ISO 3547-3:2017
(Main)Plain bearings — Wrapped bushes — Part 3: Lubrication holes, grooves and indentations
Plain bearings — Wrapped bushes — Part 3: Lubrication holes, grooves and indentations
ISO 3547-3:2017 specifies dimensions of lubrication holes, grooves and bore indentations on wrapped bushes made of mono and multi-layer bearing material for plain bearing applications. NOTE Wrapped bushes with lubrication holes, grooves or bore indentations in accordance with this document can be ordered with dimensions in accordance with ISO 3547‑1 and made from materials in accordance with ISO 3547‑4.
Paliers lisses — Bagues roulées — Partie 3: Trous de graissage, rainures de graissage et creux de graissage
Drsni ležaji - Zvite puše - 3. del: Mazalne luknje, utori in žepki
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 3547-3:2020
01-oktober-2020
Drsni ležaji - Zvite puše - 3. del: Mazalne luknje, utori in žepki
Plain bearings - Wrapped bushes - Part 3: Lubrication holes, grooves and indentations
Paliers lisses - Bagues roulées
Ta slovenski standard je istoveten z: ISO 3547-3:2017
ICS:
21.100.10 Drsni ležaji Plain bearings
21.260 Mazalni sistemi Lubrication systems
SIST ISO 3547-3:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 3547-3:2020
---------------------- Page: 2 ----------------------
SIST ISO 3547-3:2020
INTERNATIONAL ISO
STANDARD 3547-3
Third edition
2017-02
Plain bearings — Wrapped bushes —
Part 3:
Lubrication holes, grooves and
indentations
Paliers lisses — Bagues roulées —
Partie 3: Trous de graissage, rainures de graissage et creux de
graissage
Reference number
ISO 3547-3:2017(E)
©
ISO 2017
---------------------- Page: 3 ----------------------
SIST ISO 3547-3:2020
ISO 3547-3:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 3547-3:2020
ISO 3547-3:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 1
5 General . 2
6 Lubrication holes . 2
7 Lubrication grooves . 3
7.1 General . 3
7.2 Type M1 . 3
7.2.1 General. 3
7.2.2 Type M1A . 4
7.2.3 Type M1B . 4
7.3 Type M2 . 5
7.3.1 General. 5
7.3.2 Type M2A . 6
7.3.3 Type M2B . 6
8 Lubrication indentations . 6
8.1 General . 6
8.2 Types N1 . 6
8.3 Type N2 . 7
8.4 Type N3 . 8
9 Designation . 9
Bibliography .10
© ISO 2017 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 3547-3:2020
ISO 3547-3:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This third edition cancels and replaces the second edition (ISO 3547-3:2006), which has been technically
revised.
A list of all the parts in the ISO 3547 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 3547-3:2020
INTERNATIONAL STANDARD ISO 3547-3:2017(E)
Plain bearings — Wrapped bushes —
Part 3:
Lubrication holes, grooves and indentations
1 Scope
This document specifies dimensions of lubrication holes, grooves and bore indentations on wrapped
bushes made of mono and multi-layer bearing material for plain bearing
...
INTERNATIONAL ISO
STANDARD 3547-3
Third edition
2017-02
Plain bearings — Wrapped bushes —
Part 3:
Lubrication holes, grooves and
indentations
Paliers lisses — Bagues roulées —
Partie 3: Trous de graissage, rainures de graissage et creux de
graissage
Reference number
ISO 3547-3:2017(E)
©
ISO 2017
---------------------- Page: 1 ----------------------
ISO 3547-3:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3547-3:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 1
5 General . 2
6 Lubrication holes . 2
7 Lubrication grooves . 3
7.1 General . 3
7.2 Type M1 . 3
7.2.1 General. 3
7.2.2 Type M1A . 4
7.2.3 Type M1B . 4
7.3 Type M2 . 5
7.3.1 General. 5
7.3.2 Type M2A . 6
7.3.3 Type M2B . 6
8 Lubrication indentations . 6
8.1 General . 6
8.2 Types N1 . 6
8.3 Type N2 . 7
8.4 Type N3 . 8
9 Designation . 9
Bibliography .10
© ISO 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 3547-3:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This third edition cancels and replaces the second edition (ISO 3547-3:2006), which has been technically
revised.
A list of all the parts in the ISO 3547 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 3547-3:2017(E)
Plain bearings — Wrapped bushes —
Part 3:
Lubrication holes, grooves and indentations
1 Scope
This document specifies dimensions of lubrication holes, grooves and bore indentations on wrapped
bushes made of mono and multi-layer bearing material for plain bearing applications.
NOTE Wrapped bushes with lubrication holes, grooves or bore indentations in accordance with this
document can be ordered with dimensions in accordance with ISO 3547-1 and made from materials in accordance
with ISO 3547-4.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.