cylindrique.
iii
---------------------- Page: 3 ----------------------
©
NORME INTERNATIONALE ISO ISO 10762:1997(F)
Transmissions hydrauliques — Dimensions
d'interchangeabilité des vérins — Série 10 MPa (100 bar)
1 Domaine d'application
La présente Norme internationale prescrit les dimensions d'interchangeabilité des vérins hydrauliques destinés à
1)
être utilisés à 10 MPa [100 bar ].
NOTE — La présente Norme internationale laisse aux fabricants d'équipements hydrauliques toute latitude quant à la
conception des vérins 10 MPa (100 bar); elle ne restreint pas le progrès technique, tout en fixant des orientations générales de
base.
2 Références normatives
Les normes suivantes contiennent des dispositions qui, par suite de la référence qui en est faite, constituent des
dispositions valables pour la présente Norme internationale. Au moment de la publication, les éditions indiquées
étaient en vigueur. Toute norme est sujette à révision et les parties prenantes des accords fondés sur la présente
Norme internationale sont invitées à rechercher la possibilité d'appliquer les éditions les plus récentes des normes
indiquées ci-après. Les membres de la CEI et de l'ISO possèdent le registre des Normes internationales en vigueur
à un moment donné.
ISO 273:1979, Éléments de fixation — Trous de passage pour vis.
ISO 286-2:1988, Système ISO de tolérances et d'ajustements — Partie 2: Tables des degrés de tolérances
normalisés et des écarts limites des alésages et des arbres.
2)
ISO 1179-1:— , Raccordements pour applications générales et transmissions hydrauliques et pneumatiques —
Orifices et éléments mâles à filetage ISO 228-1 et joint en élastomère ou étanchéité métal sur métal — Partie 1:
Orifices filetés.
ISO 3320:1987, Transmissions hydrauliques et pneumatiques — Alésages des vérins et diamètres des tiges de
piston — Série métrique.
ISO 4395:1978, Transmissions hydrauliques et pneumatiques — Vérins — Dimensions et types de filetage des
tiges de piston.
ISO 5598:1985, Transmissions hydrauliques et pneumatiques — Vocabulaire.
5 2
1) 1 bar = 0,1 MPa = 10 Pa; 1 MPa = 1 N/mm
2) À publier. (Révision partielle de l'ISO 1179:1981)
1
---------------------- Page: 4 ----------------------
©
ISO
ISO 10762:1997(F)
ISO 6149-1:1993, Raccordement pour transmissions hydrauliques et pneumatiques et applications générales —
Orifices et éléments mâles à filetage ISO 261 et joint torique — Partie 1: Orifice à joint torique dans un logement
tronconique.
ISO 8133:1991, Transmissions hydrauliques — Vérins 16 MPa (160 bar) à simple tige, série compacte —
Dimensions d'interchangeabilité des accessoires.
3 Définitions
Pour les besoins de la présente Norme internationale, les définitions données dans l'ISO 5598 et les suivantes
s'appliquent.
3.1 vérin: Appareil qui transforme l'énergie du fluide en énergie mécanique agissant linéairement.
3.2 alésage du vérin: Diamètre intérieur du vérin.
3.3 tige de piston: Élément transmettant l'énergie mécanique et le mouvement du piston.
3.4 fixation: Dispositif permettant la fixation du vérin sur l'élément correspondant.
4 Dimensions
Les dimensions d'interchangeabilité des vérins fabriqués conformément à la présente Norme internationale doivent
être conformes aux figures 1 à 13 et aux tableaux 1 à 13. La plupart des tolérances sont en conformité avec
l'ISO 286-2.
5 Alésages
La présente Norme internationale comprend les alésages suivants, en millimètres, conformément à l'ISO 3320:
40 — 50 — 63 — 80 — 100 — 125 — 160 — 200
6 Modes de fixation
La présente Norme internationale comporte les modes de fixation suivants, conformément à l'ISO 6099:
ME5 — Tête rectangulaire (voir figure 3 et tableau 3)
ME6 — Fond rectangulaire (voir figure 4 et tableau 4)
MP1 — Chape arrière fixe (voir figure 5 et tableau 5)
MP3 — Tenon arrière fixe (voir figure 6 et tableau 6)
MP5 — Tenon arrière fixe avec rotule (voir figure 7 et tableau 7)
MS2 — Pattes sur côté (voir figure 8 et tableau 8)
MT1 — Tourillons mâles avant incorporés (voir figure 9 et tableau 9)
MT4 — Tourillons mâles intermédiaires, fixes ou déplaçables (voir figure 10 et tableau 10)
MX1 — Goujons ou tirants dépassant de chaque extrémité (voir figure 11 et tableau 11)
MX2 — Goujons ou tirants dépassant du fond (voir figure 12 et tableau 12)
MX3 — Goujons ou tirants dépassant de la tête (voir figure 13 et tableau 13)
2
---------------------- Page: 5 ----------------------
©
ISO
ISO 10762:1997(F)
7 Caractéristiques des tiges de piston
7.1 La présente Norme internationale prescrit les caractéristiques des tiges de piston ayant une extrémité avec
filetage mâle et épaulement (voir figure 1 et tableau 1 pour les dimensions de base).
7.2 En ce qui concerne les extrémités taraudées des tiges de piston, voir l'ISO 4395.
7.3 Si d'autres diamètres de tige de piston ou d'autres filetages de tige de piston sont requis, ceux prescrits dans
l'ISO 3320 et l'ISO 4395 doivent être utilisés.
8 Phrase d'identification (Référence à la présente Norme internationale)
Il est vivement recommandé aux fabricants qui ont choisi de se conformer à la présente Norme internationale
d'utiliser dans leurs rapports d'essai, catalogues et documentation commerciale, la phrase d'identification suivante:
«Dimensions d'interchangeabilité des vérins 10 MPa (100 bar) conformes à l'ISO 10762:1997, Transmissions
hydrauliques — Dimensions d'interchangeabilité des vérins — Série 10 MPa (100 bar).»
3
---------------------- Page: 6 ----------------------
©
ISO
ISO 10762:1997(F)
Figure 1 — Dimensions de base
Tableau 1 — Dimensions de base
Dimensions en millimètres
1) 2)
MM KK A E H
Alésage
max. max. max.
18 ou 28 M14 · 1,5 18
52 5
40
28 M20 · 1,5 28
22 ou 36 M16 · 1,5 22
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.