ISO/DIS 16559
(Main)Solid biofuels -- Terminology, definitions and descriptions
Solid biofuels -- Terminology, definitions and descriptions
Biocombustibles solides -- Terminologie, définitions et descriptions
General Information
RELATIONS
Buy Standard
Standards Content (sample)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 16559
ISO/TC 238 Secretariat: SIS
Voting begins on: Voting terminates on:
2020-03-24 2020-06-16
Solid biofuels — Terminology, definitions and descriptions
Biocombustibles solides — Terminologie, définitions et descriptions
ICS: 01.040.75; 27.190; 75.160.40
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 16559:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 1 ----------------------
ISO/DIS 16559:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 16559:2020(E)
Contents Page
Foreword ........................................................................................................................................................................................................................................iv
Introduction ..................................................................................................................................................................................................................................v
1 Scope ................................................................................................................................................................................................................................. 1
2 Normative references ...................................................................................................................................................................................... 1
3 Principle ........................................................................................................................................................................................................................ 1
4 Terms and definitions ..................................................................................................................................................................................... 2
Annex A (informative) Scheme of sample hierarchy .........................................................................................................................29
© ISO 2020 – All rights reserved iii---------------------- Page: 3 ----------------------
ISO/DIS 16559:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.ISO 16559 was prepared by ISO Technical Committee TC 238, Solid biofuels, in collaboration with the
European Committee for Standardization (CEN) Technical Committee CEN/TC 335, Solid biofuels, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 16559:2014), which has been technically
revised.The main changes compared to the previous edition are as follows:
— Terms an definitions updated in the whole document and
— Annex A "Scheme of sample hierarchy "added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.iv © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/DIS 16559:2020(E)
Introduction
This International Standard has been written in accordance with ISO 10241. This International Standard
is based on European standard EN 14588:2010 as well as on approved national standards and manuals.
Some of the terms included in this International Standard are only used in particular countries.
In this International Standard instead of the legal definition waste the technical terms residue, and by-
product are used to describe co-products from forestry and arboriculture, agriculture and horticulture,
and aquaculture as well as related industries. The terms and definitions are harmonized as far as
possible with the current language used in management as well as in regulatory activities.
© ISO 2020 – All rights reserved v---------------------- Page: 5 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 16559:2020(E)
Solid biofuels — Terminology, definitions and descriptions
1 Scope
This international standard determines the terminology and definitions for solid biofuels. According to
the scope of the ISO/TC 238 this standard only includes raw and processed material originating from
— forestry and arboriculture,— agriculture and horticulture,
— aquaculture.
NOTE 1 Raw and processed material includes woody, herbaceous, fruit and aquatic biomass from the sectors
mentioned above.NOTE 2 Chemically treated material does not include halogenated organic compounds or heavy metals at
levels higher than those in typical virgin material values or higher than typical values of the country of origin.
Materials originating from different recycling processes of end-of-life-products are not within the scope
but relevant terms are included for information. Areas covered by ISO/TC 28/SC 7 “Liquid biofuels”,
ISO/TC 193 “Natural gas” and ISO/TC 300 “Solid recovered fuels” are excluded.Other standards with a different scope than this International Standard may have different definitions
than this standard.2 Normative references
There are no normative references in this document.
3 Principle
This International Standard only contains terms used to describe solid biofuels within the scope of
ISO/TC 238, see Figure 1.Figure 1 — ISO/TC 238 within the biomass-biofuel-bioenergy field
© ISO 2020 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO/DIS 16559:2020(E)
Solid biofuels are produced from different sources, which are defined within the scope of ISO/TC 238
“Solid Biofuels”. Terms and definitions are categorised in a logical structure based on the fact that solid
biofuels are produced from different sources and that solid biofuels are used to produce bioenergy:
— origin and source of solid biofuels in the overall supply chain;— the different traded forms as well as the different forms of biofuels produced within the preparation
processes;— the most relevant solid biofuel properties and terms of sampling and testing as well as classification
and specification;— the description of the solid biofuels itself as well as their handling and processing given in the same
structure as the biomass sources;— bioenergy as the result of solid biofuel conversion.
Appropriate terms for sampling and testing as well as classification and specification of properties
have to be defined and described together with the category source/origin, type and properties of solid
biofuels. The necessity of terms defined in this International Technical Standard is in many cases based
on the classification system of solid biofuels given in ISO 17225-1, in which the classification of solid
biofuels is specified in more detail.4 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http:// www .iso .org/ obp— IEC Electropedia: available at http:// www .electropedia .org/
4.1
absorption
phenomenon whereby atoms, ions, or molecules from a gas, liquid, or dissolved solid permeates or is
dissolved by a liquid or solid (the absorbent)Note 1 to entry: Adsorption is a surface-based process while absorption involves the whole volume of the material.
[SOURCE: ISO 18757:2003, normative text summarised as term and definition]4.2
adsorption
phenomenon whereby atoms, ions, or molecules from a gas, liquid, or dissolved solid adheres to a
surface whereby the process creates a film of the adsorbate on the surface of the adsorbent
[SOURCE: ISO 18757:2003, 3.1]4.3
additive
material which has been intentionally introduced into the fuel feedstock to improve quality of fuel (e.g.
combustion properties or durability), to reduce emissions or to make production more efficient
Note 1 to entry: Trace amounts of e.g. grease or other lubricants that are introduced into the fuel processing
stream as part of normal mill operations are not considered as additives.[SOURCE: ISO 17225-2:2014, 3.2]
2 © ISO 2020 – All rights reserved
---------------------- Page: 7 ----------------------
ISO/DIS 16559:2020(E)
4.4
agrofuels
biofuels obtained from energy crops and/or agricultural by-products (agricultural residues)
[SOURCE: FAO unified bioenergy terminology (UBET)]4.5
air dried
condition in which the solid biofuel has been dried in air to equilibrium moisture content
[SOURCE: ISO 1213-2:1992 3.5, modified – with regard to solid biofuels ]4.6
angle of repose
critical angle of repose
steepest angle of descent of a stock pile measured in degrees of the slope of material relative to the
horizontal plane when granular material on the slope face is on the verge of sliding
Note 1 to entry: The angle of repose is normally a few degrees lower than the angle of drain.
[SOURCE: ISO 4324:1977, 3]4.7
angle of drain
steepest angle of descent within a silo or a hopper when material is withdrawn from the bottom
measured in degrees of the slope of material relative to the horizontal plane when granular material on
the slope face is on the verge of slidingNote 1 to entry: The angle of drain is normally a few degrees higher than the angle of repose.
4.8animal biomass
biomass obtained from livestock
4.9
animal by-products
animal residues
agricultural by-products (or agricultural residues) obtained from livestock operations
Note 1 to entry: It includes among others solid excreta of animals.4.10
aquatic biomass
biomass from hydrophytic plants or hydrophytes, which are plants that have adapted to living in or on
aquatic environments[SOURCE: ISO 17225-1:2014, normative text summarised as term and definition]
4.11
as determined
as analysed
reference moisture content of the material at the moment of analysis/determination
Note 1 to entry: The abbreviation of “as determined” is “ad”. It is used as a subscript (e.g. A is equivalent to ash
content at the moisture content at the time of determination).[SOURCE: ISO 1213-2:1992, text summarised as term and definition with regard to solid biofuels]
© ISO 2020 – All rights reserved 3---------------------- Page: 8 ----------------------
ISO/DIS 16559:2020(E)
4.12
as received
as delivered
calculation basis for a material in the delivery state
Note 1 to entry: The abbreviation of “as received” is “ar”.
[SOURCE: ISO 15357:2011, 3.1, modified – "at delivery" changed to " in the delivery state"]
4.13ash
ash content
total ash
mass of inorganic residue remaining after complete combustion of a fuel under specified conditions,
typically expressed as a percentage of the mass of dry matter in fuelNote 1 to entry: See also ash fusibility, natural ash, extraneous ash.
Note 2 to entry: Depending on the combustion efficiency the ash may contain combustibles.
Note 3 to entry: If a complete combustion is realised ash contains only inorganic, non-combustible components.
[SOURCE: ISO 1213-2:1992, modified – text summarised as term and definition with regard to solid
biofuels]4.14
ash deformation temperature
temperature at which first signs of rounding due to melting of the edges of the ash test piece occur
4.15ash flow temperature
temperature at which the ash is spread out over the supporting tile in a layer, the height of which is half
of the height of the test piece at the ash hemisphere temperature4.16
ash fusibility
ash melting behaviour
characteristic physical state of the ash obtained by heating under specific conditions
Note 1 to entry: Ash fusibility is determined under either oxidising or reducing conditions.
Note 2 to entry: See also ash deformation temperature, ash flow temperature, ash hemisphere temperature and ash
shrinkage starting temperature.4.17
ash hemisphere temperature
temperature at which the height of a test piece, prepared from ash by a specific procedure, is equal to
half the width of the base, and its shape becomes approximately hemispherical4.18
ash shrinkage starting temperature
SST
temperature at which shrinking of the test piece occurs
Note 1 to entry: This temperature is defined as when the area of the test piece falls below 95 % of the original
test piece area at 550 °C.4 © ISO 2020 – All rights reserved
---------------------- Page: 9 ----------------------
ISO/DIS 16559:2020(E)
4.19
bag weight
weight of the fuel including the bag
4.20
baled biofuel
bale
solid biofuel which has been compressed and bound to keep its shape and density
EXAMPLE Straw bales, bales of energy grass, bales of logging residues.
4.21
bark
organic cellular tissue which is formed by taller plants (trees, bushes) on the outside of the growth zone
(cambium) as a shell for the wooden body4.22
basic density
ratio of the mass on dry basis and the solid volume on green basis
4.23
biobased
derived from biomass
[SOURCE: EN 16575:2013, 2.1]
4.24
biobased content
fraction of a fuel that is derived from biomass
Note 1 to entry: Normally expressed as a percentage of the total mass of the product.
[SOURCE: EN 16575:2013, 2.4, modified – "product" changed to "fuel"]4.25
biobased product
biobased industrial product
bioproduct
product wholly or partly derived from biomass
Note 1 to entry: The biobased product is normally characterized by the biobased carbon content or the biobased
content.[SOURCE: EN 16575:2013, 2.5]
4.26
bioenergy
energy derived from biomass
4.27
biofuel
solid, liquid or gaseous fuel produced directly or indirectly from biomass
4.28
biofuel blend
biofuel resulting from intentionally mixing of different biofuels
EXAMPLE Straw or energy grass with wood, dried biosludge with bark.
© ISO 2020 – All rights reserved 5
---------------------- Page: 10 ----------------------
ISO/DIS 16559:2020(E)
4.29
biofuel briquette
densified biofuel made with or without additives in pre-determined geometric form with at least two
diameters of more than 25 mm, produced by compressing biomass4.30
biofuel mixture
biofuel resulting from natural or unintentional mixing of different biofuels and/or different types of
biomass4.31
biofuel pellet
densified biofuel made with or without additives usually with a cylindrical form, random length typically
5 mm to 40 mm and diameter up to 25 mm and broken ends, produced by compressing biomass
Note 1 to entry: Usually the biomass has been milled before densification.Note 2 to entry: See also non-woody pellet, wood pellet and pellet from thermally treated biomass.
4.32biomass
material of biological origin excluding material embedded in geological formations and/or fossilized
Note 1 to entry: Biomass is organic material that is plant or animal based, including but not limited to dedicated
energy crops, agricultural crops and trees, food, feed and fibre crop residues, aquatic plants, algae, forestry and
wood residues, agricultural wastes, processing by-products and other non fossil organic matters.
Note 2 to entry: See also herbaceous biomass, fruit biomass, and woody biomass.4.33
biomass by-product
a secondary product which is made incidentally during the production of something else
EXAMPLE Sawdust when sawing timber.4.34
biomass residue
biomass from well-defined side-streams from forestry, agriculture, aquaculture and related industrial
operationsEXAMPLE Olive cake after pressing of oil, logging residues.
4.35
biomass resource owner
body or enterprise with the right to exploit the biomass resources
Note 1 to entry: The biomass resource owner can be a land or forest owner, a company etc.
4.36biomethane
methane produced from biomass (e.g. solid biofuels)
Note 1 to entry: Biomethane is not a solid biofuel. The term is included for information only.
4.37biosludge
sludge formed in the aeration basin during biological waste water treatment or biological treatment
process and separated by sedimentation or flotationNote 1 to entry: Biosludge has to be treated for the transformation into solid biomass.
6 © ISO 2020 – All rights reserved---------------------- Page: 11 ----------------------
ISO/DIS 16559:2020(E)
4.38
black liquor
a fluid containing lignin removed from the wood in the pulping process
Note 1 to entry: Black liquor contains also pulping chemicals.
Note 2 to entry: Black liquor is not a solid biofuel. The term is included for information only.
4.39bridging
arching
tendency of particles to form a stable arch across an opening and hindering flow
[SOURCE: ISO/DIS 21637:2019, 3.8]
4.40
briquette from thermally treated biomass
biofuel briquette made from thermally treated biomass
4.41
bulk density
mass of a portion of a particulate matter divided by the volume of the container which is filled by that
portion under specific conditions[SOURCE: ISO 1213-2:1992, 3.21, modified – with regard to solid biofuels]
4.42
bulk volume
loose volume
volume of a material including space between the particles
4.43
bundled biofuel
bundle
solid biofuels which have been bound together and where there is a lengthwise orientation of the
materialEXAMPLE Bundles of short rotation coppice, logging residues or small trees,
4.44
calorific value
heating value
energy amount per unit mass released on complete combustion
Note 1 to entry: See also gross calorific value, energy density, net calorific value.
4.45cereal crops
annual crops grown with the main purpose of using the seed for food production
Note 1 to entry: Some cereal crops can be used as a solid biofuel.
EXAMPLE Barley, wheat, rye, oat.
© ISO 2020 – All rights reserved 7
---------------------- Page: 12 ----------------------
ISO/DIS 16559:2020(E)
4.46
certified reference material
CRM
reference material of which one or more property values are certified by a technically valid procedure,
accompanied by or traceable to a certificate or other documentation which is issued by a certifying body
[SOURCE: ISO 16967, 3.2, modified – definition updated]4.47
charcoal
biochar
biocarbon
biocoke
biocoal
solid biofuel derived from carbonization, distillation or pyrolysis of biomass
[SOURCE: ANSI/ASABE S593]
4.48
chemical treatment
any treatment with chemicals other than air, water or heat
[SOURCE: ISO 17225-7:2014, 3.3]
4.49
chopped straw
straw which has been cut into small pieces
4.50
chunkwood
wood cut with sharp cutting devices where most of the material have typical particle lengths of 50
to 150 mmNote 1 to entry: Chunkwood is substantially longer and coarser than wood chips.
4.51
coke
the solid residue of impure carbon obtained from carbon rich feedstock after removal of volatile material
by destructive distillation[SOURCE: ANSI/ASABE S593-2006]
4.52
combined sample
sample consisting of all the increments taken from a lot or a sub-lot
Note 1 to entry: The increments may be reduced by division before being added to the combined sample.
Note 2 to entry: See also annex A.[SOURCE: EN 14780:2011, 3.1, changed – Note 2 added]
4.53
complete tree
tree, including branches and root system
Note 1 to entry: See also whole tree.
8 © ISO 2020 – All rights reserved
---------------------- Page: 13 ----------------------
ISO/DIS 16559:2020(E)
4.54
contamination
occurrence of any undesirable matter such as chemical, physical and/or microbiological matter in
the product[SOURCE: ISO 22716:2007, 2.10]
4.55
co-product
any of two or more products coming from the same unit process or product system
[SOURCE: ISO 14040:2006, 3.10]
4.56
critical control point
quality control point
CCP
point within or between processes at which relevant properties can be most readily assessed; quality
control points also offer the greatest potential for quality improvement4.57
cross-cut ends
short pieces of woody biomass which occur when the ends of logs or sawn timber are cross cut off, with
or without bark4.58
customer
organisation or person that receives a product
[SOURCE: ISO 9000:2005, 3.3.5]
4.59
cutter chips
wood chips made as a by-product of the wood processing industry, with or without bark
4.60deflagration
violent event describing subsonic combustion propagating by means of hot burning material (usually
dust) heating the next layer of cold material and igniting it in consecutive sequence
Note 1 to entry: The process can be characterized as an exploding fire whereby the burning material partly
deposits on surfaces in its path and causing significant damage and injuries.[SOURCE: EN 13857-1:2003, 2.13, modified – with regard to solid biofuels]
4.61
deflagration index
measure in bar meter per second and a product of the pressure rate and propagation of an explosion as
established by testing standards4.62
delivery agreement
contract for fuel trade, which specifies e.g. origin and source, quality and quantity of the fuel, as well as
delivery terms4.63
delivery lot
solid biofuel batch on which the essential quality requirements for solid biofuel are focused
Note 1 to entry: The delivery lot can be an individual delivery lot, which is an agreed quantity of solid biofuel (e.g. a
package, shipload or truck load), or continuous delivery, where several loads are delivered to the end-user during
an agreed period of time (usually daily or weekly delivery).© ISO 2020 – All rights reserved 9
---------------------- Page: 14 ----------------------
ISO/DIS 16559:2020(E)
Note 2 to entry: In continuous delivery, the delivery lot is the amount of solid biofuel delivered during a specified
period of time, e.g. 24 h, unless otherwise agreed by supplier and end-user. If the delivery lot in continuous delivery
is more than 1,500 to 2,000 m in 24 h, it is recommended that it should be divided into two or more individual lots.
4.64demolition wood
used wood arising from demolition of buildings or civil engineering installations
[SOURCE: EN 13965-1:2004, 505, modified – with regard to solid biofuels, e.g. "waste" to "(used) wood"]
4.65densified biofuel
compressed biofuel
solid biofuel made by mechanically compressing biomass or thermally treated biomass to mould the solid
biofuel into a specific size and shape such as cubes, pressed logs, biofuel pellets or biofuel briquettes
Note 1 to entry: See also biofuel briquette and biofuel pellet.4.66
density
ratio of mass to volume or ratio of energy content to volume
Note 1 to entry: It must always be stated whether the density refers to the density of individual particles or to the
bulk density of the material and whether the mass of water in the material is included.
Note 2 to entry: See also bulk density, particle density and energy density4.67
desorption
phenomenon whereby a substance is released from or through a surface
Note 1 to entry: The process is the opposite of absorption and adsorption.
4.68
detonation
violent event generated by sudden expansion of gas in to a supersonic shock wave (molecular speed
higher than the speed of sound) not followed by fire[SOURCE: EN 13857-1:2003, 2.19, modified – with regard to solid biofuels]
4.69
devolatilization
process (usually pyrolysis or gasification) whereby volatile matter is removed from carbon rich
feedstock (e.g. biomass)[SOURCE: ANSI/ASABE S593]
4.70
dry ash free
dry ash free basis
daf
calculation basis in which the solid biofuel is considered free from moisture and inorganic matter
Note 1 to entry: The abbreviation of “dry ash free” is “daf”.4.71
dry
dry basis
calculation basis in which the solid biofuel is considered free from moisture
Note 1 to entry: The abbreviation of “dry basis” is “d”.
10 © ISO 2020 – All rights reserved
---------------------- Page: 15 ----------------------
ISO/DIS 16559:2020(E)
4.72
dry matter
material remaining after removal of moisture under specific conditions
4.73
dry matter content
portion of dry matter in the total material on mass basis
Note 1 to entry: Expressed as a percentage of the total mass of the solid biofuel.
4.74dust
fragmented material of small size passing a 500 µm sieve caused by a non-intentional process
Note 1 to entry: It is opposed to fuel powder which is intentionally manufactured to size.
4.75edgings
parts of woody biomass which occur when trimming sawn timber and which show a remainder of the
original rounded surface of the tree, with or without bark4.76
end-user
consumer (private person, enterprise, utility etc.) using biofuel
4.77
energy crops
woody or herbaceous crops grown and harvested specifically for their fuel value
Note 1 to entry: See also energy forest trees, energy grass.
4.78
energy density
ratio of net energy content and bulk volume
Note 1 to entry: The energy density is calculated using the net calorific value determined and the bulk density.
4.79energy forest trees
woody biomass grown specifically for its fuel value in medium to long rotation forestry
4.80energy grain
grain used for energy purpose
4.81
energy grass
herbaceous energy crop
EXAMPLE Sugarcane, Miscanthus, Reed canary grass.
4.82
explosibility
propensity by gaseous, liquid or solid material to ignite and violently transform to high pressure gas
while emitting sound and light and normally followed by fire© ISO 2020 – All rights reserved 11
---------------------- Page: 16 ----------------------
ISO/DIS 16559:2020(E)
4.83
explosion (primary and secondary)
violent event emitting sound and light immediately followed by fire
Note 1 to entry: An initial explosion followed by fire may dislodge dust deposited on beams, floor, machinery etc.
and ignite this material resulting in a secondary explosion, usually a few seconds after the first explosion.
Note 2 to entry: Thermal energy is transferred from the first to the second explosion through deflagration.
[SOURCE: EN 16256-1:2012, 2.9, modified – with regard to solid biofuels, e.g. Notes added]
4.84extraneous ash
ash from contaminants entering the material at harvest, logging, treatment, transport, storage etc
4.85extraneous material
foreign matternon-biomass material, which has entered the fuel, e.g. plastic, metal or stone
Note 1 to entry: See also impurity.Note 2 to entry: See also heavy extraneous material.
4.86
feedstock
material that is further processed for conversion to bioenergy, biofuel and/or biobased products
4.87fibre saturation point
FSP
the moisture content of woody material at which only the cell walls are completely saturated (all bound
water) but no free water exists in the cell lumens – typically about 30 % total moisture (on dry basis)
Note 1 to entry: Below the fibre saturation point the physical and mechanical properties of wood begin to change
as a function of moisture content.4.88
fibre sludge
sludge formed in the sedimentation basin as a part of the waste water treatment process in a pulp and
paper mill and separated by sedimentation or flotationNote 1 to entry: The
...
PROJET DE NORME INTERNATIONALE
ISO/DIS 16559
ISO/TC 238 Secrétariat: SIS
Début de vote: Vote clos le:
2020-03-24 2020-06-16
Biocombustibles solides — Terminologie, définitions et
descriptions
Solid biofuels — Terminology, definitions and descriptions
ICS: 01.040.75; 27.190; 75.160.40
CE DOCUMENT EST UN PROJET DIFFUSÉ POUR
OBSERVATIONS ET APPROBATION. IL EST DONC
SUSCEPTIBLE DE MODIFICATION ET NE PEUT
Le présent document est distribué tel qu’il est parvenu du secrétariat du comité.
ÊTRE CITÉ COMME NORME INTERNATIONALEAVANT SA PUBLICATION EN TANT QUE TELLE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES
FINS INDUSTRIELLES, TECHNOLOGIQUES ET
COMMERCIALES, AINSI QUE DU POINT DE VUE TRAITEMENT PARALLÈLE ISO/CEN
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR
POSSIBILITÉ DE DEVENIR DES NORMES
POUVANT SERVIR DE RÉFÉRENCE DANS LA
RÉGLEMENTATION NATIONALE.
Numéro de référence
LES DESTINATAIRES DU PRÉSENT PROJET
ISO/DIS 16559:2020(F)
SONT INVITÉS À PRÉSENTER, AVEC LEURS
OBSERVATIONS, NOTIFICATION DES DROITS
DE PROPRIÉTÉ DONT ILS AURAIENT
ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE. ISO 2020
---------------------- Page: 1 ----------------------
ISO/DIS 16559:2020(F)
ISO/DIS 16559:2020(F)
Sommaire Page
Avant-propos .................................................................................................................................................................. iv
Introduction .................................................................................................................................................................... v
1 Domaine d'application .................................................................................................................................. 1
2 Références normatives .................................................................................................................................. 1
3 Principe ............................................................................................................................................................... 1
4 Termes et définitions ..................................................................................................................................... 2
(informative) Schéma de hiérarchie des échantillons ............................................................. 36
DOCUMENT PROTÉGÉ PAR COPYRIGHT© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright officeCase postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
̹ʹͲʹͲ–‘—•†”‘‹–•”±•‡”˜±•
Tél.: +41 22 749 01 11 ‹‹‹
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Website: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO/DIS 16559:2020(F)
Sommaire Page
Avant-propos .................................................................................................................................................................. iv
Introduction .................................................................................................................................................................... v
1 Domaine d'application .................................................................................................................................. 1
2 Références normatives .................................................................................................................................. 1
3 Principe ............................................................................................................................................................... 1
4 Termes et définitions ..................................................................................................................................... 2
(informative) Schéma de hiérarchie des échantillons ............................................................. 36
© ISO 2020 – Tous droits réservésiii
---------------------- Page: 3 ----------------------
ISO/DIS 16559:2020(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement
avec la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation
électrotechnique.Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l'élaboration
du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de brevets reçues par
l’ISO (voir www.iso.org/brevets).Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un
engagement.Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC) voir le lien suivant : www.iso.org/iso/fr/avant-propos.L’ISO 16559 a été élaborée par le comité technique TC 238, Biocombustibles solides, en collaboration avec
le Comité européen de normalisation (CEN), comité technique CEN/TC 335, Biocombustibles solides,
conformément à l'Accord de coopération technique entre l'ISO et le CEN (Accord de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 16559:2014), qui a fait l’objet d’une
révision technique.Les principales modifications par rapport à l'édition précédente sont les suivantes :
— termes et définitions mis à jour dans l’intégralité du document, et— ajout de l’Annexe A « Schéma de la hiérarchie d’échantillons ».
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/fr/members.html.© ISO 2020 – Tous droits réservés
---------------------- Page: 4 ----------------------
ISO/DIS 16559:2020(F)
Introduction
La présente Norme internationale a été rédigée conformément à l'ISO 10241. La présente Norme
internationale est basée sur la Norme européenne EN 14588:2010 et sur les normes nationales et manuels
approuvés. Quelques-uns des termes inclus dans la présente Norme internationale ne sont utilisés que
dans certains pays.Dans la présente Norme internationale, au lieu de la définition légale déchet, les termes techniques
sous-produit et produit dérivé sont utilisés pour désigner les coproduits de la sylviculture et de
l'arboriculture, de l'agriculture et de l'horticulture, de l'aquaculture et des branches d'activité connexes.
Les termes et les définitions ont été harmonisés autant que possible avec le vocabulaire employé à la fois
dans le domaine de la gestion et dans le cadre des activités de réglementation.© ISO 2020 – Tous droits réservés
---------------------- Page: 5 ----------------------
PROJET DE NORME INTERNATIONALE ISO/DIS 16559:2020(F)
Biocombustibles solides — Terminologie, définitions et
descriptions
1 Domaine d'application
La présente Norme internationale établit la terminologie et les définitions liées aux biocombustibles
solides. D'après le domaine d'application de l'ISO/TC 238, la présente norme ne couvre que les matières
premières et les matières issues de processus provenant de :— la sylviculture et l'arboriculture ;
— l'agriculture et l'horticulture ;
— l'aquaculture.
NOTE 1 Les matières premières brutes et transformées comprennent les biomasses ligneuse, herbacée, fruitière
et aquatique provenant des secteurs mentionnés ci-dessus.NOTE 2 Un matériau traité chimiquement n’inclut pas de composés organiques halogénés ou de métaux lourds à
des valeurs supérieures à celles de matériaux vierges types ou supérieures à des valeurs typiques du pays
d’origine.Les matériaux provenant de différents processus de recyclage de produits en fin de vie ne relèvent pas
du domaine d'application de la présente norme, mais les termes qui s'y rapportent sont inclus à titre
d'information. Les domaines couverts par l’ISO/TC 28/SC 7 « Biocombustibles liquides », l'ISO/TC193
« Gaz naturel » et l’ISO/TC 300 « Combustibles solides de récupération » sont exclus.
D'autres normes dont le domaine d'application est différent de celui de la présente Norme
internationale peuvent proposer des définitions différentes de celles données dans la présente norme.
2 Références normativesLe présent document ne contient aucune référence normative.
3 Principe
La présente Norme internationale ne contient que des termes utilisés pour la description des
biocombustibles solides dans les limites du domaine d'application de l'ISO/TC 238, voir Figure 1.
© ISO 2020 – Tous droits réservés---------------------- Page: 6 ----------------------
ISO/DIS 16559:2020(F)
Figure 1 — Intégration de l'ISO/TC 238 au champ d'application biomasse-biocombustible-
bioénergieLes biocombustibles solides proviennent de différentes sources qui sont définies dans le cadre du
domaine d'application de l'ISO/TC 238 « Biocombustibles solides ». Les termes et les définitions sont
classés selon une structure logique basée sur le fait que les biocombustibles solides sont produits à
partir de différentes sources et qu'ils permettent de produire de la bioénergie :
— l'origine et la nature des biocombustibles solides dans la chaîne d'approvisionnement générale ;
— les différentes formes commercialisées et les différents types de biocombustibles issus du
processus de préparation ;— les propriétés les plus importantes des biocombustibles solides et les termes d'échantillonnage et
d'essai, ainsi que la classification et la spécification ;— la description des biocombustibles solides ainsi que leur manipulation et traitement, indiquée selon
la même structure que les sources de la biomasse ;— la bioénergie résultant de la conversion du biocombustible solide.
Les termes appropriés d'échantillonnage et d'essai ainsi que la classification et la spécification des
propriétés doivent être définis et décrits dans la catégorie nature/origine, type et propriétés des
biocombustibles solides. La nécessité des termes définis dans la présente Norme technique
internationale repose dans de nombreux cas sur le système de classification des biocombustibles
solides donné par l’ISO 17225-1, qui spécifie une classification plus détaillée des biocombustibles
solides.4 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s'appliquent.
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes :— ISO Online browsing platform : disponible à l’adresse http://www.iso.org/obp
— IEC Electropedia : disponible à l'adresse http://www.electropedia.org/
© ISO 2020 – Tous droits réservés
---------------------- Page: 7 ----------------------
ISO/DIS 16559:2020(F)
4.1
absorption
phénomène par lequel les atomes, ions ou molécules d'un gaz, liquide ou solide dissous pénètrent dans
un liquide ou un solide (l'absorbant) ou s’y dissolventNote 1 à l'article : Noter que l'adsorption est un processus de surface, alors que l'absorption met en jeu
l'intégralité du volume du matériau.[SOURCE : ISO 18757:2003, texte normatif résumé sous forme de termes et définitions]
4.2adsorption
phénomène par lequel les atomes, ions ou molécules d'un gaz, liquide ou solide dissous adhèrent à une
surface permettant au processus de générer un film d'adsorbat à la surface de l'adsorbant
[SOURCE : ISO 18757:2003, 3.1]4.3
additif
matériau qui a été introduit intentionnellement dans le produit de base du combustible afin d'améliorer
la qualité du combustible (par exemple les propriétés de combustion ou la durabilité), de réduire les
émissions ou de contribuer à la rentabilité de la productionNote 1 à l'article : Des traces, par exemple de graisse ou d’autres lubrifiants qui sont introduits pendant la
production du combustible dans le cadre d’opérations de broyage classique, ne sont pas considérées comme des
additifs.[SOURCE : ISO 17225-2:2014, 3.2]
4.4
agro-combustibles
biocombustibles obtenus à partir de cultures énergétiques et/ou de produits dérivés agricoles
(sous-produits agricoles)[SOURCE : FAO unified bioenergy terminology (UBET)]
4.5
séché à l'air
état dans lequel le biocombustible solide a été séché à l'air jusqu'à atteindre un état d'équilibre avec la
teneur en humidité[SOURCE : ISO 1213-2:1992 3.5, modifiée pour ce qui concerne les biocombustibles solides]
4.6angle de talus
angle critique de talus
angle de descente le plus raide d’un tas, mesuré en degrés, de la pente de matériau par rapport au plan
horizontal lorsqu'un matériau granulaire en face de pente est sur le point de glisser
Note 1 à l'article : L'angle de talus est normalement inférieur de quelques degrés à l'angle d’écoulement.
[SOURCE : ISO 4324:1977, 3]© ISO 2020 – Tous droits réservés
---------------------- Page: 8 ----------------------
ISO/DIS 16559:2020(F)
4.7
angle d'écoulement
angle de descente le plus raide dans un silo ou une trémie quand du matériau est retiré par le bas,
mesuré en degrés de la pente de matériau par rapport au plan horizontal, lorsqu'un matériau granulaire
en face de pente est sur le point de glisserNote 1 à l'article : L’angle d’écoulement est normalement supérieur de quelques degrés à l'angle de talus.
4.8biomasse animale
biomasse produite par les animaux d’élevage
4.9
produits dérivés de l'élevage
sous-produits de l'élevage
produits dérivés agricoles (ou sous-produits agricoles) provenant des animaux d’élevage
Note 1 à l'article : Ils comprennent notamment les excréments solides des animaux.
4.10biomasse aquatique
biomasse issue des plantes hydrophytiques ou hydrophytes, qui sont des plantes vivant dans ou sur des
environnements aquatiques[SOURCE : ISO 17225-1:2014, texte normatif résumé sous forme de termes et définitions]
4.11tel que déterminé
tel qu’analysé
teneur en humidité de référence du matériau lors de l'analyse/la détermination
Note 1 à l'article : L'abréviation de « tel que déterminé » est « ad ». Cette abréviation est utilisée comme indice
(par exemple : A est l’équivalent de teneur en cendre à la teneur en humidité lors de la détermination).
[SOURCE : ISO 1213-2:1992, texte résumé sous forme de termes et définitions pour ce qui concerne les
biocombustibles solides]4.12
à réception
lors de la livraison
base de calcul pour la matière lors de la livraison
Note 1 à l'article : L'abréviation de « à réception » est « ar ».
[SOURCE : ISO 15357:2011, 3.1, modifiée – « à la livraison » changé en « lors de la livraison »]
© ISO 2020 – Tous droits réservés---------------------- Page: 9 ----------------------
ISO/DIS 16559:2020(F)
4.13
cendre
teneur en cendre
total de cendres
masse de résidus inorganiques obtenue après combustion complète d'un combustible dans des
conditions spécifiées, généralement exprimée en pourcentage de la masse de matière sèche contenue
dans le combustibleNote 1 à l'article : Voir également fusibilité de cendre, cendre non exogène, teneur en cendre exogène.
Note 2 à l'article : Selon l’efficacité de la combustion, la cendre peut contenir des combustibles.
Note 3 à l'article : En cas de combustion complète, la cendre ne contient que des éléments inorganiques et non
combustibles.[SOURCE ISO 1213-2:1992, modifiée – texte résumé sous forme de termes et définitions pour ce qui
concerne les biocombustibles solides]4.14
température de déformation des cendres
température à laquelle apparaissent les premiers signes de courbure dus à la fusion sur les bords de
l'éprouvette de cendre4.15
température de fluidité des cendres
température à laquelle la cendre se répand sur la dalle de support en une couche dont la hauteur est
égale à la moitié de celle de l'éprouvette à la température hémisphérique de fusion des cendres
4.16fusibilité des cendres
comportement des cendres en fusion
état physique caractéristique de la cendre, obtenu par chauffage dans des conditions spécifiques
Note 1 à l'article : La fusibilité des cendres est déterminée dans des conditions d'oxydation ou de réduction.
Note 2 à l'article : Voir également température de déformation des cendres, température de fluidité des cendres,
température hémisphérique de fusion des cendres et température de contraction initiale des cendres.
4.17température hémisphérique de fusion des cendres
température à laquelle la hauteur d'une éprouvette préparée à partir de cendres suivant une procédure
particulière, est égale à la moitié de la largeur de la base, et prend pratiquement une forme
hémisphérique© ISO 2020 – Tous droits réservés
---------------------- Page: 10 ----------------------
ISO/DIS 16559:2020(F)
4.18
température de contraction initiale des cendres
SST
température à laquelle a lieu le retrait de l'éprouvette
Note 1 à l'article : Cette température est définie comme celle à laquelle la surface de l'éprouvette descend à moins
de 95 % de la surface originale de l'éprouvette à 550 °C.4.19
poids ensaché
poids du combustible, sac compris
4.20
biocombustible conditionné en balle
balle
biocombustible solide qui a été compressé puis lié afin de conserver sa forme et sa masse volumique
EXEMPLE Balles de paille, balles de culture herbacée à vocation énergétique, balles de rémanents forestiers.
4.21écorce
tissu cellulaire organique formé par des plantes de grande taille (arbres, buissons) à l’extérieur de la
zone de croissance (cambium) servant de protection du corps ligneux4.22
masse volumique basale
rapport de la masse en base anhydre au volume réel à l'état vert
4.23
biosourcé
issu de la biomasse
[SOURCE : EN 16575:2013, 2.1]
4.24
teneur biosourcée
fraction de combustible issue de la biomasse
Note 1 à l'article : Normalement exprimée en pourcentage de la masse totale du produit.
[SOURCE : EN 16575:2013, 2.4, modifiée – « produit » changé en « combustible »]4.25
produit biosourcé
produit industriel biosourcé
bioproduit
produit entièrement ou partiellement issu de la biomasse
Note 1 à l'article : Le produit biosourcé est normalement caractérisé par sa teneur en carbone biosourcé ou par sa
teneur biosourcée.[SOURCE : EN 16575:2013, 2.5]
© ISO 2020 – Tous droits réservés
---------------------- Page: 11 ----------------------
ISO/DIS 16559:2020(F)
4.26
bioénergie
énergie issue de la biomasse
4.27
biocombustible
combustible solide, liquide ou gazeux produit directement ou indirectement à partir de la biomasse
4.28assortiment biocombustible
biocombustible résultant du mélange intentionnel de différents biocombustibles
EXEMPLE Mélange de paille ou d'une culture herbacée à vocation énergétique avec du bois, de boue biologique
sèche avec de l'écorce.4.29
briquette biocombustible
biocombustible densifié réalisé avec ou sans additifs sous une forme géométrique prédéterminée avec au
moins deux diamètres de plus de 25 mm, par compression de la biomasse4.30
mélange biocombustible
biocombustible résultant du mélange naturel ou non intentionnel de différents biocombustibles et/ou de
différents types de biomasse4.31
granulé biocombustible
biocombustible densifié fabriqué avec ou sans additifs habituellement sous forme cylindrique, en général
d’une longueur comprise entre 5 mm et 40 mm et d’un diamètre allant jusqu’à 25 mm et avec des
extrémités non planes, produit par compression de la biomasseNote 1 à l'article : La biomasse a généralement été broyée avant densification.
Note 2 à l'article : Voir également granulé sans bois densifié, granulé de bois et granulé de biomasse traitée
thermiquement.4.32
biomasse
matériau d'origine biologique à l'exclusion des matériaux intégrés dans des formations géologiques
et/ou fossiliséesNote 1 à l'article : La biomasse est une matière organique d'origine végétale ou animale, comprenant sans
toutefois s’y limiter, les cultures énergétiques dédiées, cultures agricoles et arbres, les sous-produits de cultures
vivrières, fourragères et de plantes textiles, les sous-produits de plantes aquatiques, algues, sylviculture et bois,
les déchets agricoles, les produits dérivés de la transformation et autres matières organiques non fossilisées.
Note 2 à l'article : Voir également biomasse herbacée, biomasse fruitière et biomasse ligneuse.
4.33produit dérivé de la biomasse
produit connexe résultant involontairement de la fabrication d'un autre produit
EXEMPLE Sciure résultant du sciage de bois de construction.
© ISO 2020 – Tous droits réservés
---------------------- Page: 12 ----------------------
ISO/DIS 16559:2020(F)
4.34
sous-produits de transformation de la biomasse
biomasse récupérée lors de la récolte ou de la transformation de produits forestiers, agricoles,
aquacoles, en même temps que le produit principal exploité ou fabriquéEXEMPLE Grignon d'olives après pressage de l'huile, rémanents forestiers.
4.35
propriétaire de ressources en biomasse
personne physique ou entreprise disposant du droit d'exploiter les ressources en biomasse
Note 1 à l'article : Le propriétaire de ressources en biomasse peut être un propriétaire foncier ou sylvicole, une
société, etc.4.36
biométhane
méthane produit à partir de la biomasse (par exemple biocombustibles solides)
Note 1 à l'article : Le biométhane n'est pas un biocombustible solide. Ce terme est inclus uniquement à titre
d'information.4.37
boue biologique
boue formée dans le bassin d’aération au cours du traitement biologique des eaux résiduaires ou du
processus de transformation biologique et séparée par décantation ou flottationNote 1 à l'article : La boue biologique doit être traitée pour être transformée en biomasse solide.
4.38liqueur noire
fluide contenant de la lignine extraite du bois lors du processus de mise en pâte
Note 1 à l'article : La liqueur noire contient également des produits chimiques de mise en pâte.
Note 2 à l'article : La liqueur noire n'est pas un biocombustible solide. Ce terme est inclus uniquement à titre
d'information.4.39
pontage
voûtage
tendance des particules à former un arc stable au travers d’une ouverture, faisant obstacle au
déplacement[SOURCE : ISO/DIS 21637:2019, 3.8]
4.40
briquette de biomasse traitée thermiquement
briquette de biocombustible fabriquée à partir de biomasse traitée thermiquement
© ISO 2020 – Tous droits réservés
---------------------- Page: 13 ----------------------
ISO/DIS 16559:2020(F)
4.41
masse volumique apparente
masse d'une portion de matière particulaire divisée par le volume du contenant occupé par cette
portion dans des conditions spécifiques[SOURCE : ISO 1213-2:1992 3.21, modifiée pour ce qui concerne les biocombustibles solides]
4.42volume apparent
volume d'un matériau, y compris l'espace entre les particules
4.43
fagot biocombustible
fagot
ensemble de biocombustibles solides qui ont été liés ensemble dans le sens de la longueur
EXEMPLE Fagots de taillis à courte rotation, rémanents forestiers ou de petits arbres.
4.44pouvoir calorifique
valeur calorifique
quantité d’énergie par unité de masse libérée lors d'une combustion complète
Note 1 à l'article : Voir également pouvoir calorifique supérieur, densité d'énergie, pouvoir calorifique inférieur.
4.45cultures céréalières
cultures annuelles dont le principal objectif consiste à utiliser la semence pour la production
alimentaireNote 1 à l'article : Certaines cultures céréalières peuvent être utilisées comme biocombustible solide.
EXEMPLE Orge, blé, seigle, avoine.4.46
matériau de référence certifié
CRM
matériau de référence dont une ou plusieurs valeurs des propriétés sont certifiées par une procédure
techniquement valide accompagnée soit d’un certificat de traçabilité soit de tout autre document émis
par un organisme de certification[SOURCE : ISO 16967, 3.2, modifiée – définition mise à jour]
© ISO 2020 – Tous droits réservés
---------------------- Page: 14 ----------------------
ISO/DIS 16559:2020(F)
4.47
charbon de bois
biocharbon
biocarbone
biocoke
charbon vert
biocombustible solide obtenu par carbonisation, distillation ou pyrolyse de la biomasse
[SOURCE : ANSI/ASABE S593]4.48
traitement chimique
tout traitement impliquant des produits chimiques autres que l'air, l'eau ou la chaleur
[SOURCE : ISO 17225-7:2014, 3.3]4.49
paille hachée
paille coupée en petits morceaux
4.50
broyat
bois découpé avec des outils très tranchants et dans lequel la majeure partie du matériau présente des
longueurs de particule entre 50 et 150 mmNote 1 à l'article : Le broyat est de longueur sensiblement supérieure aux plaquettes de bois et d'aspect plus
grossier.4.51
coke
sous-produit solide de carbone impur obtenu à partir d'une matière première riche en carbone après
élimination des matières volatiles par distillation destructive[SOURCE : ANSI/ASABE S593-2006]
4.52
échantillon composite
échantillon constitué de tous les prélèvements élémentaires issus d'un lot ou d'un sous-lot
Note 1 à l'article : Les prélèvements élémentaires peuvent être réduits par division avant d'être ajoutés à
l'échantillon composite.Note 2 à l'article : Voir également l'Annexe A.
[SOURCE : EN 14780:2011, 3.1, modifiée – Ajout de la note 2]
4.53
arbre exploité à la culée noire
arbre, y compris les branches et les racines
Note 1 à l'article : Voir également arbre entier.
© ISO 2020 – Tous droits réservés
---------------------- Page: 15 ----------------------
ISO/DIS 16559:2020(F)
4.54
contamination
présence d'éléments indésirables tels que des éléments chimiques, physiques et/ou microbiologiques
dans le produit[SOURCE : ISO 22716:2007, 2.10]
4.55
coproduit
l'un quelconque de deux produits ou plus issus du même processus élémentaire ou système de produits
[SOURCE : ISO 14040:2006, 3.10]4.56
point critique de contrôle
point de contrôle qualité
CCP
point d'un processus ou entre plusieurs processus auquel les propriétés étudiées peuvent être évaluées
le plus aisément ; les points de contrôle qualité offrent également un potentiel des plus importants en
termes d'amélioration de la qualité4.57
culées et chutes de tronçonnage
petits morceaux de biomasse ligneuse produits lorsque l’extrémité des grumes ou des plots est
tronçonnée, avec ou sans écorce4.58
client
organisme ou personne qui reçoit un produit
[SOURCE : ISO 9000:2005, 3.3.5]
4.59
plaquettes
plaquettes de bois obtenues comme produit dérivé de l'industrie de transformation du bois, avec ou sans
écorce4.60
déflagration
événement violent consistant en une combustion subsonique qui se propage au moyen de matériau
chaud et en train de brûler (généralement de la poussière), qui chauffe la couche suivante de matériau
froid et l'enflamme suivant un enchaînement consécutifNote 1 à l'article : Ce processus peut être caractérisé comme un incendie explosif, durant lequel une partie du
matériau brûlant se dépose sur les surfaces se trouvant sur sa trajectoire, entraînant des blessures et dégâts
importants.[SOURCE : EN 13857-1:2003 2.13, modifiée pour ce qui concerne les biocombustibles solides]
© ISO 2020 – Tous droits réservés---------------------- Page: 16 ----------------------
ISO/DIS 16559:2020(F)
4.61
indice de déflagration
mesure en bar mètre par seconde et produit du taux de pression et propagation d'une explosion comme
établi par des normes d'essai4.62
contrat de livraison
contrat régissant le commerce de combustible, spécifiant par exemple l'origine et la source, la qualité et
la quantité de combustible, ainsi que les conditions de livraison4.63
lot livré
lot de biocombustible solide concentrant les exigences qualité essentielles pour un biocombustible solide
Note 1 à l'article : Le lot pour livraison peut être individu...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.