Hollow taper interface with flange contact surface — Part 3: Dimensions of shanks for stationary tools

ISO 12164-3:2014 specifies dimensions for hollow taper shanks with flange contact surface (HSK) to be applied to machine tools (e.g. turning machines, turning-mill machines). A range of shank sizes is specified. Specified is the shank of type T. It incorporates a grooved flange to enable automatic tool exchange. The tools can also be exchanged manually via a hole in the shank taper. The torque is transmitted at the tail end of the shank through keys as well as friction.

Interfaces à cône creux-face — Partie 3: Dimensions des queues pour outils non rotatifs

l'ISO 12164-3:2014 spécifie les dimensions des queues à cône creux (HSK) à utiliser sur des machines-outils (par exemple machines de tournage, machines de tournage-fraisage). Une gamme de dimensions de queues est spécifiée. Elle spécifie les queues de type T. Elles comprennent une collerette rainurée pour le changement automatique de l'outil. Les outils peuvent aussi être changés manuellement via un trou dans la queue conique. Le couple est transmis à l'extrémité de la queue au moyen de rainures d'entraînement ou par friction.

General Information

Status
Published
Publication Date
07-Dec-2014
Current Stage
9092 - International Standard to be revised
Completion Date
13-Feb-2019
Ref Project

Relations

Buy Standard

Standard
ISO 12164-3:2014 - Hollow taper interface with flange contact surface
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 12164-3:2014 - Interfaces a cône creux-face
French language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 12164-3
Second edition
2014-12-15
Hollow taper interface with flange
contact surface —
Part 3:
Dimensions of shanks for stationary
tools
Interfaces à cône creux-face —
Partie 3: Dimensions des queues pour outils non rotatifs
Reference number
ISO 12164-3:2014(E)
ISO 2014
---------------------- Page: 1 ----------------------
ISO 12164-3:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 12164-3:2014(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Dimensions ................................................................................................................................................................................................................. 1

3.1 General ........................................................................................................................................................................................................... 1

3.2 Hollow taper shank, type T .......................................................................................................................................................... 1

4 Design .............................................................................................................................................................................................................................. 6

4.1 Data chip hole .......................................................................................................................................................................................... 6

4.2 Orientation notch .................................................................................................................................................................................. 6

4.3 Clamping forces ...................................................................................................................................................................................... 6

4.4 Hole for manual clamping ............................................................................................................................................................. 6

5 Designation ................................................................................................................................................................................................................ 6

Annex A (normative) Details of groove .............................................................................................................................................................. 7

Annex B (informative) Recommendations for use and application ..................................................................................... 9

Bibliography .............................................................................................................................................................................................................................10

© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 12164-3:2014(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any

patent rights identified during the development of the document will be in the Introduction and/or on

the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers

to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 29, Small tools.

This second edition cancels and replaces the first edition (ISO 12164-3:2008), Figure 1 and Table 1 of

which have been technically revised.

ISO 12164 consists of the following parts, under the general title Hollow taper interface with flange

contact surface:
— Part 1: Shanks — Dimensions
— Part 2: Receivers — Dimensions
— Part 3: Dimensions of shanks for stationary tools
— Part 4: Dimensions of receivers for stationary tools
iv © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 12164-3:2014(E)
Hollow taper interface with flange contact surface —
Part 3:
Dimensions of shanks for stationary tools
1 Scope

This part of ISO 12164 specifies dimensions for hollow taper shanks with flange contact surface (HSK)

to be applied to machine tools (e.g. turning machines, turning-mill machines). A range of shank sizes is

specified.

This part of ISO 12164 specifies the shank of type T. It incorporates a grooved flange to enable automatic

tool exchange. The tools can also be exchanged manually via a hole in the shank taper.

The torque is transmitted at the tail end of the shank through keys as well as friction.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

ISO 1101, Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form,

orientation, location and run-out

ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual

tolerance indications

ISO 3040, Geometrical product specifications (GPS) — Dimensioning and tolerancing — Cones

3 Dimensions
3.1 General
Dimensions of hollow taper
...

NORME ISO
INTERNATIONALE 12164-3
Deuxième édition
2014-12-15
Interfaces à cône creux-face —
Partie 3:
Dimensions des queues pour outils
non rotatifs
Hollow taper interface with flange contact surface —
Part 3: Dimensions of shanks for stationary tools
Numéro de référence
ISO 12164-3:2014(F)
ISO 2014
---------------------- Page: 1 ----------------------
ISO 12164-3:2014(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2014

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée

sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur

l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à

l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2014 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 12164-3:2014(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Dimensions ................................................................................................................................................................................................................. 1

3.1 Généralités .................................................................................................................................................................................................. 1

3.2 Queue à cône creux-face, type T ............................................................................................................................................... 1

4 Conception .................................................................................................................................................................................................................. 6

4.1 Logement de puce ................................................................................................................................................................................ 6

4.2 Encoche d’orientation ....................................................................................................................................................................... 6

4.3 Effort de serrage .................................................................................................................................................................................... 6

4.4 Trou pour serrage manuel ............................................................................................................................................................ 6

5 Désignation ................................................................................................................................................................................................................ 6

Annexe A (normative) Annexe ADétails de la gorge ............................................................................................................................. 7

Annexe B (informative) Annexe BRecommandations pour l’utilisation et l’application ...............................9

Bibliographie ...........................................................................................................................................................................................................................10

© ISO 2014 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 12164-3:2014(F)
Avant-propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes

nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est

en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.

L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui concerne

la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents

critères d’approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.

iso.org/directives).

L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de

droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les

références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration

du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de brevets reçues par

l’ISO (voir www.iso.org/patents).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à l’évaluation

de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes de l’OMC

concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Foreword - Supplementary

information.

Le comité chargé de l’élaboration du présent document est l’ISO/TC 29, Petit outillage.

Cette seconde édition annule et remplace la première édition (ISO 12164-3:2008), dont Figure 1 et le

Tableau 1 ont fait l’objet d’une révision technique.

L’ISO 12164 comprend les parties suivantes, présentées sous le titre général Interfaces à cône creux-face::

— Partie 1: Queues - Dimensions
— Partie 2: Nez de broches - Dimensions
— Partie 3: Dimensions des queues pour outils non rotatifs
— Partie 4: Dimensions des nez de broche pour outils non rotatifs
iv © ISO 2014 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 12164-3:2014(F)
Interfaces à cône creux-face —
Partie 3:
Dimensions des queues pour outils non rotatifs
1 Domaine d’application

La présente partie de l’ISO 12164 spécifie les dimensions des queues à cône creux (HSK) à utiliser sur

des machines-outils (par exemple machines de tournage, machines de tournage-fraisage). Une gamme

de dimensions de queues est spécifiée.

La présente partie de l’ISO 12164 spécifie les queues de type T. Elles comprennent une collerette rainurée

pour le changement automatique de l’outil. Les outils peuvent aussi être changés manuellement via un

trou dans la queue conique.

Le couple est transmis à l’extrémité de la queue au moyen de rainures d’entraînement ou par friction.

2 Références normatives

Les documents de référence suivants, en tout ou partie, sont référencés de manière normative dans le

présent document et sont indispensables à son application. Pour les références datées, seule l’édition

citée s’applique. Pour les références non datées, la dernière édition du document de référence s’applique

(y compris les éventuels amendements).

ISO 1101, Spécification géométrique des produits (GPS) — Tolérancement géométrique — Tolérancement

de forme, orientation, position et battement

ISO 2768-1, Tolérances générales — Partie 1: Tolérances pour dimensions linéaires et angulaires non

affectées de tolérances individuelles

ISO 3040, Spécification géométrique des produits (GPS) — Cotation et tolérancement — Cônes

3 Dimensions
3.1 Généralités

Les dimensions des queues à cône creux-face, de type T, pour outils non rotatifs sont spécifiées à la

Figure 1, dans le Tableau 1, à l’Annexe A et à l’Annexe B. Les détails non spécifiés à Figure 1 doivent être

choisis convenablement. Le tolérance
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.